2 layers88.9 × 88.4 mm
2 layers
Bottom
simondlevy/Hackflight334Minimalist flight-control toolkit for makers
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 18
- Nets
- 41
- Pads
- 68
- Tracks, vias
- 11, 0
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 31 Dec 2015
- Updated
- 7 Nov 2026
Overview
Bottom is an open-source printed circuit board by simondlevy, from the simondlevy/Hackflight repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board with 18 parts on 41 nets, routed with 11 tracks and 0 vias.
README
attic/kicad/main/README.md
Secure M2 nylon machine screws
Before soldering on any of the components, you'll need to decide how you're going to mount the PCB to your airframe. I've also used VHB tape, which doesn't require screws, but for a cleaner build the PCB provides four mounting holes in the popular 26x26mm diamond configuration, for use with M2 nylon machine screws. You secure these screws temporarily with nuts before using a rubber grommit for vibration dampening.
BOM, in order of soldering
Note: I recommend using Scotch tape to mask the pins you're not currently soldering, and doing a continuity check for bridges/shorts after each step:
-
Pololu 5V Step-Up/Step-Down Voltage Regulator S7V7F5, on bottom, using 1-2mm chisel/bevel tip.
-
28AWG silicone-insulated wire for hover-deck, protruding from bottom, using 0.2-0.8mm fine/conical tip.
-
SHUTTLE BOARD 3.0 BMI088, on top, using 0.2-0.8mm fine/conical tip. To avoid soldering a bridge (short circuit), you should solder only the six indicated pins (3V3, GND, SCL0, GD, SDA0, 3V3).
-
28AWG silicone-insulated wires to 4-in-1 ESC, protruding from bottom, using 0.2-0.8mm fine/conical tip. Most 4-in-1 ESCs come with this connector, or you can build one yourself using a kit like this.
-
220Ω resistor, on bottom, using 1-2mm chisel/bevel tip.
-
LED, on top, using 1-2mm chisel/bevel tip.
Teensy / ESP32 Xiao C6
https://www.amazon.com/Breakaway-Headers-Connector-Breadboard-Electronic/dp/B0FLJVHSRN/
Parts
18| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | Conn_01x03_Female | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | M1_GND1, VL53L1_L3, VL53L1_L4, VL53L1_L5, VL53L1_R1, VL53L1_R2 |
| 4 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | POST_1, POST_2, POST_3, POST_4 |
| 3 | Conn_01x04_Female | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | PMW3901_L1, PMW3901_R1, REG1 |
| 2 | Conn_01x01 | Connector_Wire:SolderWirePad_1x01_SMD_5x10mm | GND_PAD1, VB_PAD1 |
| 1 | Conn_01x02_Female | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | PMW3901_PWR1 |
| 1 | Conn_01x12_Socket | Connector_PinSocket_2.54mm:PinSocket_1x14_P2.54mm_Vertical | J1 |
| 1 | Conn_01x16_Socket | Connector_PinSocket_2.54mm:PinSocket_1x16_P2.54mm_Vertical | J2 |
Questions
What parts does the Bottom use?
18 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Bottom KiCad files?
From the simondlevy/Hackflight repository on GitHub, at the commit this page was made from: the board is attic/kicad/feather/bottom/bottom.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Bottom design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
More from simondlevy/Hackflight
12- 2 layers123.8 × 73.5 mm
- 2 layers120.5 × 73.5 mm
- 2 layers39.8 × 55.1 mm
- 2 layers41 × 41.5 mm
- 2 layers39.8 × 73.9 mm
- 2 layers41 × 55.5 mm
- 2 layers41 × 48 mm
- 2 layers47.6 × 51 mm
- 2 layers52 × 24.8 mm
- 2 layers47 × 46.3 mm
- 2 layers41 × 44.5 mm
Similar boards
- 2 layers27.9 × 16.5 mm
- 2 layers42.7 × 13.7 mm
Stm32-mini12864
VoronDesign/Voron-Hardware
Cool Hardware designed by the Voron Design group
18 parts1.1kGPL-3.0 - 2 layers41.2 × 46.6 mm
- 2 layers44 × 51.3 mm
4272MAVcoder R4
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
18 parts915 - 2 layers28.3 × 14.3 mm
Tap Photosensor PCB
VoronDesign/Voron-Tap
Tap is a nozzle-based z-probe for the V2 and Trident printer designs. The entire toolhead moves to trigger an optical switch. Tap offers many advantages:
18 parts716GPL-3.0 - 2 layers20.3 × 15.2 mm
L0 stepper driver
Luos-io/luos_engine
Open-source and real-time orchestrator for cyber-physical-systems, to easily design, test and deploy embedded applications and digital twins.
18 parts546MIT - 2 layers
- 2 layers42.5 × 28.8 mm
C5VRX JACK DIY V2
Twotoz/C5VRX
Ultra-minimal, zero-CPU 5.8 GHz analog FPV video receiver using ESP32-C5 Wi-Fi 6 PHY MODEM_DIAG, BitScrambler WBFM demodulation & resistor DAC CVBS
18 parts515GPL-3.0