Skip to the content
4 layers120.5 × 269.9 mmRabbit body, the printed circuit board in 3D

rabbit source code

Size
120.5 × 269.9 mm
Copper layers
4
Thickness
1.6 mm
Parts
346
Nets
226
Pads
1,182
Tracks, vias
3,179, 684
Pours
51
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
16 Jun 2025
Updated
19 Oct 2026

Overview

Rabbit body is an open-source printed circuit board by seralexeev, from the seralexeev/rabbit repository on GitHub. It is a 4-layer board of 120.5 × 269.9 mm with 346 parts on 226 nets, routed with 3,179 tracks and 684 vias.

It is built around the INA226AIDGSR, DRV8316CRRGFR and LM61495RPHR, with the AO3400A, SMBJ20A and BSC010N04LS among its other parts. Its parts include 136 resistors, 108 capacitors, 14 diodes, 10 connectors and 8 ICs.

Main components

12

README

pcb/rabbit-body-c/README.md

Body board rev C: netlist, placement, routing

Status 2026-10-11: netlist and two-sided placement done (floorplan of 2026-10-11 in gen/placement.json); routing on 8 layers in progress (autorouter plateau 27-29 unrouted connections, the rest is being finished by hand).

  • The approved spec is docs/reports/2026-10-10-body-pcb-rev-c.md (Russian). Its §11a decisions and the "10-11 October" section override older data.
  • The per-IC source tables are data/pcb-revc/ics/*.json (gitignored); reviews and the applied fixes are in data/pcb-revc/review/.
  • The generator gen/design.py is the single source of truth for parts, nets and default positions; gen/placement.json (263 overrides, applied at the end of design.py) moves parts to the 2026-10-11 floorplan.
  • History: docs/log/2026-10-10-body-pcb-rev-c.md.
text
python3 gen/footprints.py                       # custom footprints -> lib/rabbit_body.pretty
python3 gen/outline_revc.py                     # outline.json + the corner ToF poses in tof.json (from kit_outline.json)
PY=/Applications/KiCad/KiCad.app/Contents/Frameworks/Python.framework/Versions/3.9/bin/python3
$PY gen/build_board.py --no-route               # placement only (without --no-route: + planes and pours, gen/routing.py)
gen/make.sh                                     # full run: build, fill, fastroute/Freerouting, cleanup, DRC (SES=... reuses a route)
python3 gen/check_netlist.py [--board]          # netlist checks (--board needs $PY)
$PY gen/drc_summary.py                          # kicad-cli DRC -> fab/drc.json
$PY gen/power_check.py                          # copper width and vias of the high-current nets after routing
python3 gen/stock.py [boards]                   # JLC stock of every BOM line (default 2 boards) -> fab/stock.json + csv
PLOTPY=<python with matplotlib> gen/render.sh   # renders/top, bottom (seen from below), iso, *_labelled

