

Tempo bt
A Bluetooth LE version of the Tempo Skydiving data logger
- Size
- 58.4 × 54 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 69
- Nets
- 106
- Pads
- 358
- Tracks, vias
- 876, 99
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 18 Oct 2025
- Updated
- 27 Sep 2026
Overview
Tempo bt is an open-source printed circuit board by rrainey, from the rrainey/tempo-bt repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 58.4 × 54 mm with 69 parts on 106 nets, routed with 876 tracks and 99 vias.
It is built around the NORA-B106-00B, SAM-M10Q-00B and BMP390, with the MMC5983MA, MX25R6435FZNIL0-TR and MEM2061-01-188-00-A among its other parts. Its parts include 16 resistors, 14 capacitors, 8 ICs, 7 diodes and 5 connectors.
Main components
12NORA-B106-00B
LGA-82加密功能、Mesh组网、硬件TRNG LGA-82 Bluetooth Modules ROHSu-bloxBluetooth ModulesSAM-M10Q-00B
LGA-20Hot start acceleration LGA-20 GNSS Modules ROHSu-bloxGNSS ModulesBMP390
LGA-10(2x2)-40℃~+85℃ 0.6pa/K 1.5uA 1.65V~3.6V 30Kpa~1.25bar 3pa 50pa I2C、SPI Integrated ADC and digital interface、Standby mode、On-chip temperature output Yes LGA-10(2x2) Pressure Sensors ROHSBosch SensortecPressure SensorsMMC5983MA
LGA-16(3x3)-40℃~+105℃ 18bit 2.8V~3.6V 450uA I2C、SPI ±8Gs ±8Gs LGA-16(3x3) 3D Magnetic Sensors ROHSMEMSIC3D Magnetic SensorsMX25R6435FZNIL0-TR
WSON-8(5x6)WSON-8(5x6) NOR FLASH ROHSMXICNOR FLASHMEM2061-01-188-00-A
MICR-SD-CARD1.88mm MicroSD Card (TF Card) Push-Push MICR-SD-CARD SD Card / Memory Card Connector ROHSGlobal Connector Technology (GCT)SD Card / Memory Card ConnectorICM-42688-V
LGA-14(2.5x3)-40℃~+85℃ 1.71V~3.6V 16bit 2KB 7.5uA IMU (accelerometer + gyroscope) Motion event detection SPI、I2C X,Y,Z X,Y,Z ±16g ±2000dps LGA-14(2.5x3) Accelerometers ROHSTDK InvenSenseAccelerometersMCP73831
UncategorisedMicrochip TechnologySPX3819M5-L-3-3/TR
SOT-23-5-40℃~+125℃ 1 16V 3.3V 340mV@(500mA) 40uVrms 500mA 70dB 90uA Fixed Over Current Protection、Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMaxLinearVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsERJ-H3EF1002V
0603-55℃~+175℃ 10kΩ 125mW 75V Thick Film Resistor ±1% ±100ppm/℃ 0603 Chip Resistor - Surface Mount ROHSPanasonicChip Resistor - Surface MountGRM188Z71A106MA73J
06030603 New Arrivals ROHSMurataUncategorisedERJ-H3EF2201V
0603125mW 2.2kΩ Thick Film Resistor ±1% 0603 Chip Resistor - Surface Mount ROHSPanasonicChip Resistor - Surface Mount
README
hardware/tempo-bt/README.mdtempo‑bt V1 board — Peripheral IC Connections
Core MCU/Module: u‑blox NORA‑B106 (nRF5340) OS: Zephyr RTOS Goal: Provide a canonical, test‑ready mapping of logical nets from the NORA‑B106 to each peripheral IC for driver bring‑up and HW connectivity tests.
High‑level digital interconnect
flowchart LR
subgraph Core [NORA‑B106 (nRF5340)]
QSPI[QSPI: SCK, CSN, IO0..IO3]
SPI4[SPI (SPIM4): SCK, MOSI, MISO, CSN]
I2C[I²C: SCL, SDA]
UART_A[UART A: NET_NORA_TX/RX]
UART_B[UART B: APP_NORA_TX/RX, RTS/CTS]
VCOM[USB‑UART: VCOM1_TX/RX]
end
QSPI --> Flash[MX25R6435F 64Mbit QSPI NOR]
SPI4 --> IMU[ICM‑42688‑V 6‑axis IMU]
I2C --> Press[BMP390 Baro]
I2C --> Mag[MMC5983MA Mag]
UART_A --> GNSS[SAM‑M10Q GNSS]
UART_B --> TestApp[App/aux interface]
VCOM --> HostPC[USB‑UART Console]Notes • Net names and bus roles mirror the labels present on the schematic (e.g.,
SPIM4_SCK,QSPI_IO0,SCL,SDA,NET_NORA_TX,APP_NORA_RTS/CTS,VCOM1_RX/TX). • Where interrupts or extra control pins exist but were not explicitly net‑labeled to the MCU on the sheet, they’re called out as TBD/verify so you can tag them to specific GPIOs during bring‑up.
User Outputs / Inputs
| Signal | B106 connection | Description |
|---|---|---|
| LED1 | P1.06 | |
| LED2 | P0.12 | |
| BTN1 | P0.23 | Pushbutton 1 (with hardware debounce) |
| BTN2 | P0.24 | Pushbutton 2 (with hardware debounce) |
Connectivity tables (by peripheral)
