Skip to the content
2 layers48.3 × 48.3 mmShutter speed tester, the printed circuit board in 3D

A project which goal is to design and build a tool that allows to test the shutter speed accuracy of a film camera

Size
48.3 × 48.3 mm
Copper layers
2
Thickness
1.6 mm
Parts
17
Nets
13
Pads
63
Tracks, vias
88, 0
Pours
2
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
23 May 2020
Updated
2 Sep 2026

Overview

Shutter speed tester is an open-source printed circuit board by sebastienroy, from the sebastienroy/shutter_speed_tester repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 48.3 × 48.3 mm with 17 parts on 13 nets, routed with 88 tracks and 0 vias.

It is built around the PN2222A. Its parts include 5 resistors, 4 connectors, 1 diode, 1 transistor and 1 switch. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

1

README

README.md

Shutter Speed Tester for Film Cameras

The shutter speed tester is a project which goal is to design and build a tool that allows to test the shutter speed accuracy of a film camera

Shutter Speed Tester for Film Cameras in FreeCAD

When people passionated with old film cameras want to use their camera to shoot film, this sometimes results in an over or an under exposed film.
This is usually due to the speed of the camera shutter that is not any more accurate. In order to check the shutter speed accuracy, the camera owner has to compare the actual opening time of the shutter with the expected one.
This is the purpose of the shutter speed tester : measure the accuracy of shutter speed.

Here is a presentation video (in French) :

Presentation video in french

The result of this open source project is to allow anyone who has the minimum skills in DIY domain to build his own device

Here is the description of the open source project.

Accuracy of the open source tester

The resulting tester has been tested against two methods described in shutter meta tester project : time slot method and rotating wheel method.
With the time slot method (an LED lit during a given time duration), the difference between expected and measured value is about a few tens of microseconds. This error is due mainly to the latency of the phototransistor. This error is small enough to not to be taken into account even at speed up to 1/2000s.
With the rotating wheel method, we can observe an error a lot bigger. This error is not due to electronic factors, but results from geometric facts:
The sensor of the tester is a bulb of 3mm diameter.
At 1/1000s, given that the curtains translation speed is about 3m/s, the slit width of the curtain shutters is about 3mm large.
When trying to measure a 3mm object with a 3mm sensor, the resulting error is about 100%.
So, because of geometric consideration, the use of such a tester should be reserved for speeds not exceeding 1/250.
The conclusion is the same for all testers with a similar sensor that do not provide a calibration mechanism.

Baby Shutter Tester mark II

Many people, interested to get such a device but who don't feel skilled enough to build their own copy, asked the author of the project to build it for them.
This resulted to the commercial version of the tool, the Baby Shutter Tester (mark I).
The Baby Shutter Tester was regularly improved, and its main additional feature was the ability to self calibrate. The self-calibration mechanism allowed a precision of a few microseconds, instead of 1 stop at high speeds.
However, the precision brought by the self-calibration procedure required to follow a very specific process, difficult to implement outside a workshop.

So, a completely reworked version has been designed: the Baby Shutter Tester Mark II.
The speed measurement method impleted by this new version is completely different: instead of starting a timer at a given light illumination threshold, the tester takes into account all the light variations that hits its sensor.
This allows to take into account high speed ranges, where the shutter cannot be considered as a perfect shutter, i.e. the cases where the shutter cannot be aproximated to an on/off mechanism.
This method is similar to the method used by the Kyoritsu legacy professional shutter tester.
Details about the measurement method can be find here:
https://photographyelectronics.com/methods-for-measuring-shutter-speed/
The experimental results that confirm the accuracy of the method and of the electronic circuits of the Baby Shutter Tester mkII can be read here;
https://photographyelectronics.com/experimental-measurement-of-the-shutter-speed-of-a-leaf-shutter/

In addition, the Baby Shutter Tester Marks II meets all the recommendations of the ISO-516:2019 standard. Not only the testing method but also all the measurement precision requirement described by the standard.

The benefits of this characteristics are the following:

  • An extreme accuracy
  • The accuracy is obtained without calibration procedure
  • Using the optional light source with diffuser, the tester can also measure central (leaf) shutters without any bias.

