
PCB1 Single Sensor Validation Rig
Jdowdy05/PointTaken
Point Taken — an optical tactile fingertip based on the TMF8829

Tang Primer 25K + FT601
Rtcl tp25k usb3 is an open-source printed circuit board by ryuz, from the ryuz/rtcl-tp25k-usb3-pcb repository on GitHub. It is a 4-layer board of 80 × 35 mm with 95 parts on 128 nets, routed with 2,189 tracks and 184 vias.
It is built around the FT601Q-B-T, TPS62826DMQR and PCA9306DCUR, with the TPD4E05U06DQAR, USBLC6-2P6 and NTK3134NT1G-ES among its other parts. Its parts include 31 resistors, 30 capacitors, 8 connectors, 5 ICs and 5 transistors.
English version: README_en.md
Sipeed社の Tang Primer 25K に搭載されている GW5A-LV25MG121 には MIPI D-PHY インターフェースが搭載されており、SoM までは配線が来ているようですが、残念ながら標準の Dock base board ではこのラインが未接続のままになっており、利用することができません。
本プロジェクトでは、MIPI D-PHY ラインを活用できるように 0.5mm ピッチ 22pin のコネクタに引き出したうえで、画像データなどを PC と交換できるように FT601 で USB3.0 接続できるオリジナルベース基板の設計データを提供します。

Tang Primer 25K の SoMボード でもともと使われていなかった MIPI ピンを利用するようにしていますが、特に MIPI を活用しなくとも、USB3.0 で FPGA を使えるようにしたボードとも言えますので、今まで FPGA と PC との接続で UART 程度で止まっていた人に本格的な FPGA 活用への第一歩として利用いただければ幸いです。
また、当方では試しておりませんが、GW5A-LV25MG121 の MIPI D-PHY は双方向ですので、MIPI-DSI など、表示系の実験にも利用できる可能性があります。
主な実装内容は以下です。
JTAG は外部に別途ダウンロードケーブルが必要ですが、openFPGAloaderなどを利用する場合は幅広いダウンロードケーブルが利用可能です。
また FT232HL などを利用する場合は、GOWIN EDA の GAO などを使ったデバッグも可能です。
Raspberry PI V2 Camera の接続例と、当方作のRTCL-P3S7-MIPIの接続例です。

