

POS card
my PCBS
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 74
- Nets
- 72
- Pads
- 266
- Tracks, vias
- 0, 0
- Routed
- Not yet
- KiCad
- KiCad 6 (file 20211014)
- Created
- 27 Jan 2022
- Updated
- 24 Aug 2022
Overview
POS card is an open-source printed circuit board by SamsonChau, from the SamsonChau/PCB repository on GitHub. It is a 2-layer board with 74 parts on 72 nets.
It is built around the RP2040, W25Q128JVSIQ and BSS138, with the ABLS-12.000MHZ-B4-T among its other parts. Its parts include 26 resistors, 23 capacitors, 7 connectors, 6 transistors and 5 ICs. It belongs with the RP2040 boards of this library.
Main components
4RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHBSS138
SOT-23-55℃~+150℃ 1 N-channel 1.1Ω@10V、1.2Ω@4.5V 1.2V 1.7nC@10V 17.5pF 340mA 350mW 50V 6.5pF N-Channel SOT-23 MOSFETs ROHShongjiachengMOSFETsABLS-12.000MHZ-B4-T
HC-49S-SMD-20℃~+70℃ 12MHz 18pF 50Ω ±30ppm ±50ppm HC-49S-SMD Crystals ROHSAbraconCrystals
README
README.mdPCB
my PCBS
Parts
74| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | 10k | Resistor_SMD:R_0402_1005Metric | R1, R5, R6, R7, R8, R9, R10, R12, R13, R14, R15, R16, R17, R20, R24, R26 |
| 9 | 100n | Capacitor_SMD:C_0402_1005Metric | C4, C5, C7, C8, C11, C12, C13, C14, C16 |
| 6 | BSS138 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3, Q4, Q5, Q6 |
| 3 | 100nf | Capacitor_SMD:C_0402_1005Metric | C10, C15, C17 |
| 2 | 100 | Resistor_SMD:R_0402_1005Metric | R22, R25 |
| 2 | 100nF | Capacitor_SMD:C_0402_1005Metric | C3, C21 |
| 2 | 10u | Capacitor_SMD:C_0603_1608Metric | C20, C22 |
| 2 | 1k | Resistor_SMD:R_0402_1005Metric | R19, R21 |
| 2 | 1u | Capacitor_SMD:C_0402_1005Metric | C6, C9 |
| 2 | 22pF | Capacitor_SMD:C_0402_1005Metric | C1, C2 |
| 2 | 27.4 | Resistor_SMD:R_0402_1005Metric | R2, R3 |
| 2 | 27p | Capacitor_SMD:C_0402_1005Metric | C18, C19 |
| 2 | SW_Push | Button_Switch_SMD:SW_Push_1P1T_NO_6x6mm_H9.5mm | SW1, SW2 |
| 1 | 100nF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C23 |
| 1 | 10K | Resistor_SMD:R_0402_1005Metric | R23 |
| 1 | 120 | Resistor_SMD:R_0402_1005Metric | R11 |
| 1 | 3.3k | Resistor_SMD:R_0402_1005Metric | R18 |
| 1 | 6k8 | Resistor_SMD:R_0402_1005Metric | R4 |
| 1 | ABLS-12.000MHZ-B4-T | Crystal:Crystal_SMD_HC49-SD | Y2 |
| 1 | ASEAIG-40MHZ-C-S-T | Crystal:Crystal_SMD_TXC_7M-4Pin_3.2x2.5mm | Y1 |
| 1 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J5 |
| 1 | Encoder1 | Connector_JST:JST_PH_B5B-PH-K_1x05_P2.00mm_Vertical | J6 |
| 1 | Encoder2 | Connector_JST:JST_PH_B5B-PH-K_1x05_P2.00mm_Vertical | J7 |
| 1 | MCP2517FD-xSL | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U2 |
| 1 | MCP2562-E-SN | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | NCP1117-3.3_SOT223 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U4 |
| 1 | RP2040 | PolyuRobotics:QFN40P700X700X90-57N | U1 |
| 1 | SWD | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | Term. | TestPoint:TestPoint_Bridge_Pitch2.0mm_Drill0.7mm | JP1 |
| 1 | UART | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-B_Molex-105017-0001 | J4 |
| 1 | User_LED | LED_SMD:LED_0402_1005Metric | D1 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U5 |
| 1 | molex3.0 2x2 | Connector_Molex:Molex_Micro-Fit_3.0_43045-0412_2x02_P3.00mm_Vertical | J1 |
| 1 | power | LED_SMD:LED_0402_1005Metric | D2 |
More from SamsonChau/PCB
12- 2 layers146.1 × 63.5 mm

- 2 layers49 × 59 mm

- 2 layers80.8 × 107.2 mm

- 2 layers181 × 40.6 mm

- 2 layers139.7 × 104.9 mm

- 2 layers85 × 97.4 mm

- 2 layers53.3 × 56.4 mm

- 2 layers141 × 67.6 mm

- 2 layers45.7 × 45.8 mm

- 2 layers61.1 × 53.3 mm

- 2 layers53.3 × 51.8 mm

- 2 layers73.8 × 34 mm

Similar boards
- 2 layers475 × 139.9 mm

Skogaslider main pcb
skogaby/skogaslider
Firmware, CAD, and PCB files for the skogaslider, an RP2040-based controller to simulate Chunithm's gameplay experience
175 parts18MIT - 4 layers82.6 × 82.5 mm

- 4 layers102.9 × 96.7 mm

PicoGUS chipdown
polpo/picogus
Emulation of ISA sound cards and CD-ROM on Raspberry Pi Pico (GUS, SB/Adlib, MPU-401, Tandy, CMS, Panasonic CD-ROM) with USB mouse/joystick support
99 parts805 - 2 layers99.1 × 72.9 mm

- 2 layers30.1 × 65.1 mm

RPi 0 RP2040
Hugoyhu/Pico2040ZeroW
Raspberry Pi Form Factor, RP2040, Wireless support with ESP-01
46 parts7Apache-2.0 - 2 layers210.1 × 98.3 mm

Granola trailmix
michaelswitzer/granola-trailmix
The TrailMix is a low-cost professional grade button box style arcade controller.
48 parts6MIT - 2 layers64 × 48.4 mm

Rp2040-ble
kartik2406/rp2040-ble
A PCB that uses RP2040 MCU and HM-BT4502 BLE passthrough module. This enables the RP2040 to communicated with other devices using Bluetooth. The bluetooth module is connected via UART(0)
42 parts5 - 4 layers188 × 71.8 mm

Combo board
bikeNomad/fluke_884x_continuity_buzzer
Add-in continuity buzzer for the Fluke 8840A and 8842A multimeters using an RP2040 microcontroller
84 parts4MIT
Questions
What parts does the POS card use?
74 parts, built around the RP2040, W25Q128JVSIQ, BSS138 and ABLS-12.000MHZ-B4-T. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the POS card KiCad files?
From the SamsonChau/PCB repository on GitHub, at the commit this page was made from: the board is POS_card/POS_card.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the POS card design in my own project?
Its repository states no licence, so its author keeps all rights: ask SamsonChau before reusing the design.