

Esc v5
My custom ESC project
- Size
- 40 × 25 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 37
- Nets
- 56
- Pads
- 198
- Tracks, vias
- 419, 47
- Pours
- 10
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 4 Jan 2024
- Updated
- 4 Jan 2024
Overview
Esc v5 is an open-source printed circuit board by savob, from the savob/esc repository on GitHub, published under the CERN-OHL-W-2.0 licence. It is a 2-layer board of 40 × 25 mm with 37 parts on 56 nets, routed with 419 tracks and 47 vias.
It is built around the ATTINY1617-MN, IRS2334SPBF and TPN2R903PL,L1Q. Its parts include 9 capacitors, 6 transistors, 5 diodes, 3 connectors and 2 resistors. It belongs with the robots and motor control boards and the AVR (ATmega, ATtiny) boards of this library.
Main components
3ATTINY1617-MN
QFN-24-EP(4x4)-40℃~+105℃ 1.8V~5.5V 10bit 16KB 20MHz 22 256Byte 2KB 8 Bit 8bit AVR Built-in FLASH VQFN-24-EP(4x4) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)IRS2334SPBF
SOIC-20-300mil-40℃~+150℃ 10V~20V 125ns 200mA 300uA 350mA 50ns 530ns 530ns 6 IGBT、MOSFET Interleaved conduction protection、Dead-time control Three Phase SOIC-20-300mil Gate Drivers ROHSInfineon TechnologiesGate DriversTPN2R903PL,L1Q
TSON-8(3.1x3.1)1 N-channel 2.1V 2.3nF 2.9mΩ@10V 26nC@10V 30V 70A TSON-8(3.1x3.1) MOSFETs ROHSToshibaMOSFETs
README
README.mdesc
My custom ESC attempt
Parts
37| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | TPN2R903PL | esc:TPN2R903PLL1Q | Q1, Q2, Q3, Q4, Q5, Q6 |
| 4 | DSS15UTR | Diode_SMD:D_SOD-123F | D1, D2, D3, D4 |
| 4 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | JP1, JP2, JP3, JP4 |
| 3 | 1n | Capacitor_SMD:C_0402_1005Metric | C6, C7, C8 |
| 3 | 1u | Capacitor_SMD:C_0603_1608Metric | C3, C4, C5 |
| 2 | 0u1 | Capacitor_SMD:C_0402_1005Metric | C1, C9 |
| 2 | 20 | Resistor_SMD:R_Array_Convex_4x0603 | RN1, RN2 |
| 2 | 33k | Resistor_SMD:R_Array_Convex_4x0603 | RN3, RN4 |
| 1 | 10k | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 10k | Resistor_SMD:R_Cat16-4 | RN5 |
| 1 | 330 | Resistor_SMD:R_0603_1608Metric | R2 |
| 1 | 4n7 | Capacitor_SMD:C_0402_1005Metric | C2 |
| 1 | ATtiny1617-M | Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm | U2 |
| 1 | I2C | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J1 |
| 1 | IRS2334S | Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm | U1 |
| 1 | SERIAL/PWM | Connector_PinSocket_2.54mm:PinSocket_1x06_P2.54mm_Vertical | J3 |
| 1 | STATUS | LED_SMD:LED_0805_2012Metric | D5 |
| 1 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP5 |
| 1 | UPDI | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Horizontal | J2 |
More from savob/esc
7- 2 layers65 × 35 mm

- 2 layers40 × 25 mm

- 2 layers40 × 25 mm

- 2 layers40 × 25 mm

- 2 layers49 × 34 mm

- 4 layers

- 2 layers12 × 13.5 mm

Similar boards
- 2 layers92.5 × 150.6 mm

- 4 layers79.7 × 139.5 mm

- 2 layers92.5 × 151 mm

- 2 layers85.5 × 54 mm

STTS
EthanKerman/STTS
A behbeh credit card sized synth for your wallet. The keys are a full octave ad you can go up and down 2 more. The noise from a piezo disc which is why theres a hole in the board.
43 parts - 2 layers

- 2 layers19.1 × 24.1 mm

Malenki nano2
MarkR42/malenki-esc
A small electronic speed controller for e.g. tiny fighting robots or other rc models
25 parts7 - 4 layers82 × 61 mm

- 4 layers68 × 40 mm

Questions
How big is the Esc v5 PCB?
It measures 40 × 25 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Esc v5 use?
37 parts, built around the ATTINY1617-MN, IRS2334SPBF and TPN2R903PL,L1Q. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Esc v5 KiCad files?
From the savob/esc repository on GitHub, at the commit this page was made from: the board is hardware/esc_v5/esc_v5.kicad_pcb and its schematic hardware/driver_ic_adapter/driver_ic_adapter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Esc v5 design in my own project?
Its repository publishes it under the CERN-OHL-W-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).