Board

  • Outline (gen/outline_revc.py -> gen/outline.json): X -70..70, Y -158..156.2 (board frame: origin at the deck centre, +Y = robot front, top view). The kit plate grown on 2026-10-11 (owner): the tail goes to Y -158 and the board is ±70 wide from the tail to Y 30 (9.8 mm to the rear wheels' inner faces); the front keeps the kit's waist for the steering sweep; the nose goes to Y 156.2 so the ZED 2i (43.1 mm deep, front face on the edge) clears the front deck-3 standoffs by 2 mm. The four corner chamfers are turned square to the ToF brackets: front ±50°, rear ±135°, rear chamfers 30 mm long.
  • Holes: 4 × M4 deck standoffs (±38.09, -121.89 / 107.64), 2 × M3 (±55.26, 84.95), 2 × M3 for the ZED 2i on 5 mm standoffs (±18, 134.9; holes 36 mm apart), 6 ToF bracket footprints ToF_Bracket_M2.5 (two M2.5 holes, flange and screw-head keep-outs), the ZED USB cable cutout 11.1 × 18 mm.
  • Stack (gen/routing.py, gen/autoroute.py): 8 layers. Signals on F.Cu, In2.Cu, In3.Cu and B.Cu; In1 and In6 are GND planes with a GND_MOT island under the motor block (joins GND only at the star tie NT1 next to the battery connector); In4 is one VBUS plane over the whole board; In5 is a split power plane: MOT_BUS over the drive, SERVO_RAW and SERVO_PWR over the servo/arm block, +3V3_MCU under the MCU, +5V everywhere else. The router treats In1/In4/In5/In6 as power layers (vias only). The battery chain (3 mm) and the 5-10 A nets (2 mm) run on the outer layers only; 2 oz outer copper is assumed. Local pours that would trap other nets' pads are filled after routing.
  • 667 footprints: 411 on the top, 256 on the bottom. 613 assembled placements (361 top, 252 bottom; 589 SMT, 24 THT), 46 mechanical or copper-only, 1 module (the Pi), 7 DNP. 159 BOM lines (unique LCSC numbers), 47 ICs, 433 nets.
  • DNP: the PH/EN MODE 0R R1106/R1206; the second ITRIP line Q1102/Q1202 and R1151; the IMU CLKIN link R423/R424. Everything else, including the MMC5983MA and the bottom THT XT30s, is assembled by JLC (owner, 2026-10-10).
  • Stock (gen/stock.py, 2026-10-11, 2 boards): all 159 lines in JLC stock with at least 3× the need, so one JLC order with no Global Sourcing. Thinnest: Würth 2×20 C7433390 (89), PCA9685 (157), RT0603 549 Ω 0.1 % (224), STM32G474 (248), TPS259470A (331), EEHZK1E471P (404), DRV8243 (408).

Blocks and placement (after placement.json)

WhereTopBottom
Rear right, X 34..58, Y -112..-34Power entry (rev B): XT60 J1, F1 15 A, LM74800 latch, 2 mΩ battery shunt + INA238 0x40, VBUS bulk; motor-bus F2, 5 mΩ shunt shared by the LM5069 and INA238 0x41, BSC010N04LS, LM5069-1—
Rear centre, Y -120..-772 × 220 µF MOT_BUS bulk at the drivers; brake chopper (rev B); D10 TVS; D31 B540C freewheel diodeDRV8243H L/R at (-20.5 / 25.5, -83) with straps, ITRIP ladder, IPROPI and NTC; motor PH-6 J41/J42 at (∓7, -84) between the motors' rear ends with an empty ≥ 8 mm band for the OUT pours; TMP117 0x48; ToF ports J63-J65 (Y -110..-112)
Tail, Y -158..-120STM32G474 at (-13, -135) with crystal, LDO, TC2030, the E-stop NAND/ALIVE logic, IPROPI clamps; USB-C J50 + TPS2121 + USBLC6 at the rear edge right of the rear ToF bracket; CAN (TCAN1044AV, GH-4 J51, split termination) at the rear-left edge; rear bumper J14—
Left strip, X -70..-40E-stop XH-4, fan 2, spare 5 V XH-2, Pi power USB-C J53, fan 1Jetson and spare-VBAT TPS16630 (U5, U7), TVS; XT30 J21/J20 at X -65, Y -35/-48 (bottom, mating downward)
Y -57..-33IMU at (-14, -46)—
Middle, Y -30..25Raspberry Pi 4 on 4 × M2.5 at (13, -4); no top parts under iteFuse row under the Pi at Y -2 (fans ×2, spare 5 V, Pi USB-C) and the encoder eFuse U78 (28, 3); PCAL6524 0x22/0x23 (U37/U38) with their arrays; TCA9548A (0, 14) and TCA6416A (12, 14); ADS7128 U35 (43, 8) / U36 (43, -8) + REF3425; OVLO dividers
Front, Y 26..69Pi 2×20 header at Y 30.2 next to the Pi's own header; 5.17 V buck + INA238 0x47 and the servo buck 6.0/7.4 V + INA238 0x43; F3/F4; VBUS polymer; TMP117 0x49 between the bucksTPS62826 3.3 V ToF rail
Front, Y 69..156Lidar XH-5 ×3, RTC + CR1220, buzzer, button, xArm block (TPS259470L U88, TLV76050, BSS138 shifter, 220 µF, PH-3 ×2), steering eFuse U83 + B540C + 2 × 470 µF, PCA9685 0x60, 8 servo headers, front bumper, MMC5983MA, ZED 2i standoffs, SK9822 ×8 along the front edge with the AHCT buffersLidar eFuses ×3, lidar UART resistors and ESD; ToF ports J60-J62

