

SandKrux
Placa de desenvolvimento baseada no chip K210, com entradas para touch, câmera e LCD grande, criada especificamente para rodar o firmware Krux.
- Size
- 58.3 × 98.2 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 176
- Nets
- 285
- Pads
- 823
- Tracks, vias
- 2,864, 272
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 7 Feb 2026
- Updated
- 12 Apr 2026
Overview
SandKrux is an open-source printed circuit board by sandman21vs, from the sandman21vs/SandKrux repository on GitHub. It is a 2-layer board of 58.3 × 98.2 mm with 176 parts on 285 nets, routed with 2,864 tracks and 272 vias.
It is built around the CH552T, GD25LQ128EWIGR and TMI7003C, with the MT9700-N, PCIE-67P42H and XC6206-3.3V among its other parts. Its parts include 73 capacitors, 53 resistors, 13 ICs, 6 inductors and 5 switches. It belongs with the RISC-V and 8051 (CH55x, STC, AT89) boards of this library.
Main components
12CH552T
TSSOP-20-40℃~+85℃ 12Mbps 3.3V~5V USB 2.0 USB to UART、USB to SPI TSSOP-20 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB ConvertersGD25LQ128EWIGR
WSON-8-EP(5x6)1.65V~2V 100,000 cycles 120MHz 128Mbit 160ms@(32KB) 20 Years 35uA 500us SPI WSON-8-EP(5x6) NOR FLASH ROHSGigaDevice Semicon BeijingNOR FLASHTMI7003C
QFN-20-EP(3x3)-40℃~+125℃@(TJ) 1.5MHz 2.5V~5.5V 3 Adjustable Buck Buck Built-in Yes QFN-20-EP(3x3) DC-DC Converters ROHSTMIDC-DC ConvertersMT9700-N
SOT-23-5-40℃~+85℃ 1 2.4V~5.5V 2A 80mΩ Active High Load Switch Under-voltage lockout、Overcurrent Protection、Over temperature protection、Short-Circuit Protection、Reverse current blocking SOT-23-5 Power Distribution Switches ROHSXI'AN Aerosemi TechPower Distribution SwitchesPCIE-67P42H
SMD,P=0.5mm,卧贴-40℃~+80℃ 4.2mm 67P Female M.2-M Key Surface Mount, Right Angle SMD,P=0.5mm,卧贴 Hard Disk Connector (SAS/SATA/M.2) ROHSSOFNGEdgeboard ConnectorsXC6206-3.3V
SOT-23-3L-40℃~+125℃@(Tj) 1 250mA 3.3V 3uA 400mV@(200mA) 6V Fixed Over Current Protection Positive SOT-23-3L Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSYONGYUTAIVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTL3330AF130QG
SMD-30℃~+70℃ 1.3N 12V 3.4mm 50,000 cycles 50mA 6.9mm Black Rectangular Button SPST-NO Surface Mount, Right Angle SMD Tactile Switches ROHSE-SwitchTactile SwitchesCBW100505U601T
0402-40℃~+85℃ 1 300mA 600mΩ 600Ω@100MHz ±25% 0402 Ferrite Beads ROHSGuangdong Fenghua Advanced Tech (FH)Ferrite Beads05A20L26P
SMD,P=0.5mm,卧贴FFC, FPC (Flat Flexible) Connector AssembliesHanElectricity1N5819HW-7-F-01
SOD-123Schottky DiodesDiodes IncorporatedFH12-40S-0.5SH(55)
SMD,P=0.5mm,卧贴-40℃~+85℃ 0.3mm 0.5mm 2mm 40P Bottom Contact Gold Hinged Lid Phosphor bronze Surface Mount, Right Angle SMD,P=0.5mm,卧贴 FFC, FPC (Flat Flexible) Connector Assemblies ROHSHirose ElectricFFC, FPC (Flat Flexible) Connector AssembliesFH12-6S-0.5SH(55)
SMD,P=0.5mm,卧贴-40℃~+85℃ 0.3mm 0.5mm 2mm 6P Bottom Contact Gold Hinged Lid Phosphor bronze Surface Mount, Right Angle SMD,P=0.5mm,卧贴 FFC, FPC (Flat Flexible) Connector Assemblies ROHSHirose ElectricFFC, FPC (Flat Flexible) Connector Assemblies
README
README.mdSandKrux
Placa de desenvolvimento baseada no chip K210, com entradas para touch, câmera e LCD grande, criada especificamente para rodar o firmware Krux.
Status do projeto
Em desenvolvimento — não finalizado.
Este repositório está em evolução. Mudanças podem ocorrer sem aviso.
Foto da placa
Coloque a imagem em docs/placa.jpg (ou ajuste o caminho abaixo).

