Skip to the content
21

TMI7003C

TMIExtended

-40℃~+125℃@(TJ) 1.5MHz 2.5V~5.5V 3 Adjustable Buck Buck Built-in Yes QFN-20-EP(3x3) DC-DC Converters ROHS

Part id
tmi/TMI7003C
Category
DC DC Converters
Package
QFN-20-EP(3x3)
Pins
21
In stock
5,036 at JLCPCB (C840566)
Used on
6 open-source boards

Overview

The TMI7003C is a DC DC Converter made by TMI in a QFN-20-EP(3x3) package with 21 pins. -40℃~+125℃@(TJ) 1.5MHz 2.5V~5.5V 3 Adjustable Buck Buck Built-in Yes QFN-20-EP(3x3) DC-DC Converters ROHS.

PCBKit's library has its footprint (EasyEDA_Cloud:QFN-20_L3.0-W3.0-P0.40-BL-EP1.7, from EasyEDA), ready for a KiCad board. 5,036 are in stock at JLCPCB (part C840566). 6 open-source boards in 6 repositories on GitHub use it.

Symbol

The library has no symbol for this part yet.

Footprint

21
EasyEDA_Cloud:QFN-20_L3.0-W3.0-P0.40-BL-EP1.7From EasyEDA

From the datasheet

10
Supply, least
2.5 V · VIN1/VIN2/VIN3, recommended operating min · p. 4
Supply, most
5.5 V · VIN1/VIN2/VIN3, recommended operating max · p. 4
Supply, absolute maximum
7 V · VIN1/VIN2/VIN3, absolute max · p. 2
Junction, hottest
150 °C · junction temperature absolute max · p. 2
Takes working
150 µA · typical PWM supply current, VOUT = 90%, no load · p. 5
Takes asleep
100 nA · typical shutdown supply current, VEN = 0 V, VIN = 4.2 V · p. 5
Current limit
1.5 A · minimum peak current limit per channel, VIN = 5 V, VOUT = 90% · p. 5
Feedback reference
600 mV · typical regulated feedback voltage, TA = 25°C, PWM · p. 5
Switches at
1.5 MHz · typical oscillation frequency, VOUT = 100% · p. 5
Junction to air (QFN3X3-20)
75 K/W · junction-to-ambient resistance, JESD51-7 four-layer PCB · p. 4

What it is and has

8
Buck regulators
3 high-efficiency synchronous buck regulators · p. 6
Minimum output voltage
0.6 V · p. 1
Switching frequency
Fixed 1.5 MHz · p. 1
Protection
Input undervoltage and overvoltage protection · p. 1
Protection
Thermal fault protection · p. 1
Soft-start
Internal · p. 1
Protection
Over-current protection and hiccup · p. 1
Compliance
Pb-free and RoHS compliant · p. 2

Around it

6
cap 10μF
between VIN1 and GND; Recommended MLCC input capacitor. · p. 3
cap 10μF
between VIN2 and GND; Recommended MLCC input capacitor. · p. 3
cap 10μF
between VIN3 and GND; Recommended MLCC input capacitor. · p. 3
res around 50kΩ
between VOUT and FB; R1, upper feedback-divider resistor for each adjustable output; choose R2 for the required output voltage. · p. 11
cap 10µF
between VOUT and GND; Per buck output; effective capacitance, ESR 2mΩ or less, X5R/X7R or comparable ceramic; mount close to output/ground terminals. · p. 14
cap larger than 4.7µF
between VIN and GND; Minimum effective input capacitance; ESR 10mΩ or less, X5R/X7R or comparable ceramic; mount close to the corresponding power/ground input terminals. · p. 14

