
Pdcharger 100W
NerdyProjects/PDbatCharger
A 100W PD3.2 Battery Charger for 4-13S Li battery packs with power bank function

An ESP32-WROOM32E-N4 based remote start module for SRv4 kit.
Remote Start is an open-source printed circuit board by roboticsoutreach, from the roboticsoutreach/remote-start-hw repository on GitHub, published under the CERN-OHL-W-2.0 licence. It is a 2-layer board of 48.3 × 37 mm with 21 parts on 48 nets, routed with 109 tracks and 19 vias.
It is built around the TLV1117-33DCY, 2N7002E and SL1B. Its parts include 5 capacitors, 4 resistors, 4 diodes, 4 connectors and 2 ICs. It belongs with the ESP32 boards of this library.
An ESP32-WROOM32E-N4 based remote start module for SRv4 kit.
This project is licensed under the CERN Open Hardware Licence (Weakly Reciprocal).
TBC
| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 220R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R4 |
| 1 | 100n | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2 |
| 1 | 100u | Capacitor_Tantalum_SMD:CP_EIA-3528-21_Kemet-B_Pad1.50x2.35mm_HandSolder | C5 |
| 1 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1 |
| 1 | 10u | Capacitor_Tantalum_SMD:CP_EIA-3528-21_Kemet-B_Pad1.50x2.35mm_HandSolder | C4 |
| 1 | 1u | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3 |
| 1 | 22u | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1 |
| 1 | 2N7002E | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | 3V3 | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D2 |
| 1 | 470R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2 |
| 1 | 5V | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D1 |
| 1 | ESP32-WROOM-E | PCM_Espressif:ESP32-WROOM-32E | U1 |
| 1 | Ext_Start | Connector_Wuerth_WR-TBL:Wuerth_WR-TBL_691307300002_1x03_P3.81mm | J4 |
| 1 | JTAG | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical | J2 |
| 1 | LOGO | Graphics:Logo_SRO | G*** |
| 1 | PROG | Connector_PinHeader_1.27mm:PinHeader_2x03_P1.27mm_Vertical | J1 |
| 1 | Power_In | Connector_Wuerth_WR-TBL:Wuerth_WR-TBL_691307300002_1x03_P3.81mm | J3 |
| 1 | SL1B | Diode_SMD:D_SOD-123F | D7 |
| 1 | Start | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D3 |
| 1 | TLV1117-33 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |

NerdyProjects/PDbatCharger
A 100W PD3.2 Battery Charger for 4-13S Li battery packs with power bank function

carmisergio/denon-preout-mod
PCB designs and firmware for the Denon AVR-X1300W Pre-out mod

apfaudio/eurorack-pmod
A eurorack-friendly audio frontend compatible with many FPGA boards, based on the AK4619VN audio CODEC.

mon/evoluent_better_pcb
PCBs using better sensor for Evoluent VerticalMouse products

EvanKrall/ipad_touchscreen_driver
A PCB designed to interface with the iPad (A1219) touchscreen

daniestevez/aquarium-controller
Arduino-based Aquarium controller

burnettlab/Indoor-Air-Quality-Monitor
2023 Portland State University Indoor Air Quality Monitor Capstone Project

pez-globo/pufferfish-electronics
Circuit schematics and PCB layouts for the Pufferfish ventilator.
It measures 48.3 × 37 mm and has 2 copper layers, 1.6 mm thick.
21 parts, built around the TLV1117-33DCY, 2N7002E and SL1B. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the roboticsoutreach/remote-start-hw repository on GitHub, at the commit this page was made from: the board is Remote_Start.kicad_pcb and its schematic Microcontroller.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the CERN-OHL-W-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).