Firmware alvo
Este hardware está sendo desenvolvido para o firmware Krux:
Como colaborar
Contribuições da comunidade são muito bem-vindas.
Abra issues, discuta melhorias e proponha alterações.
Licença
GPLv3.
Nota sobre fabricação e apoio ao Krux
Se no futuro você pretender fabricar e vender este dispositivo, fica o pedido de doar ao menos 1% do valor dos dispositivos para a equipe de desenvolvimento do Krux.
Este é um projeto open-source e, sem o trabalho deles, nada disso existiria.
Agradecimentos
Obrigado à comunidade e à equipe do Krux pelo trabalho que torna este projeto possível.
Parts
176| Qty | Value | Footprint | References |
|---|---|---|---|
| 20 | 10uF | PCM_JLCPCB:C_0402 | C4, C5, C6, C7, C21, C26, C27, C37, C41, C43, C50, C53, C59, C66, C76, C78 +4 |
| 16 | 22uF | PCM_JLCPCB:C_0603 | C12, C13, C14, C18, C19, C20, C25, C47, C48, C49, C52, C55, C56, C57, C58, C77 |
| 15 | 100nF | PCM_JLCPCB:C_0402 | C2, C10, C11, C22, C24, C28, C42, C44, C45, C46, C54, C60, C62, C71, C72 |
| 12 | 100Ω | PCM_JLCPCB:R_0402 | R10, R11, R12, R47, R54, R55, R56, R57, R58, R59, R60, R61 |
| 11 | 100pF | PCM_JLCPCB:C_0402 | C29, C30, C31, C32, C33, C34, C35, C36, C38, C39, C40 |
| 6 | 1.5kΩ | PCM_JLCPCB:R_0402 | R24, R25, R26, R34, R35, R36 |
| 6 | 10kΩ | PCM_JLCPCB:R_0402 | R13, R15, R17, R28, R37, R38 |
| 6 | 5.1kΩ | PCM_JLCPCB:R_0402 | R9, R18, R21, R30, R31, R48 |
| 6 | NC | Resistor_SMD:R_0201_0603Metric | R19, R20, R22, R23, R27, R40 |
| 5 | TL3330AF130QG | easyeda2kicad:SW-SMD_E-SWITCH_TL3330 | SW1, SW2, SW3, SW4, SW5 |
| 4 | TestPoint_Small | TestPoint:TestPoint_Pad_D1.0mm | TP1, TP2, TP3, TP4 |
| 4 | ~ | PCM_JLCPCB:Hole, 3mm | H1, H2, H3, H4 |
| 3 | 0Ω | PCM_JLCPCB:R_0402 | R14, R16, R42 |
| 3 | 150kΩ | PCM_JLCPCB:R_0402 | R2, R3, R45 |
| 3 | 18pF | PCM_JLCPCB:C_0402 | C15, C16, C17 |
| 3 | 1uF | PCM_JLCPCB:C_0603 | C1, C69, C70 |
| 3 | 2.2uH,50mA | PCM_JLCPCB:L_0805 | L3, L4, L8 |
| 3 | CBW100505U601T | easyeda2kicad:L0402 | L1, L2, L6 |
| 3 | SolderJumper_2_Bridged | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | JP3, JP4, JP5 |
| 2 | 1kΩ | PCM_JLCPCB:R_0603 | R32, R33 |
| 2 | 2kΩ | PCM_JLCPCB:R_0402 | R8, R46 |
| 2 | 300kΩ | PCM_JLCPCB:R_0402 | R5, R6 |
| 2 | 6pF | PCM_JLCPCB:C_0402 | C3, C23 |
| 2 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1, JP2 |
| 1 | 05A20L26P | easyeda2kicad:FPC-SMD_05A20L26P | FPC1 |
| 1 | 1.25mm-2P socket | easyeda2kicad:CONN-SMD_1.25T-2P | CN3 |
| 1 | 10uF | PCM_JLCPCB:C_0603 | C79 |
| 1 | 12kΩ | PCM_JLCPCB:R_0402 | R4 |
| 1 | 1MΩ | PCM_JLCPCB:R_0402 | R7 |
| 1 | 1N5819HW-7-F | easyeda2kicad:SOD-123_L2.7-W1.6-LS3.7-RD | D1 |
| 1 | 1nF | PCM_JLCPCB:C_0402 | C51 |
| 1 | 200kΩ | PCM_JLCPCB:R_0402 | R39 |
| 1 | 47kΩ | PCM_JLCPCB:R_0402 | R29 |
| 1 | 680kΩ | PCM_JLCPCB:R_0603 | R1 |
| 1 | APX803-31SAG-7 | easyeda2kicad:SOT-23-3_L2.9-W1.3-P1.90-LS2.4-BR | U11 |
| 1 | AXP173_C3345106 | easyeda2kicad:QFN-32_L5.0-W5.0-P0.50-TL-EP3.5-1 | U10 |
| 1 | CH552T | easyeda2kicad:TSSOP-20_L6.5-W4.4-P0.65-LS6.4-BL | U13 |
| 1 | FH12-40S-0.5SH(55) | easyeda2kicad:FPC-SMD_FH12-40S-0.5SH-55 | FPC3 |
| 1 | FH12-6S-0.5SH(55) | easyeda2kicad:FPC-SMD_FH12-6S-0.5SH-55 | FPC4 |
| 1 | GD25LQ128EWIGR | easyeda2kicad:WSON-8_L6.0-W5.0-P1.27-BL-EP | U5 |
| 1 | HX TF-CARD XG8P H1.5 | easyeda2kicad:TF-SMD_HX-TF-CARD-XG8P-H1.5 | U9 |
| 1 | HYCW412-USBC16-065B | easyeda2kicad:USB-C-SMD_HYCW412-USBC16-065B | USB1 |
| 1 | K210_C913414 | easyeda2kicad:BGA-144_L8.0-W8.0-R12-C12-P0.65-BL | U1 |
| 1 | LOGO | easyeda2kicad:Krux_logo | G*** |
| 1 | LOGO | easyeda2kicad:SandKrux | G*** |
| 1 | MT9700-N | easyeda2kicad:SOT-23-5_L2.9-W1.6-P0.95-LS2.9-BL | U7 |
| 1 | PCIE-67P42H | easyeda2kicad:PCIE-SMD_75P-P0.50_HYC01B-05NGFF-420 | U12 |
| 1 | S8050 | PCM_JLCPCB:Q_SOT-23 | Q1 |
| 1 | SM02B-PASS-TBT(LF)(SN) | easyeda2kicad:CONN-SMD_SM02B-PASS-TBT | CN2 |
| 1 | Sign_OSHW_7.3x6.0mm | OLIMEX_Signs-FP:Sign_OSHW_7.3x6.0mmn | Sign_OSHW_7.3x6.0mm |
| 1 | TAJC227K006RNJ | easyeda2kicad:CAP-SMD_L6.0-W3.2-R-RD | C63 |
| 1 | TMI7003C | easyeda2kicad:QFN-20_L3.0-W3.0-P0.40-BL-EP1.7 | U6 |
| 1 | TR01-P2 | Package_DFN_QFN:QFN-32-1EP_4x4mm_P0.4mm_EP2.65x2.65mm | IC1 |
| 1 | X322526MMB4SI | PCM_JLCPCB:CRYSTAL-SMD_4P-L3.2-W2.5-BL | X1 |
| 1 | XC6206-3.3V | easyeda2kicad:SSOT-3_L2.9-W1.6-P0.95-LS2.8-BR | U3 |
| 1 | XC6206P182MR_C347373 | easyeda2kicad:SOT-23-3_L3.0-W1.7-P0.95-LS2.9-BR | U4 |
| 1 | XC6206P302MR_C347375 | easyeda2kicad:SOT-23-3_L3.0-W1.7-P0.95-LS2.9-BR | U8 |
The 175 most common of 176 parts.
Similar boards
- 2 layers97.8 × 17.8 mm