Specifications

33
ParameterConditionsAs printedPage
Input Supply Voltagemin -0.3 · max 7 V2
LX Voltagesmin -0.3 · max 7 V2
EN, FB Voltagemin -0.3 · max 7 V2
LX Voltage (<10ns transient)<10ns transientmin -2.5 · max 7.5 V2
LX Voltage (<5ns transient)<5ns transientmin -3.5 · max 8.5 V2
Peak Current limitmax 1.6 A2
Junction Temperature (Note 2)max 150 °C2
Power Dissipationmax 1.6 W2
Lead Temperature (Soldering,10s)Soldering,10smax 260 °C2
Human Body Model for all pins VESD_HBMJEDEC specification JS-001; rating ±2000 Vmax 2000 V4
Voltage RangeINmin 2.5 · max 5.5 V4
Operating Junction Temperature Range TJmin -40 · max 125 °C4
Junction-to-ambient thermal resistance θJAQFN3X3-20; measured on JESD51-7, 4-layer PCBtyp 75 °C/W4
Input Voltage RangeVIN=5V, TA = 25°C, unless otherwise notedmin 2.5 · max 5.5 V5
OVP ThresholdBuck Regulator 1, 2, 3; VIN=5V, TA = 25°Ctyp 6 V5
UVLO ThresholdBuck Regulator 1, 2, 3; VIN=5V, TA = 25°Ctyp 2.3 V5
Input DC Supply Current (PWM Mode)Buck Regulator 1, 2, 3; VIN=5V, TA = 25°C; VOUT = 90%, ILOAD=0mAtyp 150 · max 300 uA5
Input DC Supply Current (PFM Mode)Buck Regulator 1, 2, 3; VIN=5V, TA = 25°C; VOUT = 105%, ILOAD=0mAtyp 40 · max 75 uA5
Input DC Supply Current (Shutdown Mode)Buck Regulator 1, 2, 3; TA = 25°C; VEN= 0V, VIN=4.2Vtyp 0.1 · max 2 uA5
Regulated Feedback Voltage VFBBuck Regulator 1, 2, 3; VIN=5V; TA= 25°C, PWM operationmin 0.588 · typ 0.6 · max 0.612 V5
Oscillation FrequencyBuck Regulator 1, 2, 3; VIN=5V, TA = 25°C; VOUT=100%typ 1.5 MHz5
Oscillation FrequencyBuck Regulator 1, 2, 3; VIN=5V, TA = 25°C; VOUT=0Vtyp 400 kHz5
On Resistance of PMOSBuck Regulator 1, 2, 3; VIN=5V, TA = 25°C; ILX=100mAtyp 300 mΩ5
On Resistance of NMOSBuck Regulator 1, 2, 3; VIN=5V, TA = 25°C; ILX=-100mAtyp 180 mΩ5
Peak Current LimitBuck Regulator 1, 2, 3; TA = 25°C; VIN= 5V, VOUT=90%min 1.5 A5
EN Input High VoltageBuck Regulator 1, 2, 3; VIN=5V, TA = 25°Cmin 1.5 V5
EN Input Low VoltageBuck Regulator 1, 2, 3; VIN=5V, TA = 25°Cmax 0.4 V5
EN Enable Delay TimeBuck Regulator 1, 2, 3; VIN=5V, TA = 25°Ctyp 250 us5
Soft Start TimeBuck Regulator 1, 2, 3; VIN=5V, TA = 25°C; 10%xVOUT to 90%xVOUTmin 750 · typ 1000 · max 1250 us5
EN Leakage CurrentBuck Regulator 1, 2, 3; VIN=5V, TA = 25°C; magnitudes, printed as ±0.01 and ±1.0typ 0.01 · max 1 uA5
LX Leakage CurrentBuck Regulator 1, 2, 3; TA = 25°C; VEN=0V, VIN=VLX=5V; magnitudes, printed as ±0.01 and ±1.0typ 0.01 · max 1 uA5
Thermal Shutdown Threshold (Note 4)Buck Regulator 1, 2, 3; VIN=5V, TA = 25°C; guaranteed by designtyp 160 °C5
Thermal Shutdown Hysteresis (Note 4)Buck Regulator 1, 2, 3; VIN=5V, TA = 25°C; guaranteed by designtyp 20 °C5

