Skip to the content
2 layers25.4 × 19 mmAccelerometer board, the printed circuit board in 3D

Accelerometer board

ryanhaus/rowan-baja-daq1

Data Acquisition system for Rowan University's Baja SAE 2025-2027 team.

Size
25.4 × 19 mm
Copper layers
2
Thickness
1.6 mm
Parts
17
Nets
20
Pads
63
Tracks, vias
75, 17
Pours
4
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
10 Sep 2025
Updated
3 Nov 2026

Overview

Accelerometer board is an open-source printed circuit board by ryanhaus, from the ryanhaus/rowan-baja-daq repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 25.4 × 19 mm with 17 parts on 20 nets, routed with 75 tracks and 17 vias.

It is built around the BMI323, FXMAR2104UMX and MIC5365-3.3YC5-TR. Its parts include 6 capacitors, 4 resistors, 3 ICs and 2 connectors. It belongs with the sensors and measurement boards of this library.

Main components

3

README

can-module/pcb/README.md

PCB

The CAN Module is a 1" x 0.75" printed circuit board (PCB) designed in KiCad. All KiCad files are available in the 'pcb' directory.

The board features a 48MHz PIC32 microcontroller, a CAN Transceiver, headers for power and CAN communication, as well as 8 GPIO pins.

Below shows an orthographic top and bottom view of the board:

[!NOTE] If more than 8 GPIO pins are required for a particular sensor or module, an I2C GPIO expander can be used, or wires can be soldered to one of the exposed GPIO test points (see here). Alternatively, a larger custom board can be designed, these modules are able to communicate with any CAN-FD compatible device that communicates with a 5V logic level.

Schematic

A schematic of the CAN Module is shown below. Higher-quality pdf available here.

Schematic

Dimensions

The dimensions below may be of use for designing custom enclosures or daughterboards to be mounted to the CAN Module. All dimensions are in mm, and the mounting holes are M2. Additionally, the pin headers have 0.05" (1.27mm) hole spacing. Dimensions of board

Power Requirements

The boards should be powered with +5V DC through the appropriate pins in the vehicle interface.

The total power consumption depends on attached sensors and modules, but 100-200 mA at most will be consumed by the board itself during peak power usage.

[!NOTE] The boards feature reverse polarity protection, a resettable fuse, and ESD protection diodes on all pins within the vehicle interface.

Microcontroller

The microcontroller on the CAN Module is the PIC32CM1216JH01048-I/U5B, an inexpensive and tiny 32-bit ARM microcontroller that operates at 48MHz with 128KB of flash and 16KB of RAM, as well as an embedded hardware CAN controller. See the datasheet here.

CAN Transceiver

The CAN Transceiver on the CAN Module is the ATA6560-GBQW-N. See the datasheet here.

Indication LEDs

There are two indication LEDs present on the CAN Module. One LED is a power indicator LED and is not configurable. The other is configurable and has the cathode connected through a 30k resistor to the PA12 pin on the microcontroller. Each LED has 5V at the anode.

Pins & Connectors

All pins on the CAN Module operate at 5V logic levels by default. There are two distinct sets of pins on the board that serve different purposes, the sensor interface and the vehicle interface, as described and labelled below.

[!WARNING] The headers use 0.05" (1.27mm) hole spacing for space conservation, not the more common 0.1" (2.54mm) spacing.

Sensor Interface

The sensor interface is the set of 8 GPIO and 2 output power pins located on the left side of the board. These pins are intended to provide power to and communicate with some sensor or module, or a custom-designed daughterboard which mounts on top of the CAN Module PCB.

There are two distinct pin headers in the sensor interface, one being 2 pins, and the other being 8 pins. These are the output power and communication headers, respectively.

The output power header has a positive pin (+5V) and a negative pin (GND), which is labelled appropriately on the board.

The communication header has 8 GPIO pins which are directly connected to GPIO pins on the microcontroller. The pins included in this header include GPIO pins PA4 through PA11 from the microcontroller in sequential order, as labelled on the board. These pins were selected because every one of them is capable of acting as a communication interface pin for the SERCOM peripheral on the microcontroller, see the datasheet (Table 4-2) for more info.

[!WARNING] These pins do not have ESD diodes, series resistors, or short circuit protection (other than what is provided by the microcontroller's GPIO pins).

[!NOTE] Some of these pins are powered by AVDD and some are powered by VDDIO. While VDDIO can be changed to 3.3V to use 3.3V logic, AVDD must remain 5V. A future revision of this board could take this into consideration and only expose pins powered by VDDIO, so that 3.3V logic can be achieved without external logic level converters. Another solution could be to power the entire chip by 3.3V and use an ATA6561 instead of the ATA6560, since the former is able to communicate with 3.3V microcontrollers.

Vehicle Interface

The vehicle interface is the set of 2 communication and 2 input power pins located on the right side of the board. These pins are intended to provide power to the CAN Module board and allow for communication between the board and the rest of the vehicle via the shared CAN Bus.

The pins are organized as a single 4-pin header.

Extra GPIOs

13 extra GPIO pins are exposed from the microcontroller and can be used. See the screenshot below to see all labelled test points.

[!NOTE] All GPIO test points are exposed from Port A, so it is not explicitly labelled in the screenshot. For example, the point labelled '13' maps to PA13, '14' to PA14, etc.

[!NOTE] In addition to GPIOs, there is also a test point for +5V. This test point is after all power filtering & fusing, so it may be helpful for debugging power issues.

Programming/Debug Pins

Two serial-wire debug (SWD) pins are exposed and labelled on the back of the board. A SWD-capable interface will be required to program the boards.

[!NOTE] This is TBD, the boards have not been manufactured yet.