Digilent社の JTAG-HS2 の接続例と、秋月電子のFT232HL ハイスピードUSBシリアル変換モジュール の接続例です。

回路図は以下です。
rtcl-tp25k-usb3 ディレクトリ以下に KiCAD 10.0 で設計したデータを格納しています。

JLCPCB の JLC04161H-3313 で製造する想定で設計しています。
下記にて開発中です。
https://github.com/ryuz/rtcl-designs/tree/main/projects/rtcl_tp25k_usb3
当方で製造したものをBOOTH 及び BASE にて販売中です。
詳細は下記をご覧ください。
https://rtc-lab.com/products/rtcl-design-rtcl_tp25k_usb3/
本設計データは、研究開発用の試作実験に供するものであり、利用に際して発生した如何なる損害も作者は補償いたしませんので予めご了承ください。
また設計データについてもなんら品質を保証するものではありません。
本設計データは、クリエイティブ・コモンズ 表示-非営利 4.0 国際 ライセンス(CC BY-NC 4.0)の下で提供されています。
製造した本基板の無断での販売や配布を行わない限りは、趣味や研究開発用途でご自由にお使いいただく事が出来ます。
また、商用に製造販売を希望される場合は、別途ライセンス契約を作者までご相談ください。お問い合わせフォームなどからお問い合わせ頂けます。
渕上 竜司(Ryuji Fuchikami) リアルタイムコンピューティング研究所
| Qty | Value | Footprint | References |
|---|---|---|---|
| 22 | 0.1uF | Capacitor_SMD:C_0402_1005Metric | C1, C2, C10, C11, C12, C15, C16, C17, C18, C19, C20, C21, C22, C23, C24, C25 +6 |
| 14 | 4.7k | Resistor_SMD:R_0402_1005Metric | R2, R3, R68, R69, R72, R74, R76, R77, R78, R79, R80, R81, R82, R83 |
| 5 | 4.7uF | Capacitor_SMD:C_0603_1608Metric | C5, C6, C71, C72, C77 |
| 5 | NTK3134NT1G | rtcl-tp25k-usb3:SOT_34NT1G_ONS | Q2, Q3, Q4, Q5, Q6 |
| 4 | 100 | Resistor_SMD:R_0402_1005Metric | R70, R71, R73, R75 |
| 4 | 150060VS55040 | LED_SMD:LED_0603_1608Metric | LED1, LED2, LED3, LED4 |
| 4 | 2.2k | Resistor_SMD:R_0402_1005Metric | R57, R58, R63, R64 |
| 3 | B3U-1100P | rtcl-tp25k-usb3:B3U-1100P | SW1, SW2, SW4 |
| 2 | 18pF | Capacitor_SMD:C_0402_1005Metric | C3, C4 |
| 2 | <DNP>_R_1608 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R53, R54 |
| 2 | BLM18SG121TN1 | Inductor_SMD:L_0603_1608Metric | FB1, FB2 |
| 2 | DF40C(2.0)-60DS-0.4V(51) | rtcl-tp25k-usb3:CONN_DF40C-60DS_HIR | J3, J4 |
| 1 | 0_1608 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R52 |
| 1 | 1.6k_1% | Resistor_SMD:R_0402_1005Metric | R1 |
| 1 | 100k | Resistor_SMD:R_0402_1005Metric | R67 |
| 1 | 100k_1% | Resistor_SMD:R_0402_1005Metric | R61 |
| 1 | 120pF | Capacitor_SMD:C_0402_1005Metric | C73 |
| 1 | 1M | Resistor_SMD:R_0402_1005Metric | R59 |
| 1 | 200k | Resistor_SMD:R_0402_1005Metric | R62 |
| 1 | 218-2LPSTR | rtcl-tp25k-usb3:218-2LP_CTS | SW3 |
| 1 | 22.6k_1% | Resistor_SMD:R_0402_1005Metric | R60 |
| 1 | ABM8-30.000MHZ-D1X-T | rtcl-tp25k-usb3:XTAL_ABM8-30.000MHz-D1X-T | X1 |
| 1 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J6 |
| 1 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J7 |
| 1 | FT601Q | Package_DFN_QFN:QFN-76-1EP_9x9mm_P0.4mm_EP5.81x6.31mm | U1 |
| 1 | JTAG | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J5 |
| 1 | MIPI_22pin | rtcl-tp25k-usb3:AFC11-S22ICA-00 | J2 |
| 1 | PCA9306DCUR | Package_SO:VSSOP-8_2.3x2mm_P0.5mm | U5 |
| 1 | PMOD | rtcl-tp25k-usb3:PMOD_02x06_2.54mm | J10 |
| 1 | TFM201610ALM-R47MTAA | rtcl-tp25k-usb3:INDC2016X100N | L1 |
| 1 | TPD4E05U06DQA | Package_SON:USON-10_2.5x1.0mm_P0.5mm | U2 |
| 1 | TPS62826DMQR | rtcl-tp25k-usb3:DMQ0006A | U4 |
| 1 | USBLC6-2P6 | Package_TO_SOT_SMD:SOT-666 | U3 |
| 1 | ZX360D-B-10P(30) | rtcl-tp25k-usb3:ZX360DB10P30 | J1 |
The 91 most common of 95 parts.

Jdowdy05/PointTaken
Point Taken — an optical tactile fingertip based on the TMF8829

the78mole/jumpstarter-mono
This is a monorepo containing all jumpstarter tools and (hopefully) adds a standalone server soon.


Batterhead221/brain_board
Custom STM32H753 brain board with USB-C power/input selection, 3.3V buck regulation, microSD, CAN, RS-485, FRAM, flash, debug/programming access, and expansion connectors.


hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

xeno3dev/LumaDD
LumaDD is a Custom Display Driver Board designed around a display I got off Alibaba, with Touch Support. It features HDMI -> MIPI DSI video signal conversion, USB-C for Touch Signals + Power, as well as an onboard…

It measures 80 × 35 mm and has 4 copper layers, 1.6 mm thick.
95 parts, built around the FT601Q-B-T, TPS62826DMQR, PCA9306DCUR and TPD4E05U06DQAR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the ryuz/rtcl-tp25k-usb3-pcb repository on GitHub, at the commit this page was made from: the board is rtcl-tp25k-usb3/rtcl-tp25k-usb3.kicad_pcb and its schematic rtcl-tp25k-usb3/rtcl-tp25k-usb3.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask ryuz before reusing the design.