Skip to the content
2 layers212 × 67 mmUi board, the printed circuit board in 3D

A SCPI programmable precision resistor

Size
212 × 67 mm
Copper layers
2
Thickness
1.6 mm
Parts
133
Nets
185
Pads
586
Tracks, vias
1,212, 191
Pours
4
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
18 Aug 2023
Updated
2 Nov 2025

Overview

Ui board is an open-source printed circuit board by sbstnh, from the sbstnh/programmable_precision_resistor repository on GitHub, published under the BSD-3-Clause licence. It is a 2-layer board of 212 × 67 mm with 133 parts on 185 nets, routed with 1,212 tracks and 191 vias.

It is built around the STM32L010C6T6, STP16CP05T and 74HC14, with the LL4148, M2.5 and IRLML6402 among its other parts. Its parts include 32 diodes, 27 resistors, 25 switches, 18 capacitors and 10 ICs. It belongs with the STM32 boards of this library.

Main components

8

README

README.md

Programmable Precision Resistor

A SCPI programmable precision resistor

Programmable Precision Resistor

WARNING: The programmable power resistor presented is mains powered. On the power supply board there will be mains/line voltage. Working with/on such devices can lead to damage, injury or death. Don't do it if you're not qualified or authorized to do so. You use the circuits described at you own risk. You have to make sure that the circuit is safe and adheres to the applicable standards in your location. You might operate the mainboard and ui board more safely with a bench or external power supply.

WARNING: I abandoned the AC/DC converter of the initial design mostly due to EMI issues. I ended up using a EI-core (isolation) transformer, bridge rectifier, capacitor two tiny DC/DC converters. Some of the documentation does not reflect this change.

Background and motivation

In 2021/2022 I designed a DC electronic load that would be more capable, but also much more complex than the usual DIY solutions. However, after building a working breadboard prototype of the analog circuitry with 12 ICs including multiple precision and dual opamps, I thought that it might be better to start with a smaller project that would allow me to gain a lot of experience and write much of the non-application specific code that I could use later on for the digital part. Also, at the time I was looking for a decade resistor box to add to my lab. And this is how I started working on a programmable decade resistor, a pretty specialized tool for niche applications.

Introduction

A programmable resistor is a electronic device whose electrical resistance can be adjusted typically through digital signals. Programmable resistors are available in form of integrated circuits (often referred to as digital potentiometers) as well as stand-alone devices/expansion cards. There are many different applications, each with their own set of requirements e. g.:

programmable gain amplifiers sensor emulation, e. g. for integration tests with hardware-in-the-loop simulators automated testing calibrators prototyping Basic concept The programmable resistor closely follows the main principle of resistor decade boxes: connecting multiple devices (“decades”) in series, with each of the devices having a settable resistance of 0 Ω, 1 ⋅ 10^n Ω, 2 ⋅ 10^n Ω, 9 ⋅ 10^n Ω, where n specifies the decade in question.

Those devices are simple resistor networks complemented by one (multi-throw) or more (single- or multi-throw) switches. While the actual topology and resistor values vary vastly, the switch(es) will always either short out or connect certain resistors or simply tap certain nodes of the resistor network. A simple implementation uses a 10-throw rotary switch to tap the nodes of a series resistor network of nine resistors.

