2 layers88.9 × 88.4 mm
2 layers40 × 34.2 mm
Minimalist flight-control toolkit for makers
- Size
- 40 × 34.2 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 12
- Nets
- 20
- Pads
- 77
- Tracks, vias
- 76, 3
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 31 Dec 2015
- Updated
- 7 Nov 2026
Overview
Top is an open-source printed circuit board by simondlevy, from the simondlevy/Hackflight repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 40 × 34.2 mm with 12 parts on 20 nets, routed with 76 tracks and 3 vias.
Its parts include 2 connectors and 1 diode.
README
attic/kicad/main/README.md
Secure M2 nylon machine screws
Before soldering on any of the components, you'll need to decide how you're going to mount the PCB to your airframe. I've also used VHB tape, which doesn't require screws, but for a cleaner build the PCB provides four mounting holes in the popular 26x26mm diamond configuration, for use with M2 nylon machine screws. You secure these screws temporarily with nuts before using a rubber grommit for vibration dampening.
BOM, in order of soldering
Note: I recommend using Scotch tape to mask the pins you're not currently soldering, and doing a continuity check for bridges/shorts after each step:
-
Pololu 5V Step-Up/Step-Down Voltage Regulator S7V7F5, on bottom, using 1-2mm chisel/bevel tip.
-
28AWG silicone-insulated wire for hover-deck, protruding from bottom, using 0.2-0.8mm fine/conical tip.
-
SHUTTLE BOARD 3.0 BMI088, on top, using 0.2-0.8mm fine/conical tip. To avoid soldering a bridge (short circuit), you should solder only the six indicated pins (3V3, GND, SCL0, GD, SDA0, 3V3).
-
28AWG silicone-insulated wires to 4-in-1 ESC, protruding from bottom, using 0.2-0.8mm fine/conical tip. Most 4-in-1 ESCs come with this connector, or you can build one yourself using a kit like this.
-
220Ω resistor, on bottom, using 1-2mm chisel/bevel tip.
-
LED, on top, using 1-2mm chisel/bevel tip.
Teensy / ESP32 Xiao C6
https://www.amazon.com/Breakaway-Headers-Connector-Breadboard-Electronic/dp/B0FLJVHSRN/
Parts
12| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | Conn_01x01 | Connector_Wire:SolderWirePad_1x01_SMD_5x10mm | GND_PAD18, GND_PAD19, GND_PAD20, GND_PAD21 |
| 2 | 2.2k Ohms | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | 2.2k, 2.2k |
| 2 | Conn_01x15_MountingPin | Connector_IDC:IDC-Header_2x15_P2.54mm_Vertical | J1, J1 |
| 1 | 47 Ohms | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | 47 |
| 1 | Conn_01x02_Female | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | PMW3901_PWR2 |
| 1 | Conn_01x03_Female | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | Motor5 |
| 1 | LED | LED_THT:LED_D3.0mm | D1 |
Questions
How big is the Top PCB?
It measures 40 × 34.2 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Top use?
12 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Top KiCad files?
From the simondlevy/Hackflight repository on GitHub, at the commit this page was made from: the board is attic/kicad/weact/top/top.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Top design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
More from simondlevy/Hackflight
12- 2 layers123.8 × 73.5 mm
- 2 layers120.5 × 73.5 mm
- 2 layers39.8 × 55.1 mm
- 2 layers41 × 41.5 mm
- 2 layers39.8 × 73.9 mm
- 2 layers
- 2 layers41 × 55.5 mm
- 2 layers41 × 48 mm
- 2 layers47.6 × 51 mm
- 2 layers52 × 24.8 mm
- 2 layers47 × 46.3 mm
Similar boards
- 2 layers
Nrf bga
github-linguist/linguist
Language Savant. If your repository's language is being reported incorrectly, send us a pull request!
12 parts14kMIT - 2 layers66.9 × 74.5 mm
- 2 layers40 × 15 mm
Sensors
google/mozc-devices
Circuit diagrams and firmware source code for Gboard DIY keyboards
12 parts3kApache-2.0 - 2 layers42.7 × 56.5 mm
- 2 layers26 × 16.9 mm
- 2 layers49 × 25 mm
5v boost regulator
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
12 parts915 - 2 layers28.3 × 10.3 mm
Tap Photosensor PCB
VoronDesign/Voron-Tap
Tap is a nozzle-based z-probe for the V2 and Trident printer designs. The entire toolhead moves to trigger an optical switch. Tap offers many advantages:
12 parts716GPL-3.0 - 2 layers25.4 × 70.4 mm
Tpmsniffer
stacksmashing/pico-tpmsniffer
A simple, very experimental TPM sniffer for LPC bus
12 parts696