
SuperPower RPi KiCAD
SensorsIot/SuperPower
Here you should find the best power supplies for your low-power projects
quick and dirty lipo + neopixel flasher making use of parts on hand
Attiny neopixel flasher is an open-source printed circuit board by securelyfitz, from the securelyfitz/attiny-neopixel-flasher repository on GitHub. It is a 2-layer board of 58 × 45 mm with 7 parts on 5 nets, routed with 22 tracks and 0 vias.
It is built around the ATTINY85-20SU. Its parts include 1 resistor, 1 IC, 1 connector and 1 switch. It belongs with the lEDs and displays boards and the AVR (ATmega, ATtiny) boards of this library.
quick and dirty lipo + neopixel flasher making use of parts on hand
Power provided by a lipo battery using a 1mm pitch 4-pin jst connector. Power connects to the ATTINY85 and neopixels Button connects to reset - the ATTINY keeps track of which pattern it's on in eeprom, and plays the next one at reset.
WS2182's consume 1mA when off, discharging the 1000mAh pack in a day, so now I power them with ATTINY GPIO pins. ATTINY GPIO pins provide max 40mA each 60mA combined, so I scratched off the trace and soldered a bodge wire to two pins (2+3) and the vcc pin of the neopixel ring
Using all built-in footprints, manually placed 1x1 headers for connection to the 16-neopixel rings i have on hand. Optimized for milling with fat bits, so i removed pins 2,3,6,7 from the attiny footprint. Still need to use a V bit to get the space between the power connector pins but the rest is 1/32" flat end. Sized to match the batteries i had lying around.
Based on adafruit's neopixel strandtest with minor additions:
| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | Conn_01x01 | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | DATA1, GND1, VCC1 |
| 1 | ATtiny85-20SU | Package_SO:SOIJ-8_5.3x5.3mm_P1.27mm | U1 |
| 1 | Conn_01x04_MountingPin | Connector_JST:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal | J1 |
| 1 | R | Resistor_SMD:R_1206_3216Metric | R1 |
| 1 | SW_MEC_5E | Button_Switch_THT:SW_TH_Tactile_Omron_B3F-10xx | SW1 |

SensorsIot/SuperPower
Here you should find the best power supplies for your low-power projects

KivApple/dell-charger-emulator
Emulator of original Dell charger using ATTINY85


bwack/C64-Saver-bwack
C64 Saver v1 and v2 - Overvoltage protection for the C64 and its power brick.


valerionew/very-good-uc-doggos
A special graduation present for a special friend. Six microcontrollers in one devboard


spielhuus/LoRa-Environmental-Sensors
ATtiny85 based LoRa atmospheric sensor board with BME280
It measures 58 × 45 mm and has 2 copper layers, 1.6 mm thick.
7 parts, built around the ATTINY85-20SU. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the securelyfitz/attiny-neopixel-flasher repository on GitHub, at the commit this page was made from: the board is hardware/attiny-neopixel-flasher.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask securelyfitz before reusing the design.