Skip to the content
6 layers31.7 × 110 mmEurorack pmod pcb, the printed circuit board in 3D

Eurorack pmod pcb

apfaudio/eurorack-pmod241

A eurorack-friendly audio frontend compatible with many FPGA boards, based on the AK4619VN audio CODEC.

Size
31.7 × 110 mm
Copper layers
6
Thickness
1.6 mm
Parts
155
Nets
147
Pads
637
Tracks, vias
1,920, 331
Pours
5
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
18 Jun 2022
Updated
29 Jan 2026

Overview

Eurorack pmod pcb is an open-source printed circuit board by apfaudio, from the apfaudio/eurorack-pmod repository on GitHub. It is a 6-layer board of 31.7 × 110 mm with 155 parts on 147 nets, routed with 1,920 tracks and 331 vias.

It is built around the LTV-357T, VBUS05L1-DD1 and MMBFJ111, with the 2N7002E among its other parts. Its parts include 42 resistors, 31 capacitors, 26 diodes, 11 ICs and 11 connectors. It belongs with the audio and music and fPGA and programmable logic boards and the FPGA and CPLD boards of this library.

Main components

4

README

README.md

ci workflow

Note: this repository contains Verilog examples for using Eurorack-PMOD with different FPGA boards. If you are trying to pair it with Tiliqua or Amaranth HDL, see the quickstart guide there

Eurorack PMOD

Eurorack PMOD is an open hardware Eurorack module that plugs directly into many FPGA boards, which makes it easy to combine the world of FPGAs and hardware electronic music synthesis.

The hardware looks like this:

image

How does it work? (tutorial video)

:notes: Project Showcase :sparkles:

R3.5 hardware details

Some minor improvements over R3.3, with the following changes:

  • Additional output mute stage: 4 JFETs controlled by the ^MUTE pin (PDN pin was removed and renamed to ^MUTE - semantics are the same as before - HIGH is unmuted).
  • Improved noise performance and DC tracking by adding an additional onboard 3.3V regulator for the analog domain.
  • Touch IC switched from 8-channel to 16-channel version, so that the XRESET pin is not shared with one of the touch jacks.

Note: At this time, this Verilog repo is a bit out of date and refers to R3.3 in a few places, although I am shipping R3.5. I have tested this repository also on R3.5, just make sure to compile with HW_R35. See here for more details.

R3.3 hardware details

labelled eurorack-pmod 3.3

  • 3HP module compatible with modular synthesizer systems.
    • Module depth is 35mm with both ribbon cables attached.
  • PMOD connector compatible with many FPGA development boards.
  • 8 (4 in + 4 out) DC-coupled audio channels, 192KHz / 32bit sampling supported.
  • PWM-controlled, user-programmable red/green LEDs on each output channel.
  • Jack insertion detection on input & output jacks.
  • Calibration EEPROM for unique ID and storing calibration data.
  • [new!] Touch and proximity sensing on all unused jacks as an extra input method.
    • See the gateware/cores/touch_cv.sv core for an example of how to use this.

Included examples

This repository contains a bunch of example DSP cores which are continuously being updated:

  • gateware/cores/pitch_shift.sv - Pitch shifter
  • gateware/cores/filter.sv - Filter (low pass + resonance)
  • gateware/cores/touch_cv.sv - Touch sensing to CV converter
  • gateware/cores/clkdiv.sv - Clock divider
  • gateware/cores/sampler.sv - .wav sampler
  • gateware/cores/seqswitch.sv - Sequential routing switch
  • gateware/cores/digital_echo.sv - Echo / delay effect
  • gateware/cores/vca.sv - VCA (voltage controlled amplifier)
  • gateware/cores/vco.sv - VCO (voltage controlled oscillator)
  • gateware/cores/bitcrush.sv - Bitcrusher

These examples can all run out of the box on the development boards listed below.

Choosing an FPGA development board

An FPGA development board itself is NOT included! Essentially anything iCE40 or ECP5 based that has a PMOD connector will support the open-source tools and the examples in this project. Just make sure you have enough LUTS, >3K is enough to do interesting things.

