

MP Tracker
Open hard- and software solar maximum power point tracker
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 70
- Nets
- 39
- Pads
- 192
- Tracks, vias
- 756, 24
- Pours
- 9
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 27 Feb 2017
- Updated
- 10 Oct 2017
Overview
MP Tracker is an open-source printed circuit board by elektra42, from the elektra42/freifunk-open-mppt repository on GitHub. It is a 2-layer board with 70 parts on 39 nets, routed with 756 tracks and 24 vias.
It is built around the ATMEGA8A-AU, MC34063 and TL081, with the BC817-40 among its other parts. Its parts include 26 resistors, 18 capacitors, 6 diodes, 4 ICs and 4 transistors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
4ATMEGA8A-AU
TQFP-32(7x7)-40℃~+85℃ 10bit 16MHz 1KB 2.7V~5.5V 23 512Byte 8 Bit 8KB AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)MC34063
SOP-80℃~+70℃@(TA) 1 33kHz 3V~40V Adjustable Buck、Boost Built-in Inverting No SOP-8 DC-DC Converters ROHSHXY MOSFETDC-DC ConvertersTL081
SOP-8-18V~18V -20℃~+85℃ 1 1.8mA 100pA 200nA 20V/us 3MHz 3mV 85dB Built-in compensation SOP-8 Operational Amplifier ROHSGcoreOperational AmplifierBC817-40
SOT-23-65℃~+150℃ 1 NPN 100MHz 100nA 250 345mW 45V 500mA 5V 700mV NPN SOT-23 Bipolar (BJT) ROHSNexperiaBipolar (BJT)
README
README.mdThese are preliminary sources and CAD files from the Freifunk-Open-MPP-Tracker project.
SOME LICENSE-FOO:
This is a Open-Source and Open-Hardware project under General Public License v2 and Creative Commons - Attribution - ShareAlike 3.0. For more information, check out the LICENSE file.
A QUICK OVERVIEW OF THE DIRECTORIES:
AVR-FUSES
Contains a XML configuration file to program the fuses of the AVR. I am using the AVR dragon board and AVR-Burn-O-Mat software to program the fuses.
SCHEMATIC AND BOARD
Electronic CAD files and component libraries, made with KiCAD. KiCAD is a free and open ECAD tool. Due to the intend to provide a open hardware and open software project for DIY home-brewers, I have decided to use a free and open source ECAD software tool, too. It is my first project with KiCAD, though.
uC-SOURCECODE
AVR-GCC source and Makefile.
SOME NOTES ABOUT THIS DESIGN
Basically this hardware has two building blocks: The MPP controller section and the buck converter.
At the moment, the buck converter section is based on the el cheapo and low-fi MC33063 controller chip. It can easily be replaced by a faster and more fancy switch converter IC to construct a more powerful and slightly more efficient buck converter section. However, with the external powerful P-MOS switches, the efficiency was already around 94% with the first prototype (measured at 2 Ampere output current).
One reason to replace the MC33063 might be noise. Under low load, the MC33063 will skip pulses of the PWM, so the switching frequency becomes audible.
External references
Parts
70| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 470n | Capacitors_SMD:C_1206 | C1, C2, C3, C7, C10, C12 |
| 4 | Mounting_Holes:MountingHole_3.2mm_M3_DIN965 | , , , | |
