Skip to the content
4 layers76 × 54 mmPixelblaze battery backpack, the printed circuit board in 3D

Small, Custom Tools for Electronics

Size
76 × 54 mm
Copper layers
4
Thickness
1.6 mm
Parts
112
Nets
134
Pads
485
Tracks, vias
953, 163
Pours
10
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
10 Aug 2023
Updated
18 Oct 2026

Overview

Pixelblaze battery backpack is an open-source printed circuit board by SK-Electronics-Consulting, from the SK-Electronics-Consulting/electronics-widgets repository on GitHub. It is a 4-layer board of 76 × 54 mm with 112 parts on 134 nets, routed with 953 tracks and 163 vias.

It is built around the RP2354A, HUSB238_002DD and TPS54560BDDAR, with the AP2112K-3.3TRG1, BQ25798RQMR and LIS3DH among its other parts. Its parts include 37 capacitors, 23 resistors, 20 diodes, 16 connectors and 6 ICs. It belongs with the power boards and the RP2350 boards of this library.

Main components

12

README

mm8130_rf_cal_kit/README.md

MM8130 RF Calibration Kit

A 1‑ and 2‑port VNA calibration kit presented at the Murata MM8130‑2600RA2 SWF‑type microwave coaxial switch‑connector interface (DC–6 GHz). Use it to calibrate a cable + Murata probe assembly (or a fixture that uses the SWF/MM8130 probe interface) to the probe tip, so the reference plane lands at the connector's center contact.

Status: V1, 2‑layer, ready for OSH Park. Design‑rule clean (0 DRC, 0 ERC, 0 schematic‑parity).

⚠️ AI‑generated design. This schematic and PCB layout were produced with AI assistance. Review every connection, value, footprint, and dimension against the datasheets before ordering or trusting it. The schematic and the board silkscreen carry the same warning.

Top render

Standards included (SOLT)

All standards sit on one non‑separable board. Each is an MM8130 receptacle with the standard element placed right at the RF contact. The Murata probe, when inserted, opens the connector's internal switch and contacts pin 1 (IN) — so every standard is defined between IN and GND.

RefStandardImplementation
J1OpenIN left unterminated (open); defined by the connector's fringing C.
J2ShortIN tied to the connector's own shell‑ground pads with short, wide copper + a ground via.
J3+R1Load50.0 Ω precision thin‑film RF resistor (Stackpole RNCQ 0603, HF) from IN to GND, placed at the contact.
J4↔J5Thru~50 Ω coplanar‑waveguide line, 5.18 mm IN‑to‑IN, between two MM8130s.

The switched OUT pin (pin 2) of every connector is intentionally left unconnected — the internal switch isolates it from IN while a probe is inserted, so loading it would only add a stub.

The connector (MM8130‑2600RA2)

  • Murata SWF‑type microwave coaxial connector with switch, 50 Ω, DC–6 GHz, 2.5 × 2.5 × 1.4 mm.
  • Normally the internal mechanical switch connects IN→OUT (signal passes through). Inserting a Murata probe breaks that path and connects the probe to IN. That is why all standards are referenced to IN.
  • Pinout: 1 = IN (center RF contact, probe‑contacted), 2 = OUT (switched), 3 = GND (shell, 4 lands).
  • LCSC C167503, DigiKey 490‑4981‑1‑ND, Mouser 81‑MM8130‑2600RA2.

Footprint

Custom footprint MM8130:MM8130-2600RA2 (in the project's MM8130.pretty), built from Murata catalog O30E ("Standard Pattern Dimension") and cross‑checked pad‑for‑pad against the vendor land pattern (LCSC C167503). Copper lands: two 0.50 × 0.58 mm signal pads (IN/OUT) on the center axis at ±1.16 mm, and four 0.75 × 0.80 mm ground lands at (±1.025, ±0.95) mm — reproducing the catalog's 2.80 mm ground span / 1.30 mm signal gap / 2.90 mm signal span.

Board / fabrication — OSH Park 2‑layer

  • Board size ≈ 46.5 × 15.0 mm, rounded rectangle with 3 mm corner fillets. Connector pitch is ~8 mm; the Thru pair is ~7.5 mm apart. Standards are probed one at a time during a cal, so the tighter spacing is fine — just confirm your specific Murata probe body clears a neighbour when inserted.
  • 2 × M3 mounting holes (3.2 mm, non‑plated) at the lower‑left and lower‑right corners (H1, H2), centred in the corner fillets, in a clear band below the connectors so screw heads/standoffs stay out of the probe area.