- 6 layers90 × 90 mm

Debugging Board
CausticLime1/Debugging-Board
The purpose of this project is to develop a budget-friendly electronics debugging station that includes various PCBs (Printed Circuit Boards) that incorporate different functionalities.
166 parts1 - 2 layers

- 2 layers80 × 110 mm

NucDeck Left Controller PCB
dmcke5/NucDeck
The Open Source DIY Handheld Gaming PC!
59 parts561CERN-OHL-S-2.0 - 2 layers7.7 × 47.2 mm

- 2 layers26 × 26 mm

- 4 layers69 × 94 mm

TempMonitorRev3.0
lawrancekiamilev/FourChannelDiodebasedTemperatureMonitor
this project is a pcb and programing project. it is designed to be able to read the temperature of any diode based on its non ideal diode factor.
144 parts - 2 layers27.5 × 23.2 mm

Rollino sensor
tompi/rollino
Low-profile DIY finger trackball: ball floats 1 mm above the table, two PMW3610 sensors, nice!nano/ZMK
14 parts
Questions
How big is the SandKrux PCB?
It measures 58.3 × 98.2 mm and has 2 copper layers, 1.6 mm thick.
What parts does the SandKrux use?
176 parts, built around the CH552T, GD25LQ128EWIGR, TMI7003C and MT9700-N. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the SandKrux KiCad files?
From the sandman21vs/SandKrux repository on GitHub, at the commit this page was made from: the board is SandKrux.kicad_pcb and its schematic SandKrux.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the SandKrux design in my own project?
Its repository states no licence, so its author keeps all rights: ask sandman21vs before reusing the design.