Features

ParameterValue / Description
Rangeshort circuit, 1 Ω … 999.999 kΩ, open circuit
Setpoint resolution1 Ω
Short-term setpoint accuracy estimate<=±0.1% of value + 0.15 Ω (2W and 4W). The estimate is based on measurements for a limited number of calibration and validation resistance setpoints. The measurements were performed with an older Agilent 34401A 6.5 digit multimeter for a single DUT. This is NOT a valid strategy to get reliable/reproducible results in the sense of a specification. It's just a more or less plausible envelope based on measurements I took for my prototype.
Display value resolution6.5 digits, 5.5 digits, 4.5 digits, 3.5 digits, but not better than 1 mΩ
Short-term display accuracy estimate<=±0.01% + 0.025 Ω (2W and 4W). This figure is meant to show how much the displayed resistance value (that is based on a calibration) deviates from the value shown on the DMM, the calibration has been performed with.
Thermal drift (estimate based on design)<<50 ppm/K
Power rating>=0.2W for decade 0 (0..9Ω),
>=0.5W else
Exact value depends on setpoint (display)
Bandwidthunspecified
Calibration modes- Uncalibrated: Switches are activated according to entered setpoint, display shows setpoint
- Two-wire (2W), Four-wire (4W): An internal setpoint is calculated based on the calibration values to reduce the error (effects changes for higher resistance values only)
Operating modesFixed: On trigger no change
Step: On trigger step to trigger setpoint value
Up: On trigger increase setpoint (linearly, 1-2-3-4-5-6-7-8-9, 1-2-5, 1-3)
Down: On trigger increase setpoint (linearly, 1-2-3-4-5-6-7-8-9, 1-2-5, 1-3)
List: See list mode
List modeUp to 100 values with individual dwell times
- Start: on trigger; or immediately after mode selection
- Step:
- Auto: Advance index automatically, solely based on dwell time
- Trigger: Advance index on each trigger event, ignoring the dwell time
- Once: Advance index on each trigger event, only after dwell time elapsed
Switchingfast (default), break-before-make
TriggerSource: Bus, External (Rising, Falling, Either), Immediate, Manual, Timer;
Mode: Continuous, Single
Parameter: Delay, Holdoff, Time (Source: Timer)
InhibitInhibit the input
- Latching: Latch input on/off on inhibit input change
- Live: Switch input on/off according to present inhibit input state
Command and trigger execution10ms loops
User interface- 18 digit alphanumeric display:
- Primary display: Resistance setpoint
- Secondary display: Input state, max. current at setpoint, max. voltage at setpoint, max. power at setpoint, hardware setpoint
- Menu-based
- 6 dual color LEDs
- Rotary encoder with push button
- 23 additional push buttons
User presets0-9; 0 is loaded on power-up
Interface- USB
- Two digital inputs, settable polarity (positive, negative) and function (trigger, inhibit, readout)
Power supplySwitch mode

System design

System block diagram

The block diagram provides an overview of the different circuit groups of each functional block, their internal connections and external interfaces. The Programmable Decade Resistor consists of three main functional blocks:

  1. Power supply (Power Supply Board), an external EMI filter is required.
  2. Programmable decades, control and driver circuits (Mainboard)
  3. User Interface (User Interface Board)

The power supply board uses an off-the-shelve AC/DC converter to provide a +15V rail. The +15V rail powers the relays on the mainboard as well as a DC/DC converter. A single DC/DC converter generates a +3.3V supply for both the mainboard and the UI board, including the LED display. The power rails are earth-referenced. (Nevertheless, the inputs of the Programmable Decade Resistor are floating thanks to the isolation of the relays.)

The mainboard’s main controller contains the business logic to control the relays, read the external inputs and run the USB and user interfaces. The main controller communicates with the User Interface Board over I2C which handles the multiplexing of the alphanumeric LED display, scans the switch matrix, decodes the signals of the rotary encoder and drives the buzzer.

Note that these pictures DO NOT represent the final design of the Programmable Precision Resistor and the power supply circuit in particular. Programmable Precision Resistor Programmable Precision Resistor

Results

After the final calibration the results are in. The first diagram shows the absolute value of the deviation between the setpoint and the value indicated by the Agilent 34401A multimeter. Connecting lines between data points for visual purposes only.

Absolute error

The second diagram shows the absolute value of the deviation between the calculated resistance (estimate based on calibration values) and the value indicated by the Agilent 34401A multimeter. Connecting lines between data points for visual purposes only

Absolute error of indicated value

About this repository

This repository contains the PCB design files used in this project. If you'd like to have a look at the interactive bom files you can do so here:

Further information

More details are available at https://hackaday.io/project/191969-programmable-precision-resistor and on my personal site https://sebastianharnisch.de.

