Skip to the content
2 layers48 × 43 mmIEC Extension, the printed circuit board in 3D

IEC Extension

roberto314/Unicomp3

A modular 8-bit Computer able to recreate (nearly) every Retro computer of the late 70s to mid 80s.

Size
48 × 43 mm
Copper layers
2
Thickness
1.6 mm
Parts
32
Nets
51
Pads
178
Tracks, vias
510, 49
Pours
1
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
27 May 2024
Updated
13 Mar 2025

Overview

IEC Extension is an open-source printed circuit board by roberto314, from the roberto314/Unicomp3 repository on GitHub, published under the BSD-2-Clause licence. It is a 2-layer board of 48 × 43 mm with 32 parts on 51 nets, routed with 510 tracks and 49 vias.

It is built around the 74LS14PC. Its parts include 17 resistors, 7 capacitors, 4 ICs and 4 connectors. It belongs with the retro computing and games boards and the FPGA and CPLD boards of this library.

Main components

1

README

README.md

UNICOMP

Version 3.00

A modular 8-bit Computer able to recreate (nearly) every microcomputer of the mid 70s to early 80s in Hardware without FPGAs (although an FPGA can be added). Can also be used as a teaching tool for:

  • VHDL or Verilog
  • C
  • RTOS (STM32F401 runs ChibiOS. Link: https://www.chibios.org)
  • Python
  • bash and linux in general (Olimex board runs linux with fbterm and tmux)
  • Harwaredesign
  • Timing of CPUs
  • maybe Assembler
  • SPI and I2C Interfaces
  • CPLDs and FPGAs

It is different from other designs because of these points:

  • it uses a 3.3V only Bus,
  • it uses fast RAM for 16 chipselect outputs with single address resolution over the whole 1MB range,
  • it uses one SRAM for RAM and ROM replacement (can be write writeprotected) with 1MB,
  • it uses a clock generator chip (DS1085) - no more crystals to change,
  • it is configureable via STM32 (RAM and ROM content, Clock frequency, chip select lines),
  • it can program the CPLDs (only XC9572 and XC9536 tested) from the STM32, no external programmer needed.
  • Board size is 100mm x 100mm - no backplane (like the PC/104 standard. Link: https://en.wikipedia.org/wiki/PC/104).
  • and maybe most convenient: it can change RAM and ROM content on the fly without crashing the CPU. For example starting the Apple I, going into Basic and uploading the program in about half a second is really nice.

Unicomp plus Logic Analyzer: Unicomp plus Logic analyzer

Unicomp modules

  • USB-Serial board:

    • a simple board with an universal 4x USB to UART module from ebay (FT4232).
  • CPU board:

    • can be any 8-bit CPU (6502, 6802, 6809, 68008, 6803, 8051,...)
    • a CPLD (XC9572) for clock generation and glue logic
  • Multi Serial boaŕd:

    • suggested chip select #0
    • can be used with the following serial interface chips: MC6850, MOS6551, MOS6552 or pin compatible
  • Multi Parallel boaŕd:

    • suggested chip select #1
    • can be used with the following parallel interface chips: MC6820, MC6821, MOS6520, MOS6521, MOS6522, MOS6526, MOS8520, MOS6532 in the first slot
    • the first slot can additionally mimic a MOS6530
    • the second slot can accommodate a MOS6522 or pin compatible
  • RAMROM board:

    • chip select fixed at #15 (for chipselect RAM or ROM) and #14 for Write Disable (High for ROM),
    • 1M of SRAM plus an extra 16-bit RAM for address decoding,
    • a STM32F401 'blackpill' board to fill the SRAMs with data over USB,
    • USB shell on the STM32 to change ROM content on the fly,
    • also configures the Address Range of all peripheral modules,
    • acts as a XSVF Player to program the CPLDs
  • Prototype board:

    • empty board for prototyping
    • no CPLD
  • MAX-II (EPM240) board:

    • CPLD plus Buffers
  • self made module:

    • chip select can be any non-used line in the Range from 0 to 13.
    • size is 100mm x 100mm
    • there is the prototype board in the repository for the position of the connectors and also the labels (pinout)

Configuration RAM

The configuration is done with 1Mx16 fast ram on the RAMROM board. It is configured from the STM32F401. The cs = 15 is for writing the main RAM, cs = 14 is the Write Disable. The rest is free.