Layer rules:

  • Tall parts only on the top: inductors, polymers, THT headers.
  • check_netlist.py checks bottom heights: at most 8 mm over the motors (Y -60..-130), at most 10 mm elsewhere; nothing on the top under the Pi.
  • Floorplan rules (data/pcb-revc/review/floorplan-2026-10-11.md): ≥ 2 mm free ring around 0.5 mm QFNs, 3 mm around the LQFP-64, no logic-GND parts over GND_MOT.

Renders: renders/top_labelled.png, renders/bottom_labelled.png (seen from below, so mirrored), renders/top.png, renders/bottom.png, renders/iso.png; re-render after routing.

What changed against the first rev C netlist (10-11 October)

  • Vertical connectors only (owner): USB-C J50/J53 GCT USB4115-03-C, CAN GH-4 JST BM04B-GHS-TBT, ToF GH-6 HCTL HC-GH-6PLT (C3011957, GH-compatible on the JST BM06B land; genuine JST had 1 in JLC stock), XT30 AMASS XT30UPB-F on the bottom, lidar JST B5B-XH-A.
  • ToF: 6 ports, one per printed bracket under deck 2 (front, front ±50°, rear, rear ±135°; gen/tof.json, field of view checked in cad/robot/tof_fov.py), all on +3V3_TOF (the TPS62826 EN is the group switch); the TCA9548A is alone on the Pi's I2C6 (GPIO22/23, J3 pins 15/16, 2.2 k pull-ups); mux channels 6/7 and TCA6416A P06/P07/P16/P17 are tied off.
  • Simplified (owner, 2026-10-11): no per-port ToF eFuses and no ADS7128 0x10; one eFuse U78 for both encoders; INA238 only on battery 0x40, motor bus 0x41, servo 0x43, 5 V total 0x47. 763 parts before, 667 now.
  • xArm 1S bus on the board: TPS259470L U88 (active current limit, R_ILM 750 Ω = 4.45 A) from SERVO_RAW, OVLO on the steering eFuse's divider (61.9k/10k = 8.63 V); STM32 PB9 USART3_TX AF7 single-wire half-duplex -> BSS138 -> 5 V bus (390 Ω 1206, TPD1E10B09), 2 × PH-3; ARM_PWR bleed 4.7 kΩ. The round-1 TLV6700 cut and the TPS259824L (0 at JLC) are gone.
  • MCU: MCU_ALIVE PC3 (pin 11), PB9 = arm UART, PA6 = USB VBUS detect, PA4 reads DRVOFF through 10 kΩ, nSLEEP pull-downs 4.7 kΩ, IMU CLKIN held low by 100 kΩ.
  • Pi power through USB-C J53: U87 is the auto-retry TPS259470A (R_ILM 887 Ω = 3.76 A), EN 100k/100k from +5V (2.6 V), not on the expander; Rp 10 kΩ (3.0 A); ribbon pins 2/4 open.
  • Polarity: XT60 J1 and XT30 J20/J21 pad 1 = GND at the chamfered end ('-'), pad 2 = '+' (round 1 F-1/F-2).
  • MOT_BUS_OFF (0x22 P2_4) pulled up to +3V3_MCU, not +3V3_PI: the motor bus stays off when the Pi is dead or unplugged (round 1 P-4).
  • C26 (button debounce) to BAT_F: plugging the battery in no longer latches the board on (round 1 P-2).
  • Series resistors to the Pi (E-stop, UART0 RX, lidar UARTs) 100 Ω -> 1 kΩ (back-powering).
  • Board grown and re-floorplanned for routing; ZED 2i on two M3 standoffs on the board.

Kept from rev B

  • The LM74800 switch and latch, F1, the battery path, NT1 (star ground) and the brake chopper.
  • The LM61495 buck block.
  • The STM32 core: crystal, decoupling, BOOT0/NRST from the Pi, LDO.
  • The E-stop NAND/ALIVE logic driving DRVOFF.
  • RTC, button and bumpers.