1) External QSPI NOR flash — MX25R6435F (64 Mbit)
| Bus | PCB logical net | B106 Port | Flash pin/function | Notes |
|---|---|---|---|---|
| QSPI | QSPI_SCK | P0.17/SCK | SCLK | Primary quad SPI clock |
| QSPI | QSPI_CSN | P0.18/CSN | CS# | Chip select |
| QSPI | QSPI_IO0 | P0.13/IO0 | IO0 (MOSI/SI) | Data/IO0 |
| QSPI | QSPI_IO1 | P0.14/IO1 | IO1 (MISO/SO) | Data/IO1 |
| QSPI | QSPI_IO2 | P0.15/IO2 | IO2 (WP#) | Quad IO2 / Write Protect when legacy |
| QSPI | QSPI_IO3 | P0.16/IO3 | IO3 (HOLD#/RESET#) | Quad IO3 / Hold# when legacy |
Additional compatibility labels seen on sheet:
FLASH_MOSI,FLASH_MISO,FLASH_SCKappear alongside theQSPI_*set; treat as alternative/legacy SPI naming used at fan‑out or test points.
Zephyr tips: Use jedec,spi-nor with qspi child and 4‑line mode; map io0..io3 and cs-gpios to the same nets as above.
2) 6‑axis IMU — ICM‑42688‑V
| Bus | PCB net | B106 Port | IMU pin/function | Notes |
|---|---|---|---|---|
| SPI (SPIM4) | SPIM4_SCK | P0.08/SCK | SCLK | IMU serial clock |
| SPI (SPIM4) | SPIM4_MOSI | P0.09/MOSI | SDI | Master‑out / IMU SDI |
| SPI (SPIM4) | SPIM4_MISO | P0.10/MISO | SDO | Master‑in / IMU SDO |
| SPI (SPIM4) | SPIM4_CSN | P0.11/CSN | CSB | Chip select, active low |
| GPIO | D6 | P1.07 | INT1 | Interrupt to NORA GPIO |
| NC | NC | INT2/FSYNC/CLKIN | Optional secondary INT/FSYNC (unconnected) |
What’s explicit vs. to‑confirm: The SPIM4_* nets are explicit on the sheet and should route to the IMU serial pins. Interrupt lines are present on the symbol but aren’t labeled to a specific net name at the MCU in the text export I parsed—please tag to the intended GPIOs during DTS authoring.
3) Barometric pressure — BMP390
| Bus | PCB net | B106 port | BMP390 pin/function | Notes |
|---|---|---|---|---|
| I²C | SCL | P1.02/TWI | SCL | I²C clock |
| I²C | SDA | P1.03/TWI | SDA | I²C data |
| GPIO | D11 | P1.11 | INT |
4) Magnetometer — MMC5983MA
| Bus | PCB net | B106 port | MMC5983MA pin/function | Notes |
|---|---|---|---|---|
| I²C | SCL | P1.02/TWI | SCL | Shared I²C clock |
| I²C | SDA | P1.03/TWI | SDA | Shared I²C data |
| GPIO | D9 | P1.09 | INT |
5) GNSS module — u‑blox SAM‑M10Q
Note: V1 board has GNSS UART connections only. V2 board will connect PPS TIMEPULSE to a GPIO line (line to-be-determined).
| Interface | NORA‑B106 logical net | SAM‑M10Q function | Notes |
|---|---|---|---|
| UART | NET_NORA_TX → GNSS RX | RXD | Primary GNSS serial in |
| UART | NET_NORA_RX ← GNSS TX | TXD | Primary GNSS serial out |
| UART (alt/app) | APP_NORA_TX/RX, APP_NORA_RTS/CTS | TX/RX/RTS/CTS | A second NORA UART is brought out as “APP_NORA_*”; use if the GNSS is wired to the app port or for auxiliary host/debug depending on stuffing |
| USB‑UART (console) | VCOM1_TX/RX | TX/RX | Labeled console link to host PC/bridge; useful for test logging |
The schematic contains
NET_NORA_TX/RXand alsoAPP_NORA_*plusVCOM1_*. Use the pair that terminates on the SAM‑M10Q in your assembled option. For Zephyr, declare the chosen UART instance asgps0withubx,m10(or use NMEA‑compatible driver) and disable the unused one(s).
Zephyr bring‑up checklist (how to use this map)
-
Pick instances
- QSPI: enable nRF QSPI controller, bind
cs-gpiosandio0..io3toQSPI_*. - SPI: enable
spi4(SPIM4) and bind to IMU. - I²C: enable the I²C controller feeding
SCL/SDAbus; add BMP390 + MMC5983MA as children with proper addresses. - UART: choose either
NET_NORA_*(GNSS) orAPP_NORA_*based on your assembly; reserveVCOM1_*for console.
- QSPI: enable nRF QSPI controller, bind
-
GPIOs/interrupts
- Assign IMU
INT1and the magnetometerINTto listed GPIOs - Add
interrupts = <&gpioX pin IRQ_EDGE_RISING>;in each child node.
- Assign IMU
-
Testing hooks
- Flash: probe with JEDEC ID over QSPI, read SFDP.
- IMU: WHO_AM_I on
SPIM4; read INT on motion. - Baro/Mag: ID registers over I²C; poll data‑ready.
