Skip to the content
2 layers14 × 80 mmJoule Candle, the printed circuit board in 3D

Joule Thief Holiday Candle PCB

Size
14 × 80 mm
Copper layers
2
Thickness
1.6 mm
Parts
7
Nets
7
Pads
20
Tracks, vias
22, 2
Pours
2
Routed
Yes
KiCad
KiCad 4
Created
1 Oct 2017
Updated
8 Jan 2018

Overview

Joule Candle is an open-source printed circuit board by sdp8483, from the sdp8483/Joule_Candle repository on GitHub. It is a 2-layer board of 14 × 80 mm with 7 parts on 7 nets, routed with 22 tracks and 2 vias.

It is built around the BC817-40 and SRF4532-510Y. Its parts include 1 resistor, 1 diode, 1 transistor, 1 switch and 1 inductor.

Main components

2

README

README.md

Joule Thief Candle

Original Blog Post

Repository Links

BOM

Below is the BOM for assembling a Joule Thief Candle. Similar 0603 resistors and 3mm LEDs can be substituted for the parts listed below if not available.

DescriptionReferenceValueManufactureMfg Part NumberSupplierSupplier Part Number
BATTERY CONTACT AA SIZEBT1AAMemory Protected DevicesBK-92DigikeyBK-92-ND
RES SMD 6.8K OHM 5% 1/10W 0603R16.8KYageoRC0603JR-076K8LDigikey311-6.8KGRTR-ND
Warm White 3mm LEDD1LEDChanzon100F3T-PT-WH-WWAmazonB01BTYHOLS
TRANS NPN 45V 0.8A SOT-23Q1BC817-25Micro CommercialBC817-25-TPDigikeyBC817-25-TPMSCT-ND
CMC 51UH 200MA 2LN 2 KOHM SMDL1SRF4532-510YBournsSRF4532-510YDigikeySRF4532-510YCT-ND
SWITCH SLIDE SPDT 100MA 12VS1SPDTC&KOS102011MA1QN1DigikeyCKN9559-ND

Consumables

Below is a list of consumable items used during assembly and cleaning. Note that the exact consumable is not necessary, similar items can be substituted as needed.

DescriptionMfg Part NumberManufactureSupplierSupplier Part Number
Lead Free Solder PasteSMD291SNL50T3Chip QuikDigikeySMD291SNL50T3-ND
Lead Free Solder Wire4944-112GMG ChemicalsDigikey473-1251-ND
Rosin Flux835-100MLMG ChemicalsAmazonB005DNR01Q
Flux Cleaner4140-PMG ChemicalsAmazonB005T8KKJY
Paper WipesTP

Tools

Below is a list of tooling used during assembly with part number of the tools I used, note that the exact tool is not needed and similar tools can be substituted as needed.

  • Temperature Controlled Soldering Iron: Hakko FX-888D with T18-D16 tip
  • SMD Hot Air Re-flow Station: X-Tronic 4000 Series
  • Flush Cut Wire Cutters (side cutters?)
  • Anti Static Brush
  • Xacto Knife
  • Fine Tip Tweezers
  • Syringe: Monoject 412

3D Printed Assembly Tooling

Below is a list of 3D printed tooling that is useful during assembly. This tooling is not necessary for small assembly batches but becomes very useful if assembling 10 or more units at a time. 3D model files and STL files for printing are linked down below.

