2 layers88.9 × 88.4 mm
2 layers123.8 × 73.5 mm
Minimalist flight-control toolkit for makers
- Size
- 123.8 × 73.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 40
- Nets
- 24
- Pads
- 64
- Tracks, vias
- 157, 10
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 31 Dec 2015
- Updated
- 7 Nov 2026
Overview
Attic is an open-source printed circuit board by simondlevy, from the simondlevy/Hackflight repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 123.8 × 73.5 mm with 40 parts on 24 nets, routed with 157 tracks and 10 vias.
Its parts include 27 connectors, 4 diodes and 3 resistors.
README
attic/kicad/main/README.md
Secure M2 nylon machine screws
Before soldering on any of the components, you'll need to decide how you're going to mount the PCB to your airframe. I've also used VHB tape, which doesn't require screws, but for a cleaner build the PCB provides four mounting holes in the popular 26x26mm diamond configuration, for use with M2 nylon machine screws. You secure these screws temporarily with nuts before using a rubber grommit for vibration dampening.
BOM, in order of soldering
Note: I recommend using Scotch tape to mask the pins you're not currently soldering, and doing a continuity check for bridges/shorts after each step:
-
Pololu 5V Step-Up/Step-Down Voltage Regulator S7V7F5, on bottom, using 1-2mm chisel/bevel tip.
-
28AWG silicone-insulated wire for hover-deck, protruding from bottom, using 0.2-0.8mm fine/conical tip.
-
SHUTTLE BOARD 3.0 BMI088, on top, using 0.2-0.8mm fine/conical tip. To avoid soldering a bridge (short circuit), you should solder only the six indicated pins (3V3, GND, SCL0, GD, SDA0, 3V3).
-
28AWG silicone-insulated wires to 4-in-1 ESC, protruding from bottom, using 0.2-0.8mm fine/conical tip. Most 4-in-1 ESCs come with this connector, or you can build one yourself using a kit like this.
-
220Ω resistor, on bottom, using 1-2mm chisel/bevel tip.
-
LED, on top, using 1-2mm chisel/bevel tip.
Teensy / ESP32 Xiao C6
https://www.amazon.com/Breakaway-Headers-Connector-Breadboard-Electronic/dp/B0FLJVHSRN/
Parts
40| Qty | Value | Footprint | References |
|---|---|---|---|
| 17 | Conn_01x01_Pin | Connector_Wire:SolderWirePad_1x01_SMD_2x4mm | J5, J6, J7, J8, J10, J11, J12, J13, J14, J15, J16, J17, J18, J20, J21, J22 +1 |
| 8 | Conn_01x01_Pin | Connector_PinSocket_2.54mm:PinSocket_1x01_P2.54mm_Vertical | J24, J25, J26, J27, J28, J29, J30, J31 |
| 4 | LED | LED_THT:LED_D3.0mm_FlatTop | D1, D2, D3, D4 |
| 3 | , , | ||
| 2 | Conn_01x10 | Connector_PinSocket_2.54mm:PinSocket_1x10_P2.54mm_Vertical | J1, J2 |
| 2 | MountingHole | MountingHole:MountingHole_4mm | H1, H1 |
| 1 | LOGO | LOGO | G*** |
| 1 | R1 | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R2 |
| 1 | R2 | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R3 |
| 1 | R_LED | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1 |
Questions
How big is the Attic PCB?
It measures 123.8 × 73.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Attic use?
40 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Attic KiCad files?
From the simondlevy/Hackflight repository on GitHub, at the commit this page was made from: the board is attic/kicad/tx/tx.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Attic design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
More from simondlevy/Hackflight
12- 2 layers120.5 × 73.5 mm
- 2 layers39.8 × 55.1 mm
- 2 layers41 × 41.5 mm
- 2 layers39.8 × 73.9 mm
- 2 layers
- 2 layers41 × 55.5 mm
- 2 layers41 × 48 mm
- 2 layers47.6 × 51 mm
- 2 layers52 × 24.8 mm
- 2 layers47 × 46.3 mm
- 2 layers41 × 44.5 mm
Similar boards
- 2 layers139.7 × 73.7 mm
- 2 layers149.4 × 177.4 mm
Lightsculpture
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
40 parts915 - 2 layers150 × 50 mm
EleLab v2 Bus150
Chrismettal/EleLab_v2
Cheap DIY lab system for hobbyists and the tinkering folk
40 parts531GPL-3.0 - 2 layers66.4 × 48.1 mm
Raspberry
Chrismettal/flipper-zero-backpacks
Backpack-style addon boards for the Flipper Zero!
40 parts456 - 2 layers44 × 44 mm
- 2 layers90.8 × 53.3 mm
- 2 layers59.6 × 109.5 mm
Drop
ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust
40 parts410 - 2 layers80.9 × 56.2 mm
Adapter
kervinck/gigatron-rom
System, apps and tooling for the Gigatron TTL microcomputer
40 parts292BSD-2-Clause