Removed against rev B

  • DRV8316, the BLDC phase, Hall and encoder connectors; the RoboClaw fallback (JP1, JP2, J48, J49).
  • TPS73733, the rev B ToF wiring and the Jetson UART; the INA226s; the DRV8316 footprint.

Custom footprints (gen/footprints.py)

FootprintPartNote
TI_RXY0014A_VQFN-HR-14_3x4.5mmDRV82434 thermal vias in the GND bar; mask polygons approximated
TI_RPW0010A_VQFN-HR-10_2x2mmTPS259470L/A—
TI_DMQ0006A_VSON-HR-6_1.5x1.5mmTPS62826pads from drawing labels
TI_RUX0012A_VQFN-HR-12_2x2.5mmTPS2121pads from drawing labels
TI_DPY0002A_X1SON-2TPD1E10B09pads 0.3 × 0.5 at ±0.35 (TI p.19)
LED_SK9822-EC20_2x2mmSK9822-EC20partly illegible drawing
ToF_Bracket_M2.5ToF bracketholes, flange keep-out under the board, screw heads on top
rev B: TI_RPH0016B, TI_DRR0012E, NANO2 fuse, Kelvin 2512 shunt, NetTie, Pi standoffs

PCAL6524 uses the KiCad QFN-32-1EP_5x5mm_P0.5mm_EP3.1x3.1mm, close to but not the NXP HUQFN32 land.

Deviations from the JSON files and substitutions

  1. Battery shunt. Vishay WSLP25122L000FEA (2512, 2 mΩ, 3 W, C2090981) instead of the WSLP2726: same value, fits the rev B Kelvin land.
  2. ITRIP default 2.41 A. Series ladder 8.25k / 13.7k / 25.5k; ITRIP_SEL is pulled up (R1150 to +3V3_MCU), so 2.41 A applies by default and in MCU reset; the STM32 drives PB11 low for 4.05 A; with R1111/R1211 removed and PB11 low, 4.73 A. drv8243.json synced on 2026-10-11.
  3. Motor bus off by default. MOT_BUS_OFF (0x22 P2_4) has its pull-up (RN array) to +3V3_MCU; Q31 holds the LM5069 UVLO low until the Pi drives the line low.
  4. Expander reset. EXP_RESET_N (GPIO6, 10 kΩ pull-down) resets both PCAL6524s and the TCA6416A: every switched load stays off until the Pi drives it high. The TCA9548A has its own reset (GPIO19, 10 kΩ pull-up).
  5. STM32 PA6 is USB_VBUS_DET (22k/33k). TPS2121 ST goes to a test point (no MCU pin left).
  6. ILM readback through 10 kΩ at the eFuse, 1 nF only at the ADS7128 input (§11a).
  7. Pi USB-C eFuse U87 (Q47 -> C32): TPS259470A auto-retry, R_ILM 887 Ω; 0x23 is full, so its FLT and current go to ADS7128 0x17 AIN4 (as GPIO, pulled up to ADC_AVDD) and AIN3. The arm eFuse U88 uses AIN5 (current) and AIN6 (FLT) the same way.
  8. ToF rail enable from 0x22 P2_5 with a pull-down; PG to 0x23 P2_6.
  9. TCAN1044AV VCC from +5V_MCU, so CAN works on USB power alone. CAN connector pin 1 = +5V_AUX (spare 5 V eFuse).
  10. SK9822 supply straight from +5V.
  11. Servo bulk 2 × Panasonic EEHZK1E471P (470 µF 25 V, C242138).
  12. TPS16630. Jetson: MODE = GND (auto-retry), 5.1k = 3.53 A, SHDN through Q7 from GPIO25. Spare output: latch-off, 4.7k = 3.83 A, SHDN 10 kΩ pull-down. Their currents come from the TPS16630 IMON pins (ADS7128 0x17 AIN1/AIN2); the separate INA238 0x44/0x45 and shunts are gone.
  13. Fan PWM through a 2N7002K (fans pull PWM up to 5 V): inverted in firmware.
  14. LM5069 freewheel diode B540C on the GND_MOT island at the bulk capacitors.

