Skip to the content
2 layers30 × 46 mmOpenResonance, the printed circuit board in 3D

The custom v1 board: a 30 x 52 mm 2-layer PCB integrating the ESP32-C3, motor drivers, USB-C charging, and battery management.

Size
30 × 46 mm
Copper layers
2
Thickness
1.6 mm
Parts
25
Nets
32
Pads
131
Tracks, vias
153, 22
Pours
4
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
28 Feb 2026
Updated
3 Aug 2026

Overview

OpenResonance is an open-source printed circuit board by samer-cyber, from the samer-cyber/OpenResonance repository on GitHub. It is a 2-layer board of 30 × 46 mm with 25 parts on 32 nets, routed with 153 tracks and 22 vias.

It is built around the ESP32-C3-WROOM-02-H4 and AP2112K-3.3. Its parts include 7 resistors, 5 connectors, 4 capacitors, 3 ICs and 3 diodes. It belongs with the ESP32 and RISC-V boards of this library.

Main components

2

README

PCB and Circuit/README.md

PCB & Circuit

The custom v1 board: a 30 x 52 mm 2-layer PCB integrating the ESP32-C3, motor drivers, USB-C charging, and battery management.

Files

FileWhat it isYou need it to...
OpenResonance.kicad_proKiCad 7+ projectopen the project in KiCad
OpenResonance.kicad_schSchematicstudy or modify the circuit
schematic.pdfSchematic as PDFread the circuit without installing KiCad
OpenResonance.kicad_pcbBoard layoutmodify the PCB
GERBER-OpenResonance.zipFabrication filesorder bare boards anywhere
BOM-OpenResonance.csvBill of materialsorder assembled boards (JLCPCB parts)
CPL-OpenResonance.csvPick-and-place (component placement)order assembled boards

Ordering the board (JLCPCB)

  1. Go to jlcpcb.com, choose Order now, and upload GERBER-OpenResonance.zip.
  2. Options the original boards were ordered with: FR-4, 2 layers, 1.0 mm thickness, black solder mask with white silkscreen, HASL finish, tented vias, 1 oz outer copper. The minimum order is five boards; a pair of wristbands needs two, so you will have spares.
  3. Assembled route: enable PCB Assembly, upload BOM-OpenResonance.csv and CPL-OpenResonance.csv, and check the part placement preview carefully, every part should sit aligned on its pads, before you order. Every part in the BOM is referenced by its LCSC part number, so the assembly quote resolves automatically.
  4. Self-solder route: order the bare boards, buy the parts yourself, and reflow or hand-solder them. Every line in the BOM carries an LCSC part number, so you can order the whole set straight from lcsc.com by searching those numbers. The parts are 0603 and SOT-23 sized, so this route needs steady hands and a fine tip.

Reading the bill of materials

BOM-OpenResonance.csv is a plain CSV with one line per part type:

ColumnMeaning
CommentWhat the part is, e.g. 10uF, ESP32-C3-WROOM-02
DesignatorWhich reference(s) it is on the board, e.g. R1, C1,C2,C3
FootprintThe land pattern it solders to, e.g. R_0603_1608Metric
LCSCLCSC part number: paste it into JLCPCB or lcsc.com to get the exact part
QuantityHow many of that part go on one board

Open it in any spreadsheet program, or read it as text. For the full circuit, see schematic.pdf or open the KiCad project.

Design notes

  • Flyback diodes (1N5819HW) across each motor: motors are inductors, so when the MOSFET switches off the collapsing field would otherwise spike the FETs.
  • Bulk decoupling: 10 uF capacitors around the charging path and regulator (C1 to C3) soak up the voltage transients from USB plug-in events and motor load steps that would otherwise stress the charger IC.
  • Battery sense: GPIO 3 reads V_bat / 2 through 100k/100k, putting a full 4.2 V cell at 2.1 V, inside the ADC's calibrated range. The divider draws only about 21 microamps.
  • Trace widths: 0.6 to 0.7 mm for motor/battery power (600 mA+ peaks), 0.5 mm for VBUS, 0.4 to 0.5 mm for 3.3 V logic power, 0.25 mm for signals.
  • Native USB: the C3's built-in USB means no UART bridge chip is needed; the USB-C port both charges and flashes.
  • A boot button connects GPIO 9 to GND for forced download mode.