- GNSS: open UART, request UBX‑MON‑VER, check NMEA stream.
- Console: ensure
VCOM1_*maps to the chosen Zephyrconsole.
Appendix — Signal name index (as found on the sheet)
From the schematic net labels (selection):
QSPI_SCK, QSPI_CSN, QSPI_IO0, QSPI_IO1, QSPI_IO2, QSPI_IO3, FLASH_MOSI, FLASH_MISO, FLASH_SCK, SPIM4_SCK, SPIM4_MOSI, SPIM4_MISO, SPIM4_CSN, SCL, SDA, NET_NORA_TX, NET_NORA_RX, APP_NORA_TX, APP_NORA_RX, APP_NORA_RTS, APP_NORA_CTS, VCOM1_TX, VCOM1_RX, SWDIO, SWDCLK, ~RESET, BTN1, BTN2, BTN3, BTN4, D5, D6, D7, D9, D10, D11, D12, D13, P0.31, XL1, XL2, VDDIO, VBACKUP.
D* lines (D5 .. D13) were selected to correspond the the nRF8340 Arduino developement kit board definition.
Parts
69| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 10KOHM-0603-1/10W-1% | peakick:0603 | R11, R13, R14 |
| 3 | 10uF | Capacitor_SMD:C_0603_1608Metric | C2, C4, C8 |
| 3 | 2.2K | Resistor_SMD:R_0603_1608Metric | R5, R9, R10 |
| 3 | STAND-OFFTIGHT | peakick:STAND-OFF-TIGHT | H1, H2, H3 |
| 2 | 100nF | Capacitor_SMD:C_0603_1608Metric | C1, C3 |
| 2 | 2.2KOHM-0603-1/10W-1% | peakick:0603 | R3, R4 |
| 2 | 220OHM-0402 | Resistor_SMD:R_0402_1005Metric | R7, R8 |
| 2 | 4.7UF-0603-6.3V-(10%) | Capacitor_SMD:C_0603_1608Metric | C12, C15 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric | R1, R2 |
| 2 | LTST-S270KGKT | LED_SMD:LED_0603_1608Metric | LED1, LED3 |
| 2 | PTS850 | peakick:PTS850-with-bosses | SW2, SW3 |
| 2 | UBXH07-0000034 | Diode_SMD:D_SOD-923 | D1, D2 |
| 1 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C5 |
| 1 | 1.0UF-0603-16V-10%-X7R | Capacitor_SMD:C_0603_1608Metric | C10 |
| 1 | 100nF | Capacitor_SMD:C_0402_1005Metric | C9 |
| 1 | 10nF | Capacitor_SMD:C_0603_1608Metric | C6 |
| 1 | 1A/23V/620mV | peakick:SOD-323 | D5 |
| 1 | 1K | peakick:0603 | R15 |
| 1 | 2.0k | peakick:0603 | R16 |
| 1 | 2.2UF-0603-10V-20% | Capacitor_SMD:C_0603_1608Metric | C11 |
| 1 | 2.2uF | Capacitor_SMD:C_0603_1608Metric | C7 |
| 1 | 2x5 PTH ARM CORTEX DEBUG | peakick:2X5-PTH-1.27MM-NO_SILK | J5 |
| 1 | 32.768kHz | peakick:CRYSTAL-SMD-3.2X1.5MM | Y1 |
| 1 | 4.7UF-0805-10V-10% | peakick:0805 | C13 |
| 1 | 470KOHM | Resistor_SMD:R_0402_1005Metric | R12 |
| 1 | 499OHM-0402 | Resistor_SMD:R_0402_1005Metric | R6 |
| 1 | 500mA, 6V | Fuse:Fuse_0805_2012Metric | F1 |
| 1 | BMP390 | peakick:LGA10_BMP390_BOS | U1 |
| 1 | CR1220 | peakick:CR1220-2 | B1 |
| 1 | DMP3125L-7 | peakick:SOT23-3@1 | Q1 |
| 1 | FRAME-LETTER | peakick:CREATIVE_COMMONS | FRAME1 |
| 1 | ICM-42688-V | peakick:PQFN50P300X250X97-14N | U4 |
| 1 | IMU_INT1 | TestPoint:TestPoint_THTPad_1.0x1.0mm_Drill0.5mm | TP3 |
| 1 | IO Interfaces | Connector_PinHeader_1.27mm:PinHeader_1x08_P1.27mm_Vertical | J3 |
| 1 | JS102011SAQN | peakick:JS102011SAQN | SW1 |
| 1 | JSTPH | peakick:JSTPH2 | J1 |
| 1 | LTST-C19HE1WT | peakick:LTST-C19HE1WT | RGB1 |
| 1 | LTST-S270KRKT | LED_SMD:LED_0603_1608Metric | LED2 |
| 1 | MCP73831 | peakick:SOT23-5 | U8 |
| 1 | MEM2061-01-188-00-A | peakick:MICROSD | X1 |
| 1 | MMC5983MA | peakick:MMC5983MA_MEM | U3 |
| 1 | MX25R64 | Package_SON:WSON-8-1EP_6x5mm_P1.27mm_EP3.4x4mm | U5 |
| 1 | NET_NORA_RX | TestPoint:TestPoint_Pad_1.0x1.0mm | TP2 |
| 1 | NET_NORA_TX | TestPoint:TestPoint_Pad_1.0x1.0mm | TP1 |
| 1 | NORA-B106-00B | peakick:XCVR_NORA-B106-00B | U7 |
| 1 | OSHW-LOGOS | peakick:OSHW-LOGO-S | LOGO1 |
| 1 | QWIIC_CONNECTORJS-1MM | peakick:JST04_1MM_RA | J4 |
| 1 | RESET | Button_Switch_SMD:SW_Push_1P1T_NO_CK_KMR2 | SW4 |
| 1 | SAM-M10Q | peakick:MODULE_SAM-M8Q-0-10 | U2 |
| 1 | SPX3819M5-L-3-3/TR | peakick:SOT23-5 | U6 |
| 1 | USB_C_Receptacle_USB2.0 | peakick:GCT-USB4105-GF-A modified-USB-C 16P | J2 |
| 1 | VBATT | TestPoint:TestPoint_THTPad_1.0x1.0mm_Drill0.5mm | TP4 |
| 1 | Yellow | peakick:LED-0603 | LED4 |
Similar boards
- 2 layers44.5 × 50.8 mm