Connecting to Other Modules

In order to interface with other devices (i.e., other CAN Modules), they must be wired on the same shared CAN Bus. An example layout is shown below:

CAN Layout Example

Note that every module shares the same four wires that are routed throughout the vehicle. This topology helps significantly reduce the amount of wire required, time spent routing wire, and helps decentralize devices to minimize single points of failure.

Also note that CAN Bus Modules generally do not exist on their own, they will probably need some other attached device or sensor to either provide or process data on the bus.

See here for more info on CAN Bus.

[!WARNING] Make sure that the CAN bus is properly terminated, see here for more info.

Updating This Project

After changes are made to the project, KiBot (must be installed) can be used to automatically create renders of the schematic and PCB used in this documentation.

Navigate to the pcb directory, and run the following:

sh
$ kibot

This command will automatically run the DRC and generate renders. See can-module.kibot.yaml for the configuration.

Parts

17
QtyValueFootprintReferences
4100nCapacitor_SMD:C_0402_1005MetricC1, C2, C7, C8
44k7Resistor_SMD:R_0402_1005MetricR5, R6, R7, R8
21uCapacitor_SMD:C_0402_1005MetricC9, C10
1BMI323BMI323:BMI323_BOSU1
1Conn_01x02Connector_PinSocket_1.27mm:PinSocket_1x02_P1.27mm_VerticalJ2
1Conn_01x08Connector_PinSocket_1.27mm:PinSocket_1x08_P1.27mm_VerticalJ1
1FXMAR2104UMXFXMA2104L8X:ULTRATHIN_MLP_12L_ONSU2
1MIC5365-3.3YC5-TRPackage_TO_SOT_SMD:SOT-353_SC-70-5U6

The 15 most common of 17 parts.

More from ryanhaus/rowan-baja-daq

5
  • 2 layers25.4 × 19 mmCan module, the printed circuit board in 3D

    Can module

    ryanhaus/rowan-baja-daq

    Data Acquisition system for Rowan University's Baja SAE 2025-2027 team.

    49 parts1GPL-3.0
  • 2 layers23.7 × 19.1 mmPmod adapter, the printed circuit board in 3D

    Pmod adapter

    ryanhaus/rowan-baja-daq

    Data Acquisition system for Rowan University's Baja SAE 2025-2027 team.

    19 parts1GPL-3.0
  • 2 layers18 × 9 mmRp2040-zero can adapter, the printed circuit board in 3D

    Rp2040-zero can adapter

    ryanhaus/rowan-baja-daq

    Data Acquisition system for Rowan University's Baja SAE 2025-2027 team.

    13 parts1GPL-3.0
  • 2 layers25.4 × 19.1 mmComm unit, the printed circuit board in 3D

    Comm unit

    ryanhaus/rowan-baja-daq

    Data Acquisition system for Rowan University's Baja SAE 2025-2027 team.

    11 parts1GPL-3.0
  • 2 layers22.9 × 19.1 mmSd card board, the printed circuit board in 3D

    Sd card board

    ryanhaus/rowan-baja-daq

    Data Acquisition system for Rowan University's Baja SAE 2025-2027 team.

    9 parts1GPL-3.0

Similar boards

  • 4 layers111.8 × 80.8 mmPrototype1, the printed circuit board in 3D

    Prototype1

    nmikstas/atari_pokey

    Recreation of the Atari POKEY chip (work in progress)

    164 parts20
  • 10 layers120.4 × 90 mmBmc reference carrier board, the printed circuit board in 3D

    Bmc reference carrier board

    antmicro/dc-scm-osm-l-carrier-card

    DC-SCM Card supporting OSM-L System on Modules

    568 parts13Apache-2.0
  • 4 layers24.4 × 24.4 mmOSO SWAT C1, the printed circuit board in 3D

    OSO SWAT C1

    joeycastillo/Sensor-Watch

    A board replacement for the classic Casio F-91W wristwatch

    40 parts2.1k
  • 4 layers45 × 63.5 mmRedshift, the printed circuit board in 3D

    Redshift

    Dekanova/redshift

    This is the central repository for work on the Redshift PCB.

    77 parts3
  • 2 layers335 × 340.9 mmRCA Radio Telescope, the printed circuit board in 3D

    RCA Radio Telescope

    Glaubinator/Radio-Telescope-RCA

    Radio Telescope System for 1 GHz to 2 GHz Operation

    81 parts3GPL-3.0
  • 4 layers80 × 100 mmIce40 breakout, the printed circuit board in 3D

    Ice40 breakout

    RubenVoell/iceduino

    The basic idea behind this project is to create a simple breakout of an ICE40 FPGA with some LEDs and Buttons to interact with the FPGA and enough resources to run a simple softcore, like a small RISC-V core.

    248 parts3
  • 4 layers70 × 30 mmUsb led controller, the printed circuit board in 3D

    Usb led controller

    kcuzner/usb-led-controller

    This is an LED controller for the lights that came with my In-Win A1 Mini-ITX Tower. It came with a simple 12V RGB LED strip, rather than the now-standard WS2812 addressable LED strips that are so common in today's PCs.

    115 parts2
  • 4 layers115 × 75 mmRF module, the printed circuit board in 3D

    RF module

    putsolardynamics/Telemetry-Module

    146 parts2MIT

Questions

How big is the Accelerometer board PCB?

It measures 25.4 × 19 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Accelerometer board use?

17 parts, built around the BMI323, FXMAR2104UMX and MIC5365-3.3YC5-TR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Accelerometer board KiCad files?

From the ryanhaus/rowan-baja-daq repository on GitHub, at the commit this page was made from: the board is accelerometer-board/pcb/accelerometer-board.kicad_pcb and its schematic accelerometer-board/pcb/accelerometer-board.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Accelerometer board design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).