The following development boards have been tested with eurorack-pmod and are supported by the examples in the github repository

  • iCEbreaker (iCE40 based)
  • iCESugar (iCE40 based, iCE40UP5K version)
  • ECPIX-5 (ECP5 based)
  • Colorlight i5 (ECP5 based)
  • Colorlight i9 (ECP5 based)
  • pico-ice from TinyVision (iCE40 based)
  • CCGM1A1 Gatemate EVB from CologneChip - experimental! see here

PMOD Pinout

assembled eurorack-pmod module R3.3 (bottom)

The PMOD pinout is on the silkscreen on the back side of the board. Details are below. Note that Pin 1 is the SQUARE pad.

  1. SDI (AK4619VN SDIN1)
  2. SCL (I2C SCL for AK4619VN CODEC, EEPROM, LED + JACK IO expanders)
  3. SDO (AK4619VN SDOUT1)
  4. SDA (I2C SDA)
  5. LRCK (CODEC clock line)
  6. PDN (CODEC power down, also connected to LED output enable and JACK reset line -- HIGH means everything is on)
  7. BICK (CODEC clock line)
  8. MCLK (CODEC clock line)
  9. GND
  10. GND
  11. 3V3 IN
  12. 3V3 IN

Getting Started

I have tested builds on Linux, Mac and Windows (under MSYS2). All are tested in CI.

  1. Install the OSS FPGA CAD flow.

    • You may be able to get yosys / verilator from other package managers but I recommend using the releases from YosysHQ so you're using the same binaries that CI is using.
    • On Linux, once the YosysHQ suite is installed and in PATH, you should be able to just use make in the gateware directory.
    • On Windows, CI is using MSYS2 with MINGW64 shell. Install MSYS2, MINGW64, extract the oss-cad-suite from YosysHQ and add it to PATH. Then you should be able to use make in the gateware directory.
    • Note: The gateware is automatically built and tested in CI, so for either platform it may be helpful to look at .github/workflows/main.yml.
  2. Build or obtain eurorack-pmod hardware and connect it to your FPGA development board using a ribbon cable or similar. (Double check that the pin mappings are correct, some ribbon cables will swap them on you! Default pinmaps are for the ribbon cables I shipped with hardware, you need to flip the pinmaps for a direct connection PMOD -> FPGA)

  3. Try some of the examples. From the gateware directory, type make to see valid commands. By default if you do not select a CORE it will compile a bitstream with the 'mirror' core, which just sends inputs to outputs. Note, you'll need to run git submodule update --init --recursive from the repo root after checkout.

  4. Calibrate your hardware using the process described in gateware/cal/cal.py. Use this to create your own gateware/cal/cal_mem.hex to compensate for any DC biases in the ADCs/DACs. (this step is only necessary if you need sub-50mV accuracy on your inputs/outputs, which is the case if you are tuning oscillators, not so much if you are creating rhythm pulses.

Project structure

The project is split into 2 directories, hardware for the PCB/panel and gateware for the FPGA source. Some interesting directories:

  • gateware/cores: example user core implementations (i.e sequential switch, bitcrusher, filter, vco, vca, sampler etc).
  • gateware/top.sv: top-level gateware with defines for selecting features.
  • gateware/cal/cal.py: tool used to calibrate the hardware after assembly, generating calibration memory.
  • gateware/drivers: driver for CODEC and I2C devices used on this board.
  • hardware/eurorack-pmod-r3: KiCAD design files for PCB and front panel.
  • hardware/fab: gerber files and BOM for manufacturing the hardware.

Manufacturing

R3.1 Hardware (no longer manufactured)

The above README focuses on R3.3/R3.5, which is currently being manufactured.

Revision R3.1 was sold out in 2023. It's no longer manufactured, however this repository still supports it if you use the HW_REV=HW_R31 flag when building. I left some of the old photos here in case they are useful.

From the gateware perspective, there is almost no difference between R3.1 and R3.3 and so any cores should be compatible with both (unless they use new features of R3.3 e.g. touch sensitive jacks).

R3.1 boards

assembled eurorack-pmod module R3.0 (panel) assembled eurorack-pmod module R3.0 (top)

R3.1 hardware details

labelled eurorack-pmod 3.0

R3.1 technical

  • 3HP module compatible with modular synthesizer systems.
    • Module depth is 47mm with both ribbon cables attached
    • This fits nicely in e.g. a 4MS POD 48X (pictured below).
  • PMOD connector compatible with most FPGA development boards.
  • 8 (4 in + 4 out) DC-coupled audio channels, 192KHz / 32bit sampling supported.
  • PWM-controlled, user-programmable red/green LEDs on each output channel.
  • Jack insertion detection on input & output jacks.
  • Calibration EEPROM for unique ID and storing calibration data.
  • I/O is about +/- 8V capable, wider is possible with a resistor change.

