

Max2-dac
24-bit Stereo Audio DAC for Raspberry Pi
- Size
- 101.8 × 52.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 158
- Nets
- 123
- Pads
- 435
- Tracks, vias
- 1,390, 91
- Pours
- 9
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 12 Jan 2020
- Updated
- 27 Jan 2020
Overview
Max2-dac is an open-source printed circuit board by dilshan, from the dilshan/max2-audio-dac repository on GitHub, published under the MIT licence. It is a 2-layer board of 101.8 × 52.5 mm with 158 parts on 123 nets, routed with 1,390 tracks and 91 vias.
It is built around the EPM240T100C5, MCP602-I/P and LM1117-3.3, with the SS14 among its other parts. Its parts include 118 resistors, 23 capacitors, 4 connectors, 3 ICs and 2 diodes. It belongs with the audio and music and fPGA and programmable logic boards and the FPGA and CPLD boards of this library.
Main components
4EPM240T100C5
TQFP-100(14x14)0℃~+85℃ 192 2.5V、3.3V 240 240 4.7ns 80 In-system programming MAX II TQFP-100(14x14) Programmable Logic Device (CPLDs/FPGAs)Intel/AlteraProgrammable Logic Device (CPLDs/FPGAs)MCP602-I/P
PDIP-8-40℃~+85℃ 1pA 1pA 2 2.3V/us 2.5uV/℃ 2.7V~6V 2.8MHz 22mA 230uA 29nV/√Hz@1kHz 700uV 90dB Built-in compensation、ESD protection Rail-to-rail output PDIP-8 Operational Amplifier ROHSMicrochip TechnologyOperational AmplifierLM1117-3.3
SOT-2231 1.3V@(1000mA) 15V 1A 2mA 3.3V Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHShongjiachengUncategorisedSS14
SMA(DO-214AC)-55℃~+150℃ 1A 25A 300uA@40V 40V 550mV@1A Independent SMA(DO-214AC) Schottky Diodes ROHSMDDSchottky Diodes
README
README.md24-bit Stereo Audio DAC for Raspberry Pi
This is a 24-bit stereo DAC, which is specifically built for Raspberry Pi boards. This R-2R ladder DAC is developing around Intel / Altera EPM240T100C5N CPLD.
DAC which described in this repo can directly connect with the I2S interface of Raspberry Pi boards. The recommended supply voltage for this DAC is 5V to 8V.
The MCP602 opamp of this module is capable to drive headphone directly. An external AF power amplifier must pair with this module to obtain a higher output power.
This repository contains all the files and binaries to build DAC, which including Intel Quartus Project files, Raspberry Pi Device Tree Overlays, etc.
This is certified open-source hardware project. All the content of this project are distributed under the terms of the following license:
- Hardware License: CC BY 4.0
- Software License: MIT
- Documentation License: CC BY 4.0
Parts
158| Qty | Value | Footprint | References |
|---|---|---|---|
| 50 | 15K | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R11, R13, R15, R17, R19, R21, R23, R25, R27, R29, R31, R101, R103, R105, R107, R108 +34 |
| 48 | 7.5K | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R12, R14, R16, R18, R20, R22, R24, R26, R28, R30, R32, R34, R100, R102, R104, R106 +32 |
| 11 | 0.1MFD | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C7, C10, C11, C12, C13, C14, C15, C16, C17, C18, C19 |
| 4 | 100K | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R110, R111, R114, R115 |
| 4 | 10K | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R6, R7, R8, R9 |
| 4 | 22K | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R1, R2, R3, R4 |
| 3 | MountingHole:MountingHole_3.2mm_M3_ISO14580_Pad | , , | |
| 3 | 0.01MFD | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C3, C5, C8 |
| 3 | 0R | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R5, R117, R118 |
| 2 | 100pF | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C1, C2 |
| 2 | 10K | Potentiometer_THT:Potentiometer_Bourns_3296W_Vertical | RV1, RV2 |
| 2 | 2.2K | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R109, R113 |
| 2 | 4.7MFD | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C4, C6 |
| 2 | 560R | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R112, R116 |
| 1 | 0.1MFD | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C21 |
| 1 | 0.22MFD | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C22 |
| 1 | 100MFD | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C9 |
| 1 | 10MFD | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C23 |
| 1 | 1K | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R10 |
| 1 | 470MFD | Capacitor_THT:CP_Radial_D8.0mm_P5.00mm | C20 |
| 1 | 50.00MHz | Crystal:Crystal_SMD_7050-4Pin_7.0x5.0mm | X1 |
| 1 | AF-OUT | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | DC-IN | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J4 |
| 1 | EPM240T100C5 | Package_QFP:LQFP-100_14x14mm_P0.5mm | U1 |
| 1 | I2S | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical | J1 |
| 1 | JTAG | Connector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_Vertical | J2 |
| 1 | LM1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | MCP602 | Package_SO:SO-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | PWR | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 1 | SS14 | Diode_SMD:D_SMA_Handsoldering | D2 |
The 156 most common of 158 parts.
Similar boards
- 2 layers245.6 × 85.9 mm

- 2 layers248.5 × 36 mm

- 4 layers113.5 × 105.5 mm

Multistepper
eddyem/stm32samples
Code samples and ready projects based on bare-metal STM32
243 parts208 - 2 layers87 × 47 mm

- 2 layers56.9 × 63.9 mm

Opi hat
eddyem/ARMsingleboard
Something for singleboard PC (Orange Pi Zero1/2 etc): I2C, SPI etc.
53 parts2GPL-3.0 - 2 layers107.9 × 76.7 mm

- 2 layers78.5 × 64.5 mm

- 2 layers308.7 × 241.8 mm

OTTOtact
cester-ino/OTTO-hardware
those specs refer to the tactile buttons version, but a led backlight button version is in the works too.
229 parts49GPL-3.0
Questions
How big is the Max2-dac PCB?
It measures 101.8 × 52.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Max2-dac use?
158 parts, built around the EPM240T100C5, MCP602-I/P, LM1117-3.3 and SS14. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Max2-dac KiCad files?
From the dilshan/max2-audio-dac repository on GitHub, at the commit this page was made from: the board is design/max2-dac.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Max2-dac design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
