Skip to the content
2 layers75.7 × 50 mmEtapa2.1, the printed circuit board in 3D
Size
75.7 × 50 mm
Copper layers
2
Thickness
1.6 mm
Parts
24
Nets
13
Pads
69
Tracks, vias
172, 2
Pours
1
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
18 Mar 2024
Updated
18 Mar 2024

Overview

Etapa2.1 is an open-source printed circuit board by sebascarmar, from the sebascarmar/pruebasPCB repository on GitHub. It is a 2-layer board of 75.7 × 50 mm with 24 parts on 13 nets, routed with 172 tracks and 2 vias.

It is built around the TL082. Its parts include 6 resistors, 5 connectors, 4 ICs and 1 capacitor.

Main components

1

README

README.md

pruebasPCB

IMPRESION DE FOTOLITO:

text
* Primero se imprime en papel común el circuito en negativo: con ahorro de toner,
con 100 de brillo y 0 de contraste.

* Arriba de esa impresión se pone un pedazo de papel vegetal.

* Se configura la impresora para papel THICK, sin ahorro de toner, 0 de brillo y 110 
de contraste.

* Luego se lo pone ENNEGRECEDOR DE TONER al fotolito de papel vegetal, y se lo deja 
secar.

* En caso de ser necesario, se imprimen 2 fotolitos, ya que la rigidez del papel
vegetal permite alinearlos fácilmente.

FILM:

text
* El film se separa con cinta schotch de forma fácil.

* El film se pone con agua, se alisa y luego se le pone calor. Se cortan los bordes,
se le da un poco más de calor,y se alisa una vez más.

* Se le pone el fotolito, se pone entre vidrios y se cura por 20 seg.

* Se deja por 2 min en el revelador, ayudando con un cepillo.

* Si se ven algunas arrugas en el curado, las pistas saldrán cortadas. Descartar.

ATACADO DE COBRE:

text
* Luego del ataque químico al cobre (5 min), se pone en el removedor durante 2 min
y listo.

MÁSCARA:

text
* Se imprime la máscara de soldado con expansión de 0.3 mm (desde board setup). Debe
ser la misma forma en la que se hizo el fotolito del circuito.

* Se corta De forma tal que le queden "orejas".

* Se corta un pedazo de acetato que tenga orejas más grandes que el fotolito, y se expande 
la pintura lo mejor posible.

* Se pega delicadamente el fotolito al acetato de ambos lados de las orejas, de forma que 
quede BIEN ALINEADO.

* Se cura durante 4 minutos, tiempo suficente para poder sacarla y limpiarle la 
máscara no curada (la de los pads). 

* Luego se puede dejar curando el tiempo que sea necesario.

* Se recomienda usar guantes, la máscara uv cuesta sacarla.

SERIGRAFÍA:

text
* Imrpimirla en una hoja común.

* Cortarlo de manera que le queden dos "orejas".

* Se alinea con la placa, y de una de las orejas se pega a la placa.

* Con quitaesmalte ALGABO amarillo, mojar la placa y poner la hoja encima de la misma

* Durante 2 minutos, dejando siempre mojado, y presionar con rodillo y dedos.

* Retirar el papel estando aun mojado el papel.

Parts

24
QtyValueFootprintReferences
510kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR1, R3, R4, R5, R6
3TL082Package_DIP:DIP-8_W7.62mmU1, U2, U4
1
1100kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR2
110kPotentiometer_THT:Potentiometer_Bourns_3296W_VerticalRV1
110nCapacitor_THT:C_Disc_D6.0mm_W2.5mm_P5.00mmC1
150kPotentiometer_THT:Potentiometer_Bourns_3296W_VerticalRV2
1Conn_VinConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ2
1Conn_VinDCConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ1
1Conn_VoutConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ5
1Conn_VoutDCConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ4
1Conn_VoutIntegConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ3
1PinHeader_1x01_P2.54mm_VerticalConnector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_VerticalJumper
1TL431LPPackage_TO_SOT_THT:TO-92_InlineU3

The 20 most common of 24 parts.

Similar boards

  • 4 layers99 × 53.3 mmPSLab, the printed circuit board in 3D

    PSLab

    fossasia/pslab-hardware

    PSLab Hardware Design and Schematics https://pslab.io

    199 parts1.7kApache-2.0
  • 2 layers82.1 × 82.1 mmUncut Gem, the printed circuit board in 3D

    Uncut Gem

    QuantumVillage/UncutGem

    A prototype Full Stack fully Open Source NV Center Diamond Magnetometer

    207 parts210AGPL-3.0
  • 2 layers96.8 × 97 mmPsoc5power, the printed circuit board in 3D

    Psoc5power

    profdc9/DRSSTC-PCB-Pack

    A pack of PCBs for a dual resonant solid state tesla coil setup. Pretty much everything you need.

    133 parts59
  • 2 layers130.6 × 112 mmSWN, the printed circuit board in 3D

    SWN

    4ms/SWN

    Spherical Wavetable Navigator source code

    614 parts43
  • 2 layers48 × 36.5 mmOsillyscope etchable, the printed circuit board in 3D

    Osillyscope etchable

    tvlad1234/osillyscope

    Low cost, low part count CH32V003-based oscilloscope

    31 parts30MIT
  • 2 layers60 × 50 mmEurorack volca, the printed circuit board in 3D

    Eurorack volca

    grappendorf/eurorack-volca

    Mounting Korg Volcas into a Eurorack system

    25 parts19
  • 2 layers79 × 107 mmEurorack spinfx, the printed circuit board in 3D

    Eurorack spinfx

    grappendorf/eurorack-spinfx

    Spin FV-1 based effects module for Eurorack systems

    80 parts16
  • 2 layers167.8 × 200.6 mmRandom Jazz Generator, the printed circuit board in 3D

    Random Jazz Generator

    telec16/modular-synth

    Little side project, don't expect much updates.

    132 parts16

Questions

How big is the Etapa2.1 PCB?

It measures 75.7 × 50 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Etapa2.1 use?

24 parts, built around the TL082. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Etapa2.1 KiCad files?

From the sebascarmar/pruebasPCB repository on GitHub, at the commit this page was made from: the board is Etapa2.2_Modificada/Etapa2.2/Etapa2.1.kicad_pcb and its schematic Etapa2.2_Modificada/Etapa2.2/Etapa2.1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Etapa2.1 design in my own project?

Its repository states no licence, so its author keeps all rights: ask sebascarmar before reusing the design.