*The modified vise jaws fit the Yet ANOTHER Machine Vise by TheGoofy

Assembly Instructions

  1. Using the Xacto knife or other fine tipped instrument apply a small amount of solder paste to the pads for the NPN transistor and the 6.8K resistor. Less solder paste is better. Buy a stencil next time!
  2. With a pair of tweezers place the transistor and resistor on the pads.
  3. Turn on the re-flow solder station hot air gun with moderate to high air flow.
    • For lead free solder a hot air temperature of about 410C is good for all SMD parts.
    • For lead solder a hot air temperature of about 380C is good for all SMD parts.
  4. Apply heat evenly around the transistor and resistor until the solder is shiny and flows. Pin 2 of the NPN transistor seems to be the last pad to flow.
  5. Allow the PCB to cool before applying solder paste to the pads for the SRF4532 common mode choke. Again less is better and buy a stencil next time!
  6. Using a pair of tweezers place the common mode choke on the pads.
  7. Apply heat evenly around the common mode choke until the solder paste is shiny and flows.
  8. Turn on the soldering iron.
    • For lead free solder a soldering iron temperature of about 415C is good for all through hole parts.
    • For lead solder a soldering iron temperature of about 365C is good for all through hole parts.
  9. Using the switch soldering jig solder the slide switch in place. Start with the middle pin and work out. Additional flux is not necessary if you are using rosin core solder.
  10. Using the LED lead cutting guide cut the leads of an inserted 3mm LED flush to the guide using flush cut wire cutters.
  11. Using the LED soldering jig place the PCB into the jig then place the LED into the jig near the solder pads for the LED. Notice that the orientation indicator of the LED requires that the LED only fits in one orientation on the jig. Solder the LED to the PCB.
  12. Place the battery clips into the PCB, the clips will stay in place.
  13. Place the PCB into the modified vise jaws. Apply a few drops of rosin flux to the battery terminal solder pins and pads.
  14. Solder the battery clips into place. The battery clips will act like heat sinks and require the soldering iron tip to be applied a few seconds longer then normal before applying solder.
  15. Allow the PCB to cool completely.
  16. Place the assembled PCB into a small amount of the flux cleaner and let is soak for a minute or two.
  17. Remove from the flux cleaner and use the anti static brush to remove any left over flux.
  18. Place the assembled PCB into a fresh amount of the flux cleaner for only a few seconds.
  19. After removing from the flux cleaner use some paper wipes (toilet paper) to soak up the flux cleaner from the PCB to remove any left over residue. Repeat this step if necessary to remove stubborn residue.
  20. Allow the flux cleaner to completely evaporate before testing with a AA battery.

Other

If you do not want to bother with ordering components and assembly I do sell these on Tindie.

I Sell on Tidie

Parts

7
QtyValueFootprintReferences
1Logo:P-Logo_SmallLOGO
11KResistors_SMD:R_0603_HandSolderingR1
1AABattery:AA_PCB-ClipBT1
1BC817-40TO_SOT_Packages_SMD:SOT-23Q1
1LEDlib_fp:3mm_PCB_EdgeD1
1SPDTSwitches:SPDT_OS102011MA1QN1S1
1SRF4532-510YInductor:SRF4532-510YL1

Similar boards

  • 2 layers20.4 × 64.5 mmJoule thief breakout boards, the printed circuit board in 3D

    Joule thief breakout boards

    sdp8483/joule_thief_breakout_boards

    Breakout Boards for Joule Thief Development

    40 parts
  • 2 layers54.1 × 14.5 mmMulti LED JT V2, the printed circuit board in 3D

    Multi LED JT V2

    sdp8483/Multi-LED_JT_V2

    Multi LED Joule Thief V2

    12 parts4MIT
  • 4 layers100 × 60 mmT1conv, the printed circuit board in 3D

    T1conv

    ajefferies2/t1conv

    100BASE-T1 ↔ 100BASE-TX media converter + dual CAN FD/USB adapter on one board.

    125 parts
  • 2 layersMP Tracker, the printed circuit board in 3D

    MP Tracker

    elektra42/freifunk-open-mppt

    Open hard- and software solar maximum power point tracker

    70 parts89
  • 2 layers44.2 × 32.6 mmWiring, the printed circuit board in 3D

    Wiring

    esp-ebus/ebus-adapter-hardware

    This repo conains KiCAD design of eBUS bus powered (without external supply) adapter to WiFi.

    49 parts44
  • 11 layers74.2 × 29.2 mmSolderingStationPCB, the printed circuit board in 3D

    SolderingStationPCB

    clytle374/Open-T12-Soldering-Station

    This is a clone of the cheap T12 soldering stations, attempting to eliminate the shortfalls of the cheap designs.

    68 parts43GPL-3.0
  • 6 layers69.6 × 46.1 mmCarrier, the printed circuit board in 3D

    Carrier

    KaiPereira/CM5-SODIMM-Carrier

    A fully open source CM5 carrier to turn your Pi into a Jetson in compact SO-DIMM format!

    98 parts29
  • 4 layersIONPAK2, the printed circuit board in 3D

    IONPAK2

    m-labs/ionpak

    A modern, low-cost universal controller for hot-cathode ionization vacuum gauges. (WIP)

    259 parts23

Questions

How big is the Joule Candle PCB?

It measures 14 × 80 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Joule Candle use?

7 parts, built around the BC817-40 and SRF4532-510Y. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Joule Candle KiCad files?

From the sdp8483/Joule_Candle repository on GitHub, at the commit this page was made from: the board is Joule_Candle.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Joule Candle design in my own project?

Its repository states no licence, so its author keeps all rights: ask sdp8483 before reusing the design.