

Flight controller pcb
A custom flight controller PCB designed in KiCad 10 using the STM32F405 microcontroller.
- Size
- 44 × 48 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 43
- Nets
- 74
- Pads
- 190
- Tracks, vias
- 294, 33
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 13 Sep 2026
- Updated
- 13 Sep 2026
Overview
Flight controller pcb is an open-source printed circuit board by sanchitagarwal1011, from the sanchitagarwal1011/STM32F405-Flight-controller-PCB repository on GitHub. It is a 2-layer board of 44 × 48 mm with 43 parts on 74 nets, routed with 294 tracks and 33 vias.
It is built around the BMP280, AMS1117-3.3 and ICM-20602. Its parts include 22 capacitors, 6 connectors, 4 resistors, 4 ICs and 1 switch. It belongs with the robots and motor control boards and the STM32 boards of this library.
Main components
3BMP280
LGA-8(2x2.5)-40℃~+85℃ 0.12hpa 1.5pa/K 1.71V~3.6V 1hpa 300nA 30Kpa~1.1bar I2C、SPI Integrated ADC and digital interface、On-chip calibration and non-volatile storage、Standby mode、On-chip temperature output LGA-8(2x2.5) Pressure Sensors ROHSBoschPressure SensorsAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsICM-20602
LGA-16(3x3)-40℃~+85℃ 1.71V~3.45V 16bit 1KB 6uA IMU (accelerometer + gyroscope) SPI、I2C X,Y,Z X,Y,Z ±16g ±2000dps 运动事件检测 LGA-16(3x3) Accelerometers ROHSTDK InvenSenseAccelerometers
README
README.mdSTM32F405 Flight Controller PCB
A custom flight controller PCB designed in KiCad 10 using the STM32F405 microcontroller.
This project focuses on embedded systems, PCB design, and drone electronics.
Project Overview
The board includes:
- STM32F405 microcontroller
- ICM-20602 6-axis IMU
- BMP280 barometric pressure sensor
- AMS1117-3.3 voltage regulator
- USB interface
- ESC signal connections
- RC receiver connections
- Reset and boot controls
- Power filtering and decoupling capacitors
Tools Used
- KiCad 10
- Embedded C
- Git
- GitHub
PCB Design
Schematic
PCB Layout
3D View
Design Features
- STM32F405-based flight controller
- Dedicated ground plane
- Separate power and signal routing
- Decoupling capacitors near IC power pins
- IMU placed close to the microcontroller
- Power filtering for sensitive components
- Design-rule checking using KiCad
Project Status
- Schematic design
- Component selection
- Footprint assignment
- PCB placement
- PCB routing
- Ground-zone filling
- Design-rule checking
- Gerber generation
- PCB manufacturing
- Hardware testing
Reference
This project is inspired by PCB design learning material from Phil’s Lab.
Disclaimer
This is a learning and development project. The board has not yet been flight-tested and should not be used in a real drone.
Author
Sanchit Agarwal
Parts
43| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 100n | Capacitor_SMD:C_0603_1608Metric | C1, C2, C3, C4, C5, C9, C22, C23 |
| 4 | Conn_01x03_Pin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J3, J4, J5, J6 |
| 4 | MountingHole | MountingHole:MountingHole_2.1mm | H1, H2, H3, H4 |
| 3 | 0.1u | Capacitor_SMD:C_0603_1608Metric | C11, C19, C21 |
| 2 | 1.5k | Resistor_SMD:R_0805_2012Metric | R2, R3 |
| 2 | 10p | Capacitor_SMD:C_0603_1608Metric | C12, C13 |
| 2 | 1u | Capacitor_SMD:C_0603_1608Metric | C10, C24 |
| 2 | 2.2u | Capacitor_SMD:C_0805_2012Metric | C7, C8 |
| 2 | 22u | Capacitor_SMD:C_0805_2012Metric | C14, C15 |
| 1 | 10K | Resistor_SMD:R_0805_2012Metric | R1 |
| 1 | 10n | Capacitor_SMD:C_0603_1608Metric | C20 |
| 1 | 120R | Inductor_SMD:L_0603_1608Metric | FB1 |
| 1 | 16Mhz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 1k5 | Resistor_SMD:R_0402_1005Metric | R4 |
| 1 | 2.2u | Capacitor_SMD:C_0603_1608Metric | C18 |
| 1 | 4.7u | Capacitor_SMD:C_0603_1608Metric | C6 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | BMP280 | Package_LGA:Bosch_LGA-8_2x2.5mm_P0.65mm_ClockwisePinNumbering | U5 |
| 1 | Conn_01x04_Pin | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | ICM-20602 | Package_LGA:LGA-16_3x3mm_P0.5mm_LayoutBorder3x5y | U4 |
| 1 | STM32F405RGTx | Package_QFP:LQFP-64_10x10mm_P0.5mm | U1 |
| 1 | SW_SPDT | Button_Switch_SMD:SW_SPDT_PCM12 | SW1 |
| 1 | USB3_B_Micro | Connector_USB:USB_Micro-B_Wuerth_629105150521 | J7 |
Similar boards
- 4 layers64.6 × 57.3 mm

- 2 layers70 × 70 mm

Lab3
obrevskaya/quadcopter_flight_controller_pcb
Проект посвящён разработке печатной платы контроллера полёта квадрокоптера в системе автоматизированного проектирования KiCad.
69 parts - 2 layers50 × 50 mm

- 8 layers30.4 × 25.2 mm

- 8 layers31.3 × 26 mm

UltimateFC v2
crteensy/yolo-fc_1-3S
1-3S capable variant of the Yolo flight controller
192 parts4CC-BY-SA-4.0 - 4 layers36 × 36 mm

Rl fc f405.routed
GabuGravin41/rlpcb
RL PCB sits beside KiCad and works like a senior hardware engineer looking over your shoulder. You describe what you want to build; it helps you choose real parts from your KiCad libraries, works out the values, places…
65 parts2 - 4 layers52.9 × 79.1 mm

RealFCV1
bapsenpai-blip/STM32F405-4-layer-flight-controller
My first PCB revision, not fabricated yet, looking for design review
94 parts1 - 4 layers30.8 × 46.9 mm

Questions
How big is the Flight controller pcb PCB?
It measures 44 × 48 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Flight controller pcb use?
43 parts, built around the BMP280, AMS1117-3.3 and ICM-20602. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Flight controller pcb KiCad files?
From the sanchitagarwal1011/STM32F405-Flight-controller-PCB repository on GitHub, at the commit this page was made from: the board is KiCad/flight_controller_pcb.kicad_pcb and its schematic KiCad/flight_controller_pcb.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Flight controller pcb design in my own project?
Its repository states no licence, so its author keeps all rights: ask sanchitagarwal1011 before reusing the design.