Open issues and what could not be verified

Tracked in docs/open-issues.md (Q49 layers, M25-M27 and M29-M30 cable and connector checks, P24-P28). In short:

  • Mechanical: room for the mated PH plug in the gap between the motors; XT30 tails and pigtail bend at the left edge (M27); HCTL GH-6 mating with genuine GHR housings (M29).
  • Footprints: DRV8243 mask polygons approximated; TPS62826, TPS2121, SK9822 pads from drawing labels; XT30 drill 1.8 mm vs AMASS 1.9 mm; no 3D models for the new footprints; rabbit-body-c.kicad_dru still names the old USB4105 for J50.
  • Pinouts: TPD4E05U06 pins from memory; PESD2CANFD24V unchecked; pin 1 of the kit motor cable, the C1 lidar cable and the xArm cable to be checked with a meter; XT polarity on the moulded housings.
  • Electrical: DRV8243 thermals assume 2 oz outer copper and via-stitched pads; ILM readback below 0.5 A unspecified; BSC010N04LS SOA margin under the LM5069 small; ITRIP live switching with a FET ladder untested; +5V worst case 5.30 V vs the C1's 5.2 V (P26); SERVO_RAW unclamped after a buck high-side short (P25); brake resistors 4 × their rating while on (P24); PCA9685 can phantom-power unpowered servos (P27, firmware).
  • Stale text in the generator (not netlist): design.py docstring and comments (9 INA238, 8 ToF, ADS7128 ×3, "+5V17", "56k Rp", PCAL INT on GPIO22, VBUS sense on PC3), the bottom silk "4L 1.6 mm" and the routing.py docstring ("In5 signals") (P28).