Known limitations

  • Moved to github issues

Photos

eurorack-pmod R3.1 connected to iCEBreaker

assembled eurorack-pmod module (in system)

License

OSHW logo

Hardware and gateware are released under the CERN Open-Hardware License V2 CERN-OHL-S, mirrored in the LICENSE text in this repository.

If you wish to license parts of this design in a commercial product without a reciprocal open-source license, or you have a ground-breaking idea for a module we could work on together, feel free to contact me directly. See sebholzapfel.com.

Copyright (C) 2022-2024 Sebastian Holzapfel

The above LICENSE and copyright notice does NOT apply to imported artifacts in this repository (i.e datasheets, third-party footprints).

Parts

155
QtyValueFootprintReferences
164K7Resistor_SMD:R_0402_1005MetricR1, R2, R3, R4, R5, R8, R11, R14, R17, R20, R21, R24, R25, R28, R29, R32
11100nFCapacitor_SMD:C_0603_1608MetricC1, C2, C6, C8, C13, C14, C15, C17, C29, C31, C32
8100KResistor_SMD:R_0603_1608MetricR6, R9, R12, R15, R37, R38, R39, R40
81KResistor_SMD:R_0603_1608MetricR7, R10, R13, R16, R18, R22, R26, R30
822.0uFCapacitor_SMD:C_1206_3216MetricC3, C4, C5, C9, C10, C11, C16, C28
8AUDIO JACK PJ-324M0AudioJacksFixed:pj324mJ4, J5, J6, J7, J8, J9, J10, J11
8Ceradiode 65VCapacitor_SMD:C_0603_1608MetricRV1, RV2, RV3, RV4, RV5, RV6, RV7, RV8
8LED 0402 GREENLED_SMD:LED_0402_1005MetricD3, D5, D7, D9, D11, D13, D15, D17
8LED 0402 REDLED_SMD:LED_0402_1005MetricD4, D6, D8, D10, D12, D14, D16, D18
8VBUS05L1LLP1006-2M:VISHAY-LLP1006-2MD27, D28, D29, D30, D31, D32, D33, D34
4120RResistor_SMD:R_Array_Convex_4x0402RN8, RN9, RN10, RN11
414.3KResistor_SMD:R_Array_Convex_4x0402RN1, RN2, RN3, RN4
4220pFCapacitor_SMD:C_0402_1005MetricC18, C19, C20, C21
456KResistor_SMD:R_0402_1005MetricR19, R23, R27, R31
456pCapacitor_SMD:C_0402_1005MetricC22, C23, C24, C25
4MMBFJ111Package_TO_SOT_SMD:SOT-23Q2, Q3, Q4, Q5
3100KResistor_SMD:R_Array_Convex_4x0402RN5, RN6, RN7
215V 200mAFuse:Fuse_0805_2012MetricF2, F3
22.2uFCapacitor_SMD:C_1206_3216MetricC7, C12
2560RResistor_SMD:R_Array_Convex_4x0402RN12, RN13
2FERRITEInductor_SMD:L_0603_1608MetricL1, L2
2MountingHole_PadMountingHole:MountingHole_2.2mm_M2_Pad_ViaH1, H2
2Nexperia PMEG6010CEH,115Diode_SMD:D_SOD-123FD1, D2
2TL074 OP AMPPackage_SO:SOIC-14_3.9x8.7mm_P1.27mmU2, U3
1100KResistor_SMD:R_0402_1005MetricR35
110KResistor_SMD:R_0402_1005MetricR36
11uFCapacitor_SMD:C_0805_2012MetricC33
12.2nFCapacitor_SMD:C_0402_1005MetricC30
124AA025UIDT EEPROMPackage_TO_SOT_SMD:SOT-23-6U5
12N7002EPackage_TO_SOT_SMD:SOT-23Q1
133RResistor_SMD:R_0402_1005MetricR34
1402KResistor_SMD:R_0402_1005MetricR43
1470RResistor_SMD:R_0402_1005MetricR33
1AK4619VN AUDIO CODECPackage_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.7x3.7mm_ThermalViasU1
1AZ1117-3.3Package_TO_SOT_SMD:SOT-89-3U8
1CONN 2x5 P=2.54mmConnector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_HorizontalJ1
1CONN 2x6 P=2.54mmConnector_PinHeader_2.54mm:PinHeader_2x06_P2.54mm_HorizontalJ2
1CY8CMBR3116Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mmU7
1Conn_01x14_Socketffc-ctxj:FFC_0.5-14P_CTXJ-H2.0_1J3
1LTV-357TPackage_SO:SO-4_4.4x3.6mm_P2.54mmU11
1PCA9557PW IO EXPANDERPackage_SO:TSSOP-16_4.4x5mm_P0.65mmU4
1PCA9635 LED DRIVERPackage_SO:TSSOP-28_4.4x9.7mm_P0.65mmU10
1TCM809S (2.93V)Package_TO_SOT_SMD:SOT-23U6
1TL072 OP AMPPackage_SO:SOIC-8_3.9x4.9mm_P1.27mmU9
1X.XResistor_SMD:R_0402_1005MetricR42