Firmware and License

The firmware was created with STM32CubeIDE and uses code auto-generated by or provided with the IDE, including

  • the HAL library, code related to the USB device and other code
  • FreeRTOS

Further more, this project uses a SCPI parser library that can be found here: https://github.com/j123b567/scpi-parser

Most of the auto-generated code as well as the libraries are not included here. Therefore it is recommended to use STM32CubeIDE to create a project for the target device, with the USB device software and FreeRTOS enabled, add the required SCPI library and adapt the code according to the requirements.

For the code not included in this repository the respective licenses will apply instead of the license specified in this repository.

I DO NOT guarantee that the code provided is free of bugs (see LICENSE file for more details).

Parts

133
QtyValueFootprintReferences
24LL4148Diode_SMD:D_MiniMELFD2, D3, D11, D12, D13, D14, D17, D18, D19, D20, D25, D26, D27, D28, D29, D30 +8
8M2.5MountingHole:MountingHole_2.7mm_M2.5_DIN965_PadH1, H2, H3, H4, H5, H6, H7, H8
715k01_Sebastian:R_0603_1608Metric_BoxR11, R14, R15, R21, R23, R24, R26
7IRLML6402Package_TO_SOT_SMD:SOT-23Q2, Q3, Q4, Q5, Q6, Q7, Q8
7dnp01_Sebastian:R_0603_1608Metric_BoxR2, R4, R6, R7, R8, R10, R12
61u01_Sebastian:C_0603_1608Metric_BoxC10, C11, C12, C15, C16, C17
5100n01_Sebastian:C_0603_1608Metric_BoxC5, C6, C7, C8, C18
510k01_Sebastian:R_0603_1608Metric_BoxR3, R16, R18, R19, R20
51k01_Sebastian:R_0603_1608Metric_BoxR13, R17, R22, R25, R27
5STP16CP05Package_SO:TSSOP-24_4.4x7.8mm_P0.65mmU3, U4, U6, U8, U10
3DYSR00P40110101_Sebastian:DYSR00P401101U2, U5, U9
21n01_Sebastian:C_0603_1608Metric_BoxC13, C14
227p01_Sebastian:C_0603_1608Metric_BoxC1, C3
2SW_DP01_Sebastian:PVA1SW13, SW17
2tbd01_Sebastian:R_0603_1608Metric_BoxR5, R9
1100uCapacitor_Tantalum_SMD:CP_EIA-7343-31_Kemet-D_Pad2.25x2.55mm_HandSolderC2
110n01_Sebastian:C_0603_1608Metric_BoxC9
116MHzCrystal:Crystal_HC49-4H_VerticalY1
11N4148Diode_SMD:D_MiniMELFD1
11k01_Sebastian:R_0805_2012Metric_BoxR1
14.7u01_Sebastian:C_0603_1608Metric_BoxC4
174HC14Package_SO:SO-14_3.9x8.65mm_P1.27mmU7
1BSS138Package_TO_SOT_SMD:SOT-23Q1
1Buzzer01_Sebastian:Buzzer_Ekulit_AL-60P06_D12mm_H9mmBZ1
1Conn_02x03_Odd_EvenConnector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_VerticalJ3
1LED_ENTRYLED_THT:LED_D3.0mm-3D23
1LED_INPUTLED_THT:LED_D3.0mm-3D24
1LED_REMOTELED_THT:LED_D3.0mm-3D15
1LED_RUN_STLED_THT:LED_D3.0mm-3D16
1LED_SINGLELED_THT:LED_D3.0mm-3D22
1OMRB3FS01_Sebastian:OMR_B3FSSW5
1PEC11H-4225F-S0024Rotary_Encoder:RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm_CircularMountingHolesSW25
1PWRLED_THT:LED_D3.0mm-3D10
1PWR3.3VConnector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_VerticalJ1
1STM32L010C6Package_QFP:LQFP-48_7x7mm_P0.5mmU1
1SW_001_Sebastian:PVA1SW9
1SW_101_Sebastian:PVA1SW8
1SW_201_Sebastian:PVA1SW12
1SW_301_Sebastian:PVA1SW16
1SW_401_Sebastian:PVA1SW7
1SW_501_Sebastian:PVA1SW11
1SW_601_Sebastian:PVA1SW15
1SW_701_Sebastian:PVA1SW6
1SW_801_Sebastian:PVA1SW10
1SW_901_Sebastian:PVA1SW14
1SW_BACK_DISP01_Sebastian:PVA1SW21
1SW_CHAN01_Sebastian:PVA1SW1
1SW_ENTER01_Sebastian:PVA1SW20
1SW_INPUT01_Sebastian:PVA1SW22
1SW_LEFT01_Sebastian:PVA1SW18
1SW_MENU01_Sebastian:PVA1SW3
1SW_MODE01_Sebastian:PVA1SW2
1SW_RIGHT01_Sebastian:PVA1SW19
1SW_RUN_STOP01_Sebastian:PVA1SW23
1SW_SHIFT01_Sebastian:PVA1SW4
1SW_SINGLE01_Sebastian:PVA1SW24
1UIConnector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_VerticalJ2
1dnpLED_THT:LED_D3.0mm-3D21