Connectors

Each motor and the battery land on a JST-PH 2.0 mm footprint. You can fit the connectors and use plugs, or solder the wires straight to the board; see the assembly steps in the main README. On every footprint the inner pair of pads carries the signal and the outer two are ground. The battery footprint is J2 and its polarity is marked on the silkscreen.

License

This hardware design is licensed under CERN-OHL-W v2. See LICENSE.md.

Parts

25
QtyValueFootprintReferences
4Conn_01x02_PinConnector_JST:JST_PH_S2B-PH-SM4-TB_1x02-1MP_P2.00mm_HorizontalJ2, J3, J4, J5
310uFCapacitor_SMD:C_0603_1608MetricC1, C2, C3
2100kResistor_SMD:R_0603_1608MetricR1, R6
25.1KResistor_SMD:R_0603_1608MetricR2, R5
2D_SchottkyDiode_SMD:D_SOD-123D2, D3
2Q_NMOS_GSDPackage_TO_SOT_SMD:SOT-23Q1, Q3
10.1uFCapacitor_SMD:C_0603_1608MetricC4
110kResistor_SMD:R_0603_1608MetricR3
11kResistor_SMD:R_0603_1608MetricR7
12KResistor_SMD:R_0603_1608MetricR4
1AP2112K-3.3Package_TO_SOT_SMD:SOT-23-5U4
1ESP32-C3-WROOM-02RF_Module:ESP32-C3-WROOM-02U2
1LED_SmallLED_SMD:LED_0603_1608MetricD1
1MCP73831-2-OTPackage_TO_SOT_SMD:SOT-23-5U3
1SW_SPDTButton_Switch_SMD:SW_SPDT_Shouhan_MSK12C02SW1
1USB_C_Receptacle_USB2.0_16PConnector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12J1

Similar boards

  • 4 layers25.6 × 23.6 mmCANNONBALL, the printed circuit board in 3D

    CANNONBALL

    user-will/PCB_CANNONBALL

    An ESP32-C3 dev board with more sensors and features then you could know what to do with

    61 parts14
  • 2 layers27.9 × 66.1 mmRemote, the printed circuit board in 3D

    Remote

    EwoudVV/clicker

    wireless 2 switch macropad

    26 parts2
  • 2 layers33.3 × 38 mmESP32-C3-WROOM02 dev board, the printed circuit board in 3D

    ESP32-C3-WROOM02 dev board

    pushtiujeniya/ESP32-C3-WROOM02_dev-board

    This project is a custom 2-layer development board designed around the ESP32-C3-WROOM-02 Wi‑Fi + Bluetooth MCU module.

    30 parts2
  • 4 layers53.5 × 46 mmKindle, the printed circuit board in 3D

    Kindle

    AdityaCoppisetti/Kindle-hackclub

    building my own kindle from scratch

    44 parts1
  • 2 layers52 × 43 mmHologram, the printed circuit board in 3D

    Hologram

    alaotach/eidolon

    23 parts1
  • 4 layers38 × 28.5 mmEsp32 iot pcb, the printed circuit board in 3D

    Esp32 iot pcb

    anasskrim61-wq/esp32-c3-mini

    Custom ESP32-C3 Mini IoT hardware design and KiCad PCB project

    29 parts1
  • 4 layers52.9 × 79.1 mmRealFCV1, the printed circuit board in 3D

    RealFCV1

    bapsenpai-blip/STM32F405-4-layer-flight-controller

    My first PCB revision, not fabricated yet, looking for design review

    94 parts1
  • 4 layers40.4 × 55.5 mmESP32-Dev Kit, the printed circuit board in 3D

    ESP32-Dev Kit

    jishnu085/esp32-c3-custom-board

    Custom ESP32-C3 PCB design using KiCad

    29 parts1

Questions

How big is the OpenResonance PCB?

It measures 30 × 46 mm and has 2 copper layers, 1.6 mm thick.

What parts does the OpenResonance use?

25 parts, built around the ESP32-C3-WROOM-02-H4 and AP2112K-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the OpenResonance KiCad files?

From the samer-cyber/OpenResonance repository on GitHub, at the commit this page was made from: the board is PCB and Circuit/OpenResonance.kicad_pcb and its schematic PCB and Circuit/OpenResonance.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the OpenResonance design in my own project?

Its repository states no licence, so its author keeps all rights: ask samer-cyber before reusing the design.