Skip to the content
11 layers74.2 × 29.2 mmSolderingStationPCB, the printed circuit board in 3D

This is a clone of the cheap T12 soldering stations, attempting to eliminate the shortfalls of the cheap designs.

Size
74.2 × 29.2 mm
Copper layers
11
Thickness
1.6 mm
Parts
68
Nets
60
Pads
203
Tracks, vias
423, 224
Pours
3
Routed
Yes
KiCad
KiCad 8.99 (file 20240706)
Created
15 May 2024
Updated
11 Oct 2024

Overview

SolderingStationPCB is an open-source printed circuit board by clytle374, from the clytle374/Open-T12-Soldering-Station repository on GitHub, published under the GPL-3.0 licence. It is an 11-layer board of 74.2 × 29.2 mm with 68 parts on 60 nets, routed with 423 tracks and 224 vias.

It is built around the LMR50410Y5FQDBVRQ1, B140-E3 and B2B-XH-A, with the BC817-40, PB-09N23P-03Q and PEC11R-4225F-S0024 among its other parts. Its parts include 20 capacitors, 18 resistors, 12 connectors, 4 ICs and 4 diodes. It belongs with the STM32 boards of this library.

Main components

7

README

README.md

Open-T12-Soldering-Station-

This is a clone of the cheap T12 soldering stations, attempting to eliminate the shortfalls of cheap. Useless without the fine firmware from https://github.com/deividAlfa/stm32_soldering_iron_controller

It has provisions for a backup battery. Jumper selectable between internal and external NTC as some of the new handles don't contain a NTC, so this gives you the option if you don't want to add one to your handle. There are also jumper option for configuring different soldering handles. It is setup to use the 1.3” 6 pin OLED display.

The pinouts match the KSGER stations for compatibility with the above mentioned handles. There is no provision for the real time clock in the firmware, I see it as useless.

Some of the cheap boards had issue with the linear voltage regulator dropping out from thermal protection as the power was quite high dropping from 24V to 3.3V. This design uses a switching regulator to step down from 24V ot 5V, and then a 3.3V linear regulator for a clean 3.3V supply.

Much more information on the many models out there at the above mentioned site for the firmware. I created this as it is impossible to tell exactly what you are buying from the suppliers.

Alt text

Alt text

Alt text

Alt text

Alt text

A limited run is available on Tindie.

https://www.tindie.com/products/clytle374/open-t12-soldering-station/

https://www.tindie.com/products/clytle374/open-t12-soldering-station-board-rohs-kit/

Parts

68
QtyValueFootprintReferences
11.1uCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC3, C5, C6, C8, C9, C12, C18, C19, C20, C21, C22
84.7KResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR3, R4, R6, R7, R8, R9, R10, R11
4ConnConnector_PinSocket_2.54mm:PinSocket_1x01_P2.54mm_VerticalJ5, J9, J11, J13
310nCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC7, C10, C11
310uCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC13, C14, C17
3Conn_01x01_PinConnector_PinSocket_2.54mm:PinSocket_1x01_P2.54mm_VerticalJ3, J7, J10
3Jumper_2_Bridgedfootprints:JUMPER_SNIPABLEJP1, JP2, JP4
20Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR17, R18
210uCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC1, C4
21KResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR13, R14
2BAT43W-VDiode_SMD:D_SOD-123D3, D4
110KResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR15
11KResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR1
11uCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC2
1249KResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR16
12KResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR2
14.7KResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR5
1470Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR12
16.8ufootprints:IND_042068_WREL1
1B140-E3Diode_SMD:D_SMAD1
1B2B-XH-Afootprints:CONN_B2B-XH-A_JSTJ4
1B2B-ZRLFSNfootprints:CONN_B2B-ZRLFSN_JSTJ6
1BC817-40Package_TO_SOT_SMD:SOT-23_HandsolderingQ2
1Conn_01x04_PinConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ2
1Conn_01x06_PinConnector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_VerticalJ1
1GX12-5Mfootprints:GX12-5MJ8
1LEDLED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolderD2
1LMR50410Y5FQDBVRQ1Package_TO_SOT_SMD:SOT-23-6_HandsolderingU1
1MCP1825SPackage_TO_SOT_SMD:SOT-223-3_TabPin2U4
1NTC_10KResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderTH1
1OPA336NxPackage_TO_SOT_SMD:SOT-23-5U2
1PB-09N23P-03Qfootprints:PB-09N23P-03Q_MALLS1
1PEC11R-4225F-S0024footprints:SW5_PEC11R-4225F-S0024_BRNSW1
1STM32F103C8TxPackage_QFP:LQFP-48_7x7mm_P0.5mmU3
1TSM150P04LCS_RLGfootprints:TRANS_TSM150P04LCS_RLGQ1

The 67 most common of 68 parts.

Similar boards

  • 2 layers112 × 70.5 mmMacro Pad, the printed circuit board in 3D

    Macro Pad

    Jpwaters09/Macro-Pad

    A 12-key macro pad with a configurable rotary encoder and OLED display, built around the RP2354A microcontroller and custom MicroPython firmware. Fully programmable through a web-based configurator.

    50 parts2MIT
  • 4 layers46 × 110 mmAware01 h7 rev2 0, the printed circuit board in 3D

    Aware01 h7 rev2 0

    95lux/aware01

    Aarebot is a dynamic realtime sampler built as a Eurorack module. At its core is a stereo tape-style engine with a hot-swapping record/playback buffer - this enables to record and play simultaneously.

    158 parts15GPL-3.0
  • 4 layers78 × 58 mmJohnson node, the printed circuit board in 3D

    Johnson node

    ManchesterStingerMotorsports/johnson-node

    Fully modular CAN node hardware and firmware libraries

    108 parts2
  • 2 layers118 × 78 mmIC PDM V2.0, the printed circuit board in 3D

    IC PDM V2.0

    ManchesterStingerMotorsports/IC-PDM

    IC car PDM for the 2025-2026 Season

    49 parts

Questions

How big is the SolderingStationPCB PCB?

It measures 74.2 × 29.2 mm and has 11 copper layers, 1.6 mm thick.

What parts does the SolderingStationPCB use?

68 parts, built around the LMR50410Y5FQDBVRQ1, B140-E3, B2B-XH-A and BC817-40. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the SolderingStationPCB KiCad files?

From the clytle374/Open-T12-Soldering-Station repository on GitHub, at the commit this page was made from: the board is solderingStationPCB.kicad_pcb and its schematic solderingStationPCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the SolderingStationPCB design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).