| 4 | 1K | Resistors_SMD:R_0805 | R10, R25, R31, R32 |
| 3 | 10k | Resistors_SMD:R_0805 | R5, R13, R19 |
| 3 | 1N4001 | ELEKTRONIK:D_SOD-323_HandSoldering | D2, D7, D9 |
| 3 | 1k | Resistors_SMD:R_0805 | R1, R4, R7 |
| 3 | 3k3 | Resistors_SMD:R_0805 | R9, R12, R27 |
| 3 | 470n | Capacitors_SMD:C_1206_HandSoldering | C16, C17, C18 |
| 2 | 100n | Capacitors_SMD:C_1206_HandSoldering | C9, C11 |
| 2 | 15p | Capacitors_SMD:C_0805 | C4, C5 |
| 2 | 22k | Resistors_SMD:R_0805 | R11, R11 |
| 2 | 27k | Resistors_SMD:R_0805 | R8, R20 |
| 2 | 330u | Capacitors_SMD:c_elec_10x10 | C6, C14 |
| 2 | BC817-40 | TO_SOT_Packages_SMD:SOT-23 | Q1, Q3 |
| 2 | IRFR5303 | TO_SOT_Packages_SMD:TO-252-2Lead | Q2, Q4 |
| 1 | ELEKTRONIK:elektra-hexenlogo | ||
| 1 | Choke_SMD:Choke_SMD_12x12mm_h8mm | L2 | |
| 1 | Pin_Headers:Pin_Header_Straight_2x05 | P1 | |
| 1 | ELEKTRONIK:Freifunk-Logo | ||
| 1 | Capacitors_SMD:c_elec_10x10 | C14 | |
| 1 | 1000u | Capacitors_SMD:c_elec_10x10 | C13 |
| 1 | 10u | Choke_SMD:Choke_SMD_12x12mm_h8mm | L2 |
| 1 | 15k | Resistors_SMD:R_0805 | R26 |
| 1 | 15k | Resistors_SMD:R_1206 | R15 |
| 1 | 1N4148 | Diodes_SMD:SOD-123 | D1 |
| 1 | 27u | Choke_SMD:Choke_SMD_12x12mm_h8mm | L1 |
| 1 | 2k35 | Resistors_SMD:R_0805 | R21 |
| 1 | 3.6864MHz | Crystals:Crystal_HC49-SD_SMD | X1 |
| 1 | 33k | Resistors_SMD:R_0805 | R14 |
| 1 | 47 | Resistors_SMD:R_0805 | R22 |
| 1 | 470R | Resistors_SMD:R_0805 | R3 |
| 1 | 47R | Resistors_SMD:R_0805 | R6 |
| 1 | 4K7 | Resistors_SMD:R_0805 | R2 |
| 1 | 68p | Capacitors_SMD:C_0805 | C8 |
| 1 | 6V2 | Diodes_SMD:SOD-123 | D4 |
| 1 | 6k8 | Resistors_SMD:R_0805 | R16 |
| 1 | ATMEGA8 | Housings_QFP:LQFP-32_7x7mm_Pitch0.8mm | U3 |
| 1 | DIODESCH | ELEKTRONIK:DO-214AB | D5 |
| 1 | MC34063 | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | U1 |
| 1 | MC78L033 | Power_Integrations:SO-8 | U4 |
| 1 | TEMP_SENS | Pin_Headers:Pin_Header_Straight_1x02 | P2 |
| 1 | TL081 | Housings_SOIC:SOIC-8-1EP_3.9x4.9mm_Pitch1.27mm | U2 |
Similar boards
- 2 layers96.3 × 93.6 mm

- 2 layers100 × 100 mm

- 2 layers99.1 × 40 mm

- 2 layers96.3 × 98 mm

Aquarium
baranovskiykonstantin/aquarium
Control the lighting and the heating of the aquarium.
73 parts11 - 2 layers58.4 × 47 mm

AVRUSBLPT
a-sakharov/LptToUsbAdapter
Solution for connecting old LPT device to modern PC via USB
17 parts6MIT - 2 layers87 × 62 mm

- 2 layers23.6 × 20 mm

XenoGCFlex
HDR/XenoGC-Flex
Flashing is done over isp, a raspberry pi can be used for this, see https://github.com/HDR/RaspberryPiISP
21 parts4 - 2 layers302 × 135 mm

Questions
What parts does the MP Tracker use?
70 parts, built around the ATMEGA8A-AU, MC34063, TL081 and BC817-40. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the MP Tracker KiCad files?
From the elektra42/freifunk-open-mppt repository on GitHub, at the commit this page was made from: the board is Schematic-and-Board/MP-Tracker.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the MP Tracker design in my own project?
Its repository states no licence, so its author keeps all rights: ask elektra42 before reusing the design.