Parts

346
QtyValueFootprintReferences
31100nFCapacitor_SMD:C_0603_1608MetricC10, C11, C12, C14A, C14B, C19, C20, C21, C120, C121, C122, C123, C1101, C1102, C1201, C1202 +15
181kResistor_SMD:R_0603_1608MetricR14, R15, R22, R24, R32B, R33B, R36, R48, R86, R91, R100, R101, R102, R103, R104, R105 +2
184.7kResistor_SMD:R_0603_1608MetricR29, R30, R110, R111, R112, R113, R114, R115, R120A, R120B, R121A, R121B, R122A, R122B, R123A, R123B +2
16100kResistor_SMD:R_0603_1608MetricR14B, R18, R23, R25, R26, R43, R61, R63, R87, R96, R97, R98, R401, R404, R601, R604
1610kResistor_SMD:R_0603_1608MetricR9A, R17, R28, R31, R39, R41, R58, R60, R64, R65, R66, R81, R83, R90, R95, R99
13100Resistor_SMD:R_0603_1608MetricR10, R11, R12, R13, R16, R42, R55, R1102, R1103, R1104, R1202, R1203, R1204
121nFCapacitor_SMD:C_0603_1608MetricC100, C101, C102, C103, C104, C105, C1110, C1111, C1112, C1210, C1211, C1212
101uFCapacitor_SMD:C_0603_1608MetricC25, C55, C85, C90, C406, C451, C461, C606, C1107, C1207
1022uFCapacitor_SMD:C_1206_3216MetricC410, C411, C412, C413, C414, C610, C611, C612, C613, C614
810Resistor_SMD:R_0603_1608MetricR701, R702, R711, R712, R721, R722, R731, R732
810uF 50VCapacitor_SMD:C_1210_3225MetricC31, C32, C401, C402, C601, C602, C1103, C1203
710uFCapacitor_SMD:C_0805_2012MetricC4, C6, C7, C9, C13, C1106, C1206
622Resistor_SMD:R_0603_1608MetricR130, R131, R132, R133, R134, R135
6LED redLED_SMD:LED_0603_1608MetricD2, D3, D4, D5, D6, D93
5220Resistor_SMD:R_0603_1608MetricR32, R33, R34, R35, R89
4100nFCapacitor_SMD:C_0402_1005MetricC405, C407, C605, C607
4220uF 35VCapacitor_SMD:CP_Elec_8x10.5C30, C33, C1109, C1209
439R 2WResistor_SMD:R_2512_6332MetricR50, R51, R52, R53
4470nFCapacitor_SMD:C_0603_1608MetricC403, C404, C603, C604
4AO3400APackage_TO_SOT_SMD:SOT-23Q3, Q5, Q7, Q8
4INA226Package_SO:MSOP-10_3x3mm_P0.5mmU19, U20, U21, U22
4SMBJ20ADiode_SMD:D_SMBD1, D10, D13, D14
4ToFConnector_JST:JST_PH_B5B-PH-K_1x05_P2.00mm_VerticalJ8, J9, J10, J11
4deck standoff M4MountingHole:MountingHole_4.3mm_M4H1, H2, H3, H4
310nFCapacitor_SMD:C_0603_1608MetricC8, C24, C86
322kResistor_SMD:R_0603_1608MetricR44, R405, R605
210Resistor_SMD:R_0805_2012MetricR451, R461
210mR 1Wrabbit_body:R_Shunt_2512_KelvinR2, R4
210pFCapacitor_SMD:C_0603_1608MetricC408, C608
2150kResistor_SMD:R_0603_1608MetricR40, R82
218pFCapacitor_SMD:C_0603_1608MetricC88, C89
21uFCapacitor_SMD:C_0402_1005MetricC1104, C1204
222Resistor_SMD:R_0402_1005MetricR1101, R1201
23.3uHInductor_SMD:L_Coilcraft_XAL1010-XXXL4, L6
2330Resistor_SMD:R_0603_1608MetricR27, R40A
239kResistor_SMD:R_0603_1608MetricR406, R606
24.7uFCapacitor_SMD:C_0603_1608MetricC84, C91
24.99kResistor_SMD:R_0603_1608MetricR403, R603
247kResistor_SMD:R_0603_1608MetricR45, R47
247nFCapacitor_SMD:C_0603_1608MetricC23, C80
247nFCapacitor_SMD:C_0402_1005MetricC1105, C1205
25Arabbit_body:Fuse_Littelfuse_NANO2_451_2410F3, F4
2BSC010N04LSPackage_TO_SOT_SMD:TDSON-8-1Q1, Q2
2DRV8316CRrabbit_body:TI_RGF0040E_VQFN-40_5x7mm_P0.5mm_EP3.7x5.7mmU11, U12
2GNDTestPoint:TestPoint_THTPad_D1.5mm_Drill0.7mmTP6, TP7
2HallsConnector_JST:JST_PH_B5B-PH-K_1x05_P2.00mm_VerticalJ43, J44
2LM61495rabbit_body:TI_RPH0016B_VQFN-HR-16_3.5x4.5mmU4, U6
2NTC 10kResistor_SMD:R_0603_1608MetricRT65, RT66
2deck standoff M3MountingHole:MountingHole_3.2mm_M3H5, H6
2encoderConnector_JST:JST_GH_BM07B-GHS-TBT_1x07-1MP_P1.25mm_VerticalJ45, J46
2motor phasesConnector_Molex:Molex_KK-396_A-41791-0003_1x03_P3.96mm_VerticalJ41, J42
1+3V3_MCUTestPoint:TestPoint_THTPad_D1.5mm_Drill0.7mmTP10
1+3V3_TOFTestPoint:TestPoint_THTPad_D1.5mm_Drill0.7mmTP5
1+5VTestPoint:TestPoint_THTPad_D1.5mm_Drill0.7mmTP2
11.5MResistor_SMD:R_0603_1608MetricR59
11.5kResistor_SMD:R_0603_1608MetricR37
115Arabbit_body:Fuse_Littelfuse_NANO2_451_2410F1
11MResistor_SMD:R_0603_1608MetricR49
11N4148WSDiode_SMD:D_SOD-323D9
11uFCapacitor_SMD:C_0805_2012MetricC82
12.2uFCapacitor_SMD:C_0603_1608MetricC18
120kResistor_SMD:R_0603_1608MetricR602
1220kResistor_SMD:R_0603_1608MetricR46
124kResistor_SMD:R_0603_1608MetricR402
12mR 3Wrabbit_body:R_Shunt_2512_KelvinR1
13.9kResistor_SMD:R_0603_1608MetricR84
133kResistor_SMD:R_0603_1608MetricR62
1470uF 16VCapacitor_THT:CP_Radial_D8.0mm_P3.50mmC14
15.1kResistor_SMD:R_0603_1608MetricR94
15mR 3Wrabbit_body:R_Shunt_2512_KelvinR3
160.4kResistor_SMD:R_0603_1608MetricR57
168kResistor_SMD:R_0603_1608MetricR80
18Arabbit_body:Fuse_Littelfuse_NANO2_451_2410F2
18MHzCrystal:Crystal_SMD_3225-4Pin_3.2x2.5mmY1
1BAT54SPackage_TO_SOT_SMD:SOT-23D12
1BAT_FTestPoint:TestPoint_THTPad_D1.5mm_Drill0.7mmTP12
1BSC026N04LSPackage_TO_SOT_SMD:TDSON-8-1Q6
1BZT52C12Diode_SMD:D_SOD-123D11
1BZT52C8V2Diode_SMD:D_SOD-123D8
1CR1220Battery:BatteryHolder_Keystone_3000_1x12mmBT1