More from sbstnh/programmable_precision_resistor

2
  • 2 layers70 × 159.5 mmPower supply, the printed circuit board in 3D

    Power supply

    sbstnh/programmable_precision_resistor

    A SCPI programmable precision resistor

    49 parts65BSD-3-Clause

Similar boards

  • 2 layers268 × 62 mmSmu front 1, the printed circuit board in 3D

    Smu front 1

    jaromir-sukuba/J-SMU

    DIY source-measure unit

    90 parts244
  • 4 layers120 × 100 mmBsc, the printed circuit board in 3D

    Bsc

    shining-man/bsc_hw

    Hardware battery safety controller (BSC)

    286 parts31MIT
  • 2 layers99.5 × 99.5 mmESP32 master, the printed circuit board in 3D

    ESP32 master

    kwiecinski/BMS-and-offgrid-photovoltaic-management-system

    Project contains BMS for lead-acid batteries and ESP-based board used to pull information from EASUN offgrid inverter, energy meters and sensors.

    155 parts3MIT
  • 2 layers274.3 × 30.5 mmNumitron2, the printed circuit board in 3D

    Numitron2

    74hc595/Numitron-Clock

    An alarm clock using 9-segment numitron displays

    56 parts6BSD-3-Clause
  • 2 layers27 × 21.6 mmUnix wall clock, the printed circuit board in 3D

    Unix wall clock

    dotcypress/unix-wall-clock

    Unless you explicitly state otherwise, any contribution intentionally submitted for inclusion in the work by you, as defined in the Apache-2.0 license, shall be dual licensed as above, without any additional terms or…

    9 parts1Apache-2.0
  • 2 layersClock 7 4x1, the printed circuit board in 3D

    Clock 7 4x1

    serhiyk/avr_projects

    Arduino + DS3231 + 12 x MAX7219

    57 parts1
  • 2 layers86.4 × 76.2 mmDash Left, the printed circuit board in 3D

    Dash Left

    uvmaero/AERO_Boards

    All the Boards We Make

    45 parts1
  • 2 layers54.6 × 44.4 mmOscillatorBoard, the printed circuit board in 3D

    OscillatorBoard

    KubbyDev/MusicBox

    A music box containing homemade self-playing instruments.

    11 parts

Questions

How big is the Ui board PCB?

It measures 212 × 67 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Ui board use?

133 parts, built around the STM32L010C6T6, STP16CP05T, 74HC14 and LL4148. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Ui board KiCad files?

From the sbstnh/programmable_precision_resistor repository on GitHub, at the commit this page was made from: the board is pcb/ui_board/ui_board.kicad_pcb and its schematic mechanical/front_panel/front_panel.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Ui board design in my own project?

Its repository publishes it under the BSD-3-Clause licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).