More information on https://photographyelectronics.com

Baby Shutter Tester image

Video presentation

Presentation YouTube

Accuracy test methods

The accuracy of the Baby Shutter Tester mark II is checked using

Where to buy

https://photographyelectronics.com/shop/
eBay link

User manual

User Manual

Curtain travel time measurement: The Shutter Lover

The Shutter Lover is a tool specialized in the measurement of the travel time of the curtains of focal plane shutters.
The measurement of the curtain travel time is necessary for camera repairers, in order to be able to ajust the springs of each of the curtains.
The goal is to obtain an homogeneous travel time of the two curtains, with values in accordance with the manufacturer recommendations.

Shop: https://photographyelectronics.com/shop/
This product is also available for purchase on ebay.

Here is a short teaser :
Video of the Shutter Lover

User Manual

User Manual

Test bench

In order to get the better precision and reproducibility with the shutter Lover, it is recommended to use a test bench, such as the one describe here.

Parts

17
QtyValueFootprintReferences
4MountingHoleMountingHole:MountingHole_2.5mmH1, H2, H3, H4
21kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR2, R5
110kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR4
11MResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR3
1220Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR1
1Arduino_Nano_v3.xModule:Arduino_NanoA1
1Control LEDLED_THT:LED_D5.0mmD1
1LCDConnector_Molex:Molex_KK-254_AE-6410-04A_1x04_P2.54mm_VerticalJ4
1Light SensorConnector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_VerticalJ2
1Light sourceConnector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_VerticalJ1
1PN2222APackage_TO_SOT_THT:TO-92_Inline_WideQ1
1PowerConnector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_VerticalJ3
1Reset switchButton_Switch_THT:SW_PUSH_6mm_H5mmSW1

Similar boards

  • 2 layers152.4 × 101.6 mm8088-FE2010A SBC, the printed circuit board in 3D

    8088-FE2010A SBC

    skiselev/micro_8088

    Micro 8088 - IBM XT Compatible Processor Board based on Faraday FE2010 chipset

    72 parts412GPL-3.0
  • 2 layers33.7 × 66 mmSmartbell, the printed circuit board in 3D

    Smartbell

    Staacks/there.oughta.be

    Projects featured on my blog at https://there.oughta.be

    27 parts108GPL-3.0
  • 4 layers100 × 100 mm2063-Z80, the printed circuit board in 3D

    2063-Z80

    Z80-Retro/2063-Z80

    Retro Z80 CPU Board

    86 parts96
  • 2 layers30.7 × 76.1 mmRepeater v2, the printed circuit board in 3D

    Repeater v2

    plusvic/simplebus2-intercom

    General description of the Simplebus2 protocol used by some Comelit's intercoms. Hardware for retransmitting Simplebus2 messages over UART.

    17 parts95CC0-1.0
  • 2 layers28.8 × 43.8 mmAdv pcb, the printed circuit board in 3D

    Adv pcb

    Vail-CW/vail-adapter

    Adapter for cw morse keys to USB

    13 parts81MIT
  • 2 layers23.2 × 52.1 mmOpenC64Saver, the printed circuit board in 3D

    OpenC64Saver

    SukkoPera/OpenC64Saver

    Protect your Commodore 64 from killer power supplies!

    17 parts79
  • 4 layers184.2 × 169.5 mmSB mini II, the printed circuit board in 3D

    SB mini II

    simonboak/SB-mini-II

    A homebrewed Apple II clone

    97 parts76MIT
  • 2 layers49.5 × 30 mmAirpcb smd old, the printed circuit board in 3D

    Airpcb smd old

    issalig/toshiba_air_cond

    AB protocol decoder for toshiba air conditioners

    30 parts65

Questions

How big is the Shutter speed tester PCB?

It measures 48.3 × 48.3 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Shutter speed tester use?

17 parts, built around the PN2222A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Shutter speed tester KiCad files?

From the sebastienroy/shutter_speed_tester repository on GitHub, at the commit this page was made from: the board is design/Kicad_shutter_speed_tester/shutter_speed_tester.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Shutter speed tester design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).