

Sensortech flex
pcb module using kicad
- Size
- 18 × 40 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 12
- Nets
- 11
- Pads
- 35
- Tracks, vias
- 50, 0
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 18 May 2025
- Updated
- 24 Dec 2025
Overview
Sensortech flex is an open-source printed circuit board by sairudra1, from the sairudra1/flex-sensor-module repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 18 × 40 mm with 12 parts on 11 nets, routed with 50 tracks and 0 vias.
It is built around the MCP602-I/P. Its parts include 5 resistors, 3 connectors, 2 diodes and 1 IC.
Main components
1README
README.md🌟 Flex Sensor Breakout Board
🔧 Why This Design Is Better
❌ Problem with Traditional Flex Sensor Setup
In a conventional setup, a flex sensor must be used with an external resistor to form a voltage divider.
The voltage divider output is then connected to the ADC pin of a microcontroller to measure the bending angle.
⚠️ Limitations of this approach:
-
🔩 Requires an external resistor
→ Leads to messy breadboard wiring -
📉 Voltage divider dependency
→ Causes analog noise and unstable readings -
🎯 ADC conversion issues
→ Reduced accuracy on noisy or low-quality boards -
🧩 Extra external components
→ Not beginner-friendly and increases complexity -
📦 Higher component count
→ Increases BOM and chances of wiring errors
✅ Why This Flex Sensor Breakout Board Is Better
This breakout board integrates the required circuitry directly onto the PCB, eliminating the need for external resistors and simplifying sensor interfacing.
🚀 Key Advantages:
- 🔌 No external resistor required
- 🧹 Clean and compact wiring
- 📊 Stable and noise-reduced output signal
- 🧠 Beginner-friendly plug-and-play design
- 🛠️ Optimized and reduced BOM
📄 Note: The complete Bill of Materials (BOM) is included
this one is 4 layer pcb design
✅ How This Flex Sensor Breakout Board Fixes It This breakout board integrates the necessary circuitry directly on the PCB so you don’t need an external resistor or ADC-based measurement.
You get: 🔌 Direct digital output (D0 pin) 📶 Output becomes HIGH or LOW depending on flex detection 🔄 On-board selector/jumper to choose active-high or active-low output 🚫 No analog signal → no noise issues 🧹 Cleaner wiring → perfect for beginners and compact projects no longer have to build a noisy voltage divider on a breadboard. Just plug in the flex sensor and read a clean digital signal — HIGH when flexed (or LOW, depending on your selection), and ready to be used in any microcontroller project.
Parts
12| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R3 |
| 2 | 200 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4, R5 |
| 2 | Conn_01x03_Pin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2, J3 |
| 2 | LED | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1, D2 |
| 1 | 100k | Potentiometer_THT:Potentiometer_Bourns_3386F_Vertical | RV1 |
| 1 | MCP602 | Package_DIP:DIP-8_W7.62mm | U1 |
| 1 | Screw_Terminal_01x02 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MPT-0,5-2-2.54_1x02_P2.54mm_Horizontal | J1 |
More from sairudra1/flex-sensor-module
1- 2 layers18 × 40 mm

Similar boards
- 2 layers101.8 × 52.5 mm

- 2 layers308.7 × 241.8 mm

OTTOtact
cester-ino/OTTO-hardware
those specs refer to the tactile buttons version, but a led backlight button version is in the works too.
229 parts49GPL-3.0 - 2 layers89.3 × 55 mm

- 4 layers71.1 × 94 mm

Ipotcas
SuperTails/ipotcas
IP over Tin Can and String - Connecting to the internet over two tin cans and a piece of string
75 parts12 - 2 layers187.3 × 109.5 mm

Z80RP2350b
kysilv/z80-rp2350b-zx-compatible
Retrocomputer compatible with ZX Spectrum based on real Z80 + discrete RAM/ROM + rp2350b as ULA
131 parts9GPL-3.0 - 2 layers100 × 100 mm

BLDC STM32 proto 1
g-rahul/Sensored-3-P-BLDC-Closed-Loop-V1
This Firmware was developed as an extension of Ti's Sensored close-loop BLDC motor control using MSP430. Ti's application firmware for MSP430 has been modified for STM32F103 Series MCU's.
131 parts5 - 2 layers245.6 × 85.9 mm

- 4 layers147.8 × 65 mm

Prius gen2
ksmola/PriusG2
Inverter control board for Toyota Prius Gen 2 (XW20) inverter. Some of the schematics are based on Johannes Huebner's work found here. Running openinverter firmware.
149 parts3
Questions
How big is the Sensortech flex PCB?
It measures 18 × 40 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Sensortech flex use?
12 parts, built around the MCP602-I/P. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Sensortech flex KiCad files?
From the sairudra1/flex-sensor-module repository on GitHub, at the commit this page was made from: the board is 4layers/Sensortech_flex/Sensortech_flex.kicad_pcb and its schematic 4layers/Sensortech_flex/Sensortech_flex.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Sensortech flex design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).