Using the kit (SOLT)

  1. Terminate your VNA cable with the mating Murata SWF probe (Murata O30E p.23 lists the probes).
  2. In the VNA's cal‑kit definition, enter the standard models:
    • Open: characterize the open capacitance (C0…C3) — the MM8130 open is not an ideal open.
    • Short: offset‑short with the small residual inductance of the via/copper.
    • Load: 50 Ω; the Stackpole RNCQ 0603 HF resistor is good but not a perfect broadband load — characterize if you need <‑30 dB return loss near 6 GHz.
    • Thru: one‑way delay ≈ 30 ps for the 5.18 mm CPW line (plus the two connector transitions). Measure it for the exact electrical length/loss.
  3. PCB standards are secondary standards — for best accuracy, characterize each one against a known‑good reference and store the measured models.

Next‑version ideas / caveats

  • The load uses an 0603 (chosen for easy hand‑soldering). It has more parasitic reactance than an 0402/0201, so characterize the load if you need high accuracy near 6 GHz; drop to 0402/0201 and shorten the stub for a better HF load.
  • If you want tight Thru impedance, a 4‑layer controlled‑impedance build (thin top dielectric) is the better route; on 2‑layer, keep the Thru as a characterized reference rather than a precise standard.
  • Characterize and label each standard with its measured model.

Sources

Parts

112
QtyValueFootprintReferences
140.1Capacitor_SMD:C_0402_1005MetricC1, C6, C8, C15, C22, C23, C24, C25, C26, C27, C28, C29, C30, C31
81kResistor_SMD:R_0402_1005MetricR1, R2, R9, R14, R19, R20, R22, R23
8Xinglight_XL-4020RGBC-2812BLED_SMD:LED_Xinglight_XL-4020RGBC-2812B_4x2mm_P0.85mmD4, D10, D11, D12, D13, D14, D15, D16
610Capacitor_SMD:C_0603_1608MetricC2, C3, C7, C9, C11, C12
64.7Capacitor_SMD:C_0402_1005MetricC16, C17, C19, C34, C35, C36
6WS2812B-2020LED_SMD:LED_WS2812B-2020_PLCC4_2.0x2.0mmD3, D5, D6, D7, D8, D9
5Conn_01x04Connector_Molex:Molex_Micro-Fit_3.0_43650-0415_1x04_P3.00mm_VerticalJ9, J10, J11, J14, J15
422uCapacitor_SMD:C_0805_2012MetricC10, C13, C14, C18
4Conn_01x01Battery:BatteryClip_Keystone_54_D16-19mmJ1, J2, J3, J4
327Resistor_SMD:R_0402_1005MetricR15, R16, R18
3LED_SmallLED_SMD:LED_0603_1608MetricD1, D17, D20
210kResistor_SMD:R_0402_1005MetricR12, R17
215pFCapacitor_SMD:C_0402_1005MetricC32, C33
247nCapacitor_SMD:C_0402_1005MetricC4, C5
2Conn_01x04Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ7, J13
2Jumper_2_Small_BridgedJumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mmJP1, JP2
2R_SmallResistor_SMD:R_0402_1005MetricR3, R4
2SK6812MINI-ELED_SMD:LED_SK6812MINI-E_3.2x2.8mm_P1.5mm_ReverseMountD18, D19
2SW_PushButton_Switch_SMD:SW_SPST_TS-1088-xR020SW2, SW3
11.0uInductor_SMD:L_Changjiang_FXL0630L1
1100Resistor_SMD:R_0402_1005MetricR8
110kResistor_SMD:R_0603_1608MetricTH1
112MHzCrystal:Crystal_SMD_3225-4Pin_3.2x2.5mmY1
116.9kResistor_SMD:R_0402_1005MetricR10
11nCapacitor_SMD:C_0402_1005MetricC37
1243kResistor_SMD:R_0402_1005MetricR13
13.3uInductor_SMD:L_0806_2016MetricL3
130.31kResistor_SMD:R_0402_1005MetricR6
133uHInductor_SMD:L_Changjiang_FXL1040L2
14700pCapacitor_SMD:C_0402_1005MetricC21
147pCapacitor_SMD:C_0402_1005MetricC20
15.23kResistor_SMD:R_0402_1005MetricR5
152.3kResistor_SMD:R_0402_1005MetricR11
16.04kResistor_SMD:R_0402_1005MetricR7
1AP2112K-3.3Package_TO_SOT_SMD:SOT-23-5U6
1BQ25798Package_DFN_QFN:Texas_RQM0029A_VQFN-29_4x4mm_P0.4mmU3
1Conn_01x08Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_VerticalJ12
1Conn_ARM_SWD_TagConnect_TC2030Connector:Tag-Connect_TC2030-IDC-FP_2x03_P1.27mm_VerticalJ6
1Conn_QWIIC_HorizontalConnector_JST:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_HorizontalJ8
1HUSB238Package_DFN_QFN:WDFN-10-1EP_3x3mm_P0.5mm_EP1.8x2.5mmU1
1LIS3DHPackage_LGA:LGA-16_3x3mm_P0.5mm_LayoutBorder3x5yU4
1RP2354APackage_DFN_QFN:QFN-60-1EP_7x7mm_P0.4mm_EP3.4x3.4mmU7
1RX_TX_Swap_SMDSKEC_Footprints:RX_TX_SWAP_0402R21
1SK86CDiode_SMD:D_SMCD2
1SM03B-SRSS-TBConnector_JST:JST_SH_SM03B-SRSS-TB_1x03-1MP_P1.00mm_HorizontalJ16
1SW_SPDTButton_Switch_SMD:SW_SPDT_Shouhan_MSK12C02SW1
1TPS54560BDDAPackage_SO:Texas_R-PDSO-G8_EP2.95x4.9mm_Mask2.4x3.1mm_ThermalViasU5
1USB_C_Receptacle_USB2.0_16PConnector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12J5