Pins, by the datasheet

21
1 NC
No Connection. · p. 3
2 FB3
CH3 feedback input; connect to output voltage with a resistor divider. · p. 3
3 FB2
CH2 feedback input; connect to output voltage with a resistor divider. · p. 3
4 NC
No Connection. · p. 3
5 NC
No Connection. · p. 3
6 LX2
Internal MOSFET switching output of CH2. · p. 3
7 VIN2
CH2 power input; use a 10uF MLCC capacitor between VIN2 and GND. · p. 3
8 EN2
CH2 on/off control input; do not leave floating. · p. 3
9 EN1
CH1 on/off control input; do not leave floating. · p. 3
10 VIN1
CH1 power input; use a 10uF MLCC capacitor between VIN1 and GND. · p. 3
11 LX1
Internal MOSFET switching output of CH1. · p. 3
12 NC
No Connection. · p. 3
13 NC
No Connection. · p. 3
14 FB1
CH1 feedback input; connect to output voltage with a resistor divider. · p. 3
15 NC
No Connection. · p. 3
16 NC
No connection. · p. 3
17 NC
No Connection. · p. 3
18 EN3
CH3 on/off control input; do not leave floating. · p. 3
19 VIN3
CH3 power input; use a 10uF MLCC capacitor between VIN3 and GND. · p. 3
20 LX3
Internal MOSFET switching output of CH3. · p. 3
21 GND(EP)
Solder exposed pad to a large PCB copper plane connected to GND for appropriate dissipation. · p. 3

Ordering codes, by the datasheet

1
TMI7003C
QFN3X3-20 · 3000 per reel; top mark T7003C / YYXXX · p. 2

Open-source boards using it

6
  • 2 layers58.3 × 98.2 mmSandKrux, the printed circuit board in 3D

    SandKrux

    sandman21vs/SandKrux

    Placa de desenvolvimento baseada no chip K210, com entradas para touch, câmera e LCD grande, criada especificamente para rodar o firmware Krux.

    176 parts21
  • 2 layers100 × 150 mmBadge RP2350 FPGA, the printed circuit board in 3D

    Badge RP2350 FPGA

    semitov/riscv-fpga-badge-2026

    Electronic badge PCB for RISC-V Summit Europe 2026 in Bologna, Italy.

    105 parts9CERN-OHL-W-2.0
  • 4 layers65 × 56.5 mmTangnano9k kr260-hat, the printed circuit board in 3D

    Tangnano9k kr260-hat

    calperxd/tangnano9k-kr260-hat

    FPGA HAT for the AMD Kria KR260 based on the Tang Nano 9K (Gowin GW1NR-9, FT2232H, 16-bit parallel link on J21): KiCad 10 schematic, 4-layer PCB and JLCPCB production files

    181 parts1
  • 4 layers70 × 40 mmGw1nr, the printed circuit board in 3D

    Gw1nr

    c4tsnest/gw1nr-ether

    147 parts
  • 4 layers25.5 × 32 mmLinux soc, the printed circuit board in 3D

    Linux soc

    NEOgHacking/linux_soc

    73 parts
  • 2 layers25.5 × 32 mmLinux soc, the printed circuit board in 3D

    Linux soc

    hackclub/hackxpansion

    A modular game console based on RP2354

    57 parts5GPL-3.0

Parts like it

4

Questions

Is there a KiCad symbol and footprint for the TMI7003C?

Yes. the footprint EasyEDA_Cloud:QFN-20_L3.0-W3.0-P0.40-BL-EP1.7, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TMI7003C?

QFN-20-EP(3x3), with 21 pins. Its footprint is drawn on this page.

Where is the TMI7003C datasheet?

TMI publishes it: the Datasheet link on this page opens it.

Where can I order the TMI7003C?

JLCPCB lists it as part C840566, with 5,036 in stock; the sellers' links on this page open their listings.

What can replace the TMI7003C?

Parts like it in the library: the LGS51215 by Legend-Si, the TMI7003 by TMI, the LP6255QVF by LOWPOWER and the TPS51225CRUKR by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TMI7003C?

6 boards in 6 repositories on GitHub; the most starred are listed on this page, with their KiCad files.