
Power node
shonzinger-spec/ee-portfolio
Electrical engineering portfolio: simulated and verified EE projects (firmware, SPICE, KiCad, Wokwi) by Shon Zinger

Electrical engineering portfolio: simulated and verified EE projects (firmware, SPICE, KiCad, Wokwi) by Shon Zinger
Sync buck is an open-source printed circuit board by shonzinger-spec, from the shonzinger-spec/ee-portfolio repository on GitHub, published under the MIT licence. It is a 2-layer board of 54 × 40 mm with 37 parts on 20 nets, routed with 118 tracks and 113 vias.
It is built around the UCC27211D. Its parts include 13 resistors, 12 capacitors, 3 connectors, 2 ICs and 2 transistors. It belongs with the power boards and the ESP32 boards of this library.
Electrical engineering projects by Shon Zinger, a York University EE graduate. Each project is fully virtual and reproducible with free tools: a standalone Python model runs with numpy and matplotlib only, and the simulation, schematic and firmware checks are documented with real output pasted into the project README. No hardware was built.
| # | Project | What it shows | Verification |
|---|---|---|---|
| 01 | Smart power-monitoring IoT node | ESP32 + INA219 power monitor on a 5 V / 2 A rail with an SSD1306 display: 50 mOhm Kelvin shunt, register-level driver, two-task FreeRTOS firmware | main.py self-check, LTspice and ngspice 6/6, host test 33/33, KiCad ERC 0 errors, PCB DRC + schematic parity 0 violations (check_pcb.py 13/13), Wokwi live run |
| 02 | Digital synchronous buck converter | 12 V to 5 V / 3 A, 200 kHz synchronous buck with discrete FETs, RC snubber and a digital PI loop in C (input and reference feed-forward, DPWM hysteresis, anti-windup, over-current latch) | main.py 59/59, LTspice vs ngspice cross-check, host test 19/19 + negative gate 4/4, KiCad ERC 0 errors |
| 03 | Ladder-to-DXF schematic generator | NEMA/JIC motor-starter ladder drawn from a device list: automatic device tags, wire numbers and coil/contact cross-references, DXF for any CAD program, BOM and wire list in Excel | main.py self-check, pytest 22/22, ezdxf audit 0 errors |
| 04 | Smart BMS simulator | 4S Li-ion pack: equivalent-circuit and thermal-runaway cell model, BMS firmware in C with OV/UV/OCD/SCD/temperature protection, coulomb-counting SoC, passive balancing and a cell-level end of charge | main.py 30/30, host test 34/34 + negative gate 6/6, ngspice 128 corners, KiCad ERC 0 errors |
| 05 | BLDC motor controller, hardware-in-the-loop | 24 V BLDC with Hall 6-step commutation: timer-interrupt PWM in C with firmware dead-time insertion, cascaded speed/current PI on a sampled DC-link shunt, over-current/Hall/stall protection, run against a switch-level inverter and motor model | main.py 26/26, host test 33/33 + negative gate 7/7, ngspice dead-time sweep and full inverter (within 1.5 % of the plant), KiCad ERC 0 errors |
Highlights of project 01:
NN-name/).main.py) that runs without a complex install chain.Author: Shon Zinger
AI assistance: Claude (Anthropic) helped with parts of each project; the Credits section of each project README says which.
License: MIT, see LICENSE.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 10k | Resistor_SMD:R_0603_1608Metric | R3, R4, R7, R10, R11, R13 |
| 4 | MountingHole_3.2mm_M3 | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 3 | 1nF | Capacitor_SMD:C_0603_1608Metric | C10, C11, C12 |
| 2 | 10uF 25V X7R | Capacitor_SMD:C_1210_3225Metric | C1, C2 |
| 2 | 2.2R | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 2 | 30V 7mOhm NMOS (generic) | Package_TO_SOT_SMD:TO-252-3_TabPin2 | Q1, Q2 |
| 1 | 1.8R | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 100nF | Capacitor_SMD:C_0603_1608Metric | C9 |
| 1 | 100nF 50V | Capacitor_SMD:C_0603_1608Metric | C5 |
| 1 | 100uF 25V electrolytic | Capacitor_THT:CP_Radial_D8.0mm_P3.50mm | C3 |
| 1 | 10uF 10V X7R | Capacitor_SMD:C_0805_2012Metric | C8 |
| 1 | 15uH Isat>=6A DCR 20mOhm | Inductor_SMD:L_Bourns_SRP1245A | L1 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric | R9 |
| 1 | 1nF 50V C0G | Capacitor_SMD:C_0603_1608Metric | C6 |
| 1 | 1uF 25V | Capacitor_SMD:C_0603_1608Metric | C4 |
| 1 | 470uF 6.3V polymer | Capacitor_SMD:CP_Elec_6.3x7.7 | C7 |
| 1 | 47k | Resistor_SMD:R_0603_1608Metric | R12 |
| 1 | 5mOhm 1% | Resistor_SMD:R_Shunt_Vishay_WSK2512_6332Metric_T1.19mm | R6 |
| 1 | 6.8k | Resistor_SMD:R_0603_1608Metric | R8 |
| 1 | ESP32 DevKit | Connector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_Vertical | J3 |
| 1 | INA181A3 | Package_TO_SOT_SMD:SOT-23-6 | U2 |
| 1 | UCC27211 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | VIN 12V | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | VOUT 5V | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J2 |

shonzinger-spec/ee-portfolio
Electrical engineering portfolio: simulated and verified EE projects (firmware, SPICE, KiCad, Wokwi) by Shon Zinger


Deco025/resonare
Resonare: open-source 120 W LCC-S resonant wireless charger, transmitter and receiver boards (KiCad 10, 4-layer)

BenjaminMeyerEE/Digital-Synchronous-Buck-Converter
12 V to 6 V, 10 A synchronous buck converter with closed-loop digital control on an STM32G474RET6. Custom 4-layer board in KiCad.

Blaze-Pascal/EKA-PiF-MCU_PSU
2-phase synchronous digitally controlled buck converter (30V in, up to 10A out). Features a 4-layer custom KiCad PCB optimized for EMI.

IpinZhu/foc-esc
这是一个基于 STM32G473RC 的实验性三相 PMSM/BLDC 电机控制平台。仓库包含驱动板设计,以及使用 Rust 2024 + Embassy 实现的电流控制型磁场定向控制(FOC)固件。



chainstart/makerai-lab
MakerAI hardware-agent research, whitepaper, lab artifacts, and MVP pipeline
It measures 54 × 40 mm and has 2 copper layers, 1.6 mm thick.
37 parts, built around the UCC27211D. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the shonzinger-spec/ee-portfolio repository on GitHub, at the commit this page was made from: the board is 02-sync-buck/hw/kicad/sync_buck.kicad_pcb and its schematic 01-smart-power-node/hw/kicad/power_node.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).