More from SK-Electronics-Consulting/electronics-widgets

12
  • 4 layers82 × 40 mmGridfinity USB hub, the printed circuit board in 3D

    Gridfinity USB hub

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    124 parts1
  • 4 layers70 × 70 mmHUSB238A Dev Board, the printed circuit board in 3D

    HUSB238A Dev Board

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    44 parts1
  • 4 layers11.1 × 40.5 mmSAO tree ornament, the printed circuit board in 3D

    SAO tree ornament

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    23 parts1
  • 4 layers25 × 25.5 mmQwiic CAN Saleae Adapter, the printed circuit board in 3D

    Qwiic CAN Saleae Adapter

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    15 parts1
  • 4 layers25.5 × 27 mmJlink adapter, the printed circuit board in 3D

    Jlink adapter

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    13 parts1
  • 2 layers46.5 × 15 mmMm8130 rf cal kit, the printed circuit board in 3D

    Mm8130 rf cal kit

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    9 parts1
  • 2 layers28.5 × 17 mmCR2032 battery load tester, the printed circuit board in 3D

    CR2032 battery load tester

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    5 parts1
  • 2 layers7.5 × 10 mmREF33xx Breadboard Adapter, the printed circuit board in 3D

    REF33xx Breadboard Adapter

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    4 parts1
  • 2 layers9.3 × 13.3 mmRasPi Power Adapter, the printed circuit board in 3D

    RasPi Power Adapter

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    3 parts1

Similar boards

  • 4 layers100 × 100 mmLabathome pcb, the printed circuit board in 3D

    Labathome pcb

    klaus-liebler/labathome

    Der kleine Bruder von lab@home. Ermöglicht das Experimentieren mit PT1...PTn-Gliedern, die intern als RC-Kombination (entkoppelt über Operationsverstärker) ausgeführt sind.

    292 parts5MIT
  • 4 layers110 × 80 mmSpin rig controller, the printed circuit board in 3D

    Spin rig controller

    Tinkerbug-Robotics/TinkerRocket

    Model rocket flight computer, ground station, iOS app, and simulation

    170 parts1GPL-3.0
  • 4 layers260 × 110 mmPandore, the printed circuit board in 3D

    Pandore

    filliformes/pandore

    pandore is an open-source digital audio instrument protyping platform based on the LattePanda Mu.

    804 parts2
  • 4 layers173.2 × 52.5 mmCanSat, the printed circuit board in 3D

    CanSat

    budabalint/T.E.E.M.O

    442 parts
  • 6 layers90 × 124.1 mmTome nano 100, the printed circuit board in 3D

    Tome nano 100

    i2cjak/Chudx_Nano_100

    a really cool macropad that's opensource btw

    108 partsCERN-OHL-P-2.0
  • 2 layers72 × 133 mmLoFence, the printed circuit board in 3D

    LoFence

    Alex9779/LoFence_Hardware

    The LoFence V2 PCB is designed with KiCad.

    73 parts1
  • 2 layers88 × 115 mmBadge, the printed circuit board in 3D

    Badge

    endsummercamp/badge

    Per l'anno 2024 anche l'End Summer Camp si vuole dotare di un badge interattivo e programmabile, in linea con gli eventi simili internazionali.

    131 parts1CERN-OHL-P-2.0
  • 4 layers85.1 × 87.7 mmArt big paw, the printed circuit board in 3D

    Art big paw

    HeyPCB/led-art

    Shaped LED boards inspired by films, each in its own colour: KiCad 10, JLCPCB-ready, CERN-OHL-S-2.0

    48 partsCERN-OHL-S-2.0

Questions

How big is the Pixelblaze battery backpack PCB?

It measures 76 × 54 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Pixelblaze battery backpack use?

112 parts, built around the RP2354A, HUSB238_002DD, TPS54560BDDAR and AP2112K-3.3TRG1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Pixelblaze battery backpack KiCad files?

From the SK-Electronics-Consulting/electronics-widgets repository on GitHub, at the commit this page was made from: the board is pixelblaze_battery_backpack/pixelblaze_battery_backpack.kicad_pcb and its schematic Breadboard Power Supply Adapter/Breadboard Power Supply Adapter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Pixelblaze battery backpack design in my own project?

Its repository states no licence, so its author keeps all rights: ask SK-Electronics-Consulting before reusing the design.