The 305 most common of 346 parts.

More from seralexeev/rabbit

3
  • 8 layers140 × 314.2 mmRabbit body c, the printed circuit board in 3D

    Rabbit body c

    seralexeev/rabbit

    rabbit source code

    673 parts1
  • 4 layers179.4 × 134.6 mmRabbit board, the printed circuit board in 3D

    Rabbit board

    seralexeev/rabbit

    rabbit source code

    61 parts1
  • 2 layers22 × 18 mmRabbit tof, the printed circuit board in 3D

    Rabbit tof

    seralexeev/rabbit

    rabbit source code

    22 parts1

Similar boards

  • 4 layers74 × 90 mmBay node, the printed circuit board in 3D

    Bay node

    kartben/hw-testing-rack

    3D-printed, tilted test shelf for 16 dev boards: sliding drawers, per-bay ESP32-S3 running Zephyr (USB/IP, power switching, metering), KiCad PCBs, OpenSCAD parts, BOM and an interactive 3D viewer

    135 parts
  • 4 layers64.2 × 89.1 mmStarBridge Adapter, the printed circuit board in 3D

    StarBridge Adapter

    luishutterli/starbridge

    To make it easy for you to get started with GitLab, here's a list of recommended next steps.

    68 parts
  • 4 layers101.6 × 50.8 mmBuck Conveter PCB, the printed circuit board in 3D

    Buck Conveter PCB

    TrickfireRobotics/circuit-schematics

    A repo for storing some of TrickFire's circuit schamtics, diagrams, and other related circuit files

    23 parts
  • 2 layers90.1 × 30 mmIntegrated vil rml, the printed circuit board in 3D

    Integrated vil rml

    SCFormulaElectric/USC-Electrical-Systems

    32 parts9
  • 2 layers58 × 68 mmLight PCB, the printed circuit board in 3D

    Light PCB

    oudehm/seniorDesignPCB

    Editable KiCad projects for the brain, light, power, and pump boards.

    27 parts
  • 4 layers67.4 × 67.4 mmSCLF Gripper, the printed circuit board in 3D

    SCLF Gripper

    Tknika-SCLF/sclf-gripper

    Deskargatu eta instalatu Antigravity bere webgune ofizialetik. VSCode/Windsurf-en fork bat da eta modu berean funtzionatzen du.

    78 parts1
  • 2 layers350 × 235 mmDogrudan sdr C, the printed circuit board in 3D

    Dogrudan sdr C

    kocer/direct-sampling-sdr

    Direct-sampling SDR transceiver with four phase-coherent channels, and a class-A power amplifier for 1.8 to 54 MHz.

    406 parts1

Questions

How big is the Rabbit body PCB?

It measures 120.5 × 269.9 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Rabbit body use?

346 parts, built around the INA226AIDGSR, DRV8316CRRGFR, LM61495RPHR and AO3400A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Rabbit body KiCad files?

From the seralexeev/rabbit repository on GitHub, at the commit this page was made from: the board is pcb/rabbit-body/rabbit-body.kicad_pcb and its schematic pcb/rabbit-board/rabbit-board.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Rabbit body design in my own project?

Its repository states no licence, so its author keeps all rights: ask seralexeev before reusing the design.