The 153 most common of 155 parts.

More from apfaudio/eurorack-pmod

3
  • 4 layers31.7 × 110 mmEurorack pmod pcb, the printed circuit board in 3D

    Eurorack pmod pcb

    apfaudio/eurorack-pmod

    A eurorack-friendly audio frontend compatible with many FPGA boards, based on the AK4619VN audio CODEC.

    126 parts241
  • 4 layers35 × 110 mmEurorack pmod pcb, the printed circuit board in 3D

    Eurorack pmod pcb

    apfaudio/eurorack-pmod

    A eurorack-friendly audio frontend compatible with many FPGA boards, based on the AK4619VN audio CODEC.

    125 parts241
  • 4 layers40 × 110 mmEurorack pmod pcb, the printed circuit board in 3D

    Eurorack pmod pcb

    apfaudio/eurorack-pmod

    A eurorack-friendly audio frontend compatible with many FPGA boards, based on the AK4619VN audio CODEC.

    104 parts241

Similar boards

  • 4 layers100 × 50 mmSuperball powerboard, the printed circuit board in 3D

    Superball powerboard

    kcaluwae/tensegrity-powerboard

    pcb design for the SUPERball power board

    161 parts1
  • 2 layers58 × 110 mmVco core, the printed circuit board in 3D

    Vco core

    shmoergh/moduleur

    Fully analog DIY-friendly modular synth

    146 parts222
  • 2 layers215 × 100 mmCore, the printed circuit board in 3D

    Core

    shmoergh/hog

    Fully analog two-voice monophonic synth for live performances

    370 parts124
  • 2 layers60 × 80 mmKeithley1950, the printed circuit board in 3D

    Keithley1950

    openscopeproject/Keithley1950

    Keithley 195A DMM Option 1950

    92 parts9
  • 2 layers100 × 88 mmHootswitch, the printed circuit board in 3D

    Hootswitch

    saybur/hootswitch

    ADB keyboard/mouse switch for vintage Mac computers.

    127 parts24
  • 4 layers60 × 30 mmDALI USB, the printed circuit board in 3D

    DALI USB

    SvenHaedrich/kicad_dali_usb_lpc

    KiCad Project for DALI to USB interface based on NXP LPC 1114 µController.

    47 parts3MIT
  • 2 layers50.8 × 25.4 mmCkt irsense split, the printed circuit board in 3D

    Ckt irsense split

    IowaScaledEngineering/ckt-irsense

    CKT-IRSENSE Reflective Infrared Proximity Sensor

    26 parts1
  • 2 layers70.6 × 90.9 mmISO11446PWR01, the printed circuit board in 3D

    ISO11446PWR01

    mlab-modules/ISO11446PWR01

    Car trailer emulator for use trailer socket as a power source

    70 parts1GPL-3.0

Questions

How big is the Eurorack pmod pcb PCB?

It measures 31.7 × 110 mm and has 6 copper layers, 1.6 mm thick.

What parts does the Eurorack pmod pcb use?

155 parts, built around the LTV-357T, VBUS05L1-DD1, MMBFJ111 and 2N7002E. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Eurorack pmod pcb KiCad files?

From the apfaudio/eurorack-pmod repository on GitHub, at the commit this page was made from: the board is hardware/eurorack-pmod-r3.5/eurorack-pmod-pcb.kicad_pcb and its schematic hardware/eurorack-pmod-r2.2/dual_mono_inputs.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Eurorack pmod pcb design in my own project?

Its repository states no licence, so its author keeps all rights: ask apfaudio before reusing the design.