- 8 layers90.5 × 49.5 mm

- 4 layers92.5 × 101.6 mm

- 4 layers100 × 70 mm

ZSWatch Watch DevKit
ZSWatch/Watch-DevKit-HW
The hardware repo for the ZSWatch Development Kit.
132 parts188GPL-3.0 - 2 layers40.5 × 49.5 mm

Nora minimal
rain-1/nora-b106
Minimum assembly is still U1 plus C1 (4.7 µF) and C2 (100 nF), with external regulated 3.3 V and SWD wires. Headers are optional. The module's 82 hidden LGA pads need controlled reflow/hot-plate assembly.
18 parts - 8 layers90.2 × 101.1 mm

RevC fm
Sierra-Lobo/mainboard-hardware
PyCubed mainboard v5 fork by Sierra Lobo for Foras Promineo CubeSat
644 parts1 - 4 layers80 × 50 mm

- 4 layers32 × 63.8 mm

Questions
How big is the Tempo bt PCB?
It measures 58.4 × 54 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Tempo bt use?
69 parts, built around the NORA-B106-00B, SAM-M10Q-00B, BMP390 and MMC5983MA. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Tempo bt KiCad files?
From the rrainey/tempo-bt repository on GitHub, at the commit this page was made from: the board is hardware/tempo-bt/tempo-bt.kicad_pcb and its schematic hardware/tempo-bt/tempo-bt.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Tempo bt design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).