
CANNONBALL
user-will/PCB_CANNONBALL
An ESP32-C3 dev board with more sensors and features then you could know what to do with

The custom v1 board: a 30 x 52 mm 2-layer PCB integrating the ESP32-C3, motor drivers, USB-C charging, and battery management.
OpenResonance is an open-source printed circuit board by samer-cyber, from the samer-cyber/OpenResonance repository on GitHub. It is a 2-layer board of 30 × 46 mm with 25 parts on 32 nets, routed with 153 tracks and 22 vias.
It is built around the ESP32-C3-WROOM-02-H4 and AP2112K-3.3. Its parts include 7 resistors, 5 connectors, 4 capacitors, 3 ICs and 3 diodes. It belongs with the ESP32 and RISC-V boards of this library.
The custom v1 board: a 30 x 52 mm 2-layer PCB integrating the ESP32-C3, motor drivers, USB-C charging, and battery management.
| File | What it is | You need it to... |
|---|---|---|
OpenResonance.kicad_pro | KiCad 7+ project | open the project in KiCad |
OpenResonance.kicad_sch | Schematic | study or modify the circuit |
schematic.pdf | Schematic as PDF | read the circuit without installing KiCad |
OpenResonance.kicad_pcb | Board layout | modify the PCB |
GERBER-OpenResonance.zip | Fabrication files | order bare boards anywhere |
BOM-OpenResonance.csv | Bill of materials | order assembled boards (JLCPCB parts) |
CPL-OpenResonance.csv | Pick-and-place (component placement) | order assembled boards |
GERBER-OpenResonance.zip.BOM-OpenResonance.csv and CPL-OpenResonance.csv, and check the part
placement preview carefully, every part should sit aligned on its pads,
before you order. Every part in the BOM is referenced by its LCSC part
number, so the assembly quote resolves automatically.BOM-OpenResonance.csv is a plain CSV with one line per part type:
| Column | Meaning |
|---|---|
Comment | What the part is, e.g. 10uF, ESP32-C3-WROOM-02 |
Designator | Which reference(s) it is on the board, e.g. R1, C1,C2,C3 |
Footprint | The land pattern it solders to, e.g. R_0603_1608Metric |
LCSC | LCSC part number: paste it into JLCPCB or lcsc.com to get the exact part |
Quantity | How many of that part go on one board |
Open it in any spreadsheet program, or read it as text. For the full circuit,
see schematic.pdf or open the KiCad project.
V_bat / 2 through 100k/100k, putting a full
4.2 V cell at 2.1 V, inside the ADC's calibrated range. The divider draws only
about 21 microamps.Each motor and the battery land on a JST-PH 2.0 mm footprint. You can fit the connectors and use plugs, or solder the wires straight to the board; see the assembly steps in the main README. On every footprint the inner pair of pads carries the signal and the outer two are ground. The battery footprint is J2 and its polarity is marked on the silkscreen.
This hardware design is licensed under CERN-OHL-W v2. See
LICENSE.md.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | Conn_01x02_Pin | Connector_JST:JST_PH_S2B-PH-SM4-TB_1x02-1MP_P2.00mm_Horizontal | J2, J3, J4, J5 |
| 3 | 10uF | Capacitor_SMD:C_0603_1608Metric | C1, C2, C3 |
| 2 | 100k | Resistor_SMD:R_0603_1608Metric | R1, R6 |
| 2 | 5.1K | Resistor_SMD:R_0603_1608Metric | R2, R5 |
| 2 | D_Schottky | Diode_SMD:D_SOD-123 | D2, D3 |
| 2 | Q_NMOS_GSD | Package_TO_SOT_SMD:SOT-23 | Q1, Q3 |
| 1 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C4 |
| 1 | 10k | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric | R7 |
| 1 | 2K | Resistor_SMD:R_0603_1608Metric | R4 |
| 1 | AP2112K-3.3 | Package_TO_SOT_SMD:SOT-23-5 | U4 |
| 1 | ESP32-C3-WROOM-02 | RF_Module:ESP32-C3-WROOM-02 | U2 |
| 1 | LED_Small | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | MCP73831-2-OT | Package_TO_SOT_SMD:SOT-23-5 | U3 |
| 1 | SW_SPDT | Button_Switch_SMD:SW_SPDT_Shouhan_MSK12C02 | SW1 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |

user-will/PCB_CANNONBALL
An ESP32-C3 dev board with more sensors and features then you could know what to do with


pushtiujeniya/ESP32-C3-WROOM02_dev-board
This project is a custom 2-layer development board designed around the ESP32-C3-WROOM-02 Wi‑Fi + Bluetooth MCU module.



anasskrim61-wq/esp32-c3-mini
Custom ESP32-C3 Mini IoT hardware design and KiCad PCB project

bapsenpai-blip/STM32F405-4-layer-flight-controller
My first PCB revision, not fabricated yet, looking for design review

It measures 30 × 46 mm and has 2 copper layers, 1.6 mm thick.
25 parts, built around the ESP32-C3-WROOM-02-H4 and AP2112K-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the samer-cyber/OpenResonance repository on GitHub, at the commit this page was made from: the board is PCB and Circuit/OpenResonance.kicad_pcb and its schematic PCB and Circuit/OpenResonance.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask samer-cyber before reusing the design.