Working Recreations of old computers (tested again with Unicomp3)

Nameprim. IOchips usedosweblink
Motorola MEK D2serialMC6802, MĆ6850newbug, xswtbug, mondebLink: https://www.retrotechnology.com/restore/smithbug.html
Motorola MEK D1serialMC6802, MĆ6821 (plus Arduino)MikbugLink: https://www.retrotechnology.com/restore/smithbug.html
SWTPC 6800serialMC6802, MĆ6821 (plus Arduino)MikbugLink: https://deramp.com/swtpc.com/
SWTPC 6800serialMC6802, MĆ6850SWTBUG, SWTBUGA, Mondeb, xSWTBUGLink: https://deramp.com/swtpc.com/
Heathkit ET3400serialMC6802, MĆ6850MITS BASIC, TSC MicroBASIC,...Link: https://github.com/jefftranter
HD6303 Board (Eric Klaus)serialHD6303 or MC6803Monitor +BASICLink: https://sites.google.com/site/ericmklaus/projects-1/hd6303cpuboard
MC3 ComputerserialHD6303 or MC6803MonitorLink: https://www.waveguide.se/?article=mc3-a-diy-8-bit-computer
Grant Searle 6809 boardserialMC6809E, MC6850MS BasicLink: http://searle.x10host.com/6809/Simple6809.html
Grant Searle 6502 boardserialMOS6502, MC6850OSI BasicLink: http://searle.x10host.com/6502/Simple6502.html
Daryl Rictor 6502 boardserialMOS6502, R6551SBC-2 (monitor only)Link: https://sbc.rictor.org/info2.html
Daryl Rictor 6502 boardserialMOS6502, MC6850SBC-2 (monitor only)Link: https://sbc.rictor.org/info2.html
SYM1serialMOS6502, UM6532SYM1 ( +BASIC +RAE)Link: http://retro.hansotten.nl/6502-sbc/synertek-sym-ktm/sym-1/
KIM1serialMOS6502, UM6532KIM1Link: http://retro.hansotten.nl/6502-sbc/kim-1-manuals-and-software/
Apple IserialMOS6502, MĆ6821 (plus Arduino)Wozmon + BASICLink: http://retro.hansotten.nl/6502-sbc/apple-1/
DREAM 6800BAS (Video)MC6802, MAX-IIDREAM operating System (Chip8)Link: http://www.mjbauer.biz/DREAM6800.htm
Psion Organizer ILCDHD6303Psion OSLink: https://www.jaapsch.net/psion/index.htm

python helper scripts

  • UC3_upload.py: multi-function script. up- or download RAM Content, write or read the clock chip, set the reset pin, upload configuration data from file, upload RAM data from file, gets version number,

  • UC3_make_uploadfile.py: creates an .ucb file for upload. It can have multiple RAM locations and lengths.

CPLD programming

Used Software and OS

Used Hardware

  • Oscilloscope: Rigol DS1054Z (4 channel)
  • Logic Analyzer: Hantek 4032L (32 channel)

History Lesson

The unicomp Project started a couple of years ago and is developed in my spare time. It is intended to be a module system to test out different hardware configurations or CPLD- or FPGA- extensions and to recreate old systems and test software and operating systems.

Differences Unicomp2 from Unicomp1:

  • chipselect not with CPLD but with RAM on every peripheral board - more flexible,
  • chipselect resolution improved to two,

Differences Unicomp3 from Unicomp2:

  • chipselect RAM is on RAMROM Board (16-bit wide) - that leads to:
  • simpler (and cheaper) peripheral modules,
  • no linux SBC needed,
  • CPLD programming from STM32 or with external programmer (JTAG Header on every CPU Module)
  • 3.3V Supply on RAMROM board,
  • RAM has now a backup battery (CR2032) battery,
  • improved documentation.

Parts

32
QtyValueFootprintReferences
161kResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR1, R2, R3, R4, R5, R6, R7, R8, R9, R10, R12, R13, R14, R15, R16, R17
7100nCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC1, C2, C5, C6, C7, C8, C9
2DIN-6C64_IEC:C64_IECJ1, J2
110kResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR11
174LS06Package_SO:SOIC-14_3.9x8.7mm_P1.27mmU2
174LS14Package_SO:SOIC-14_3.9x8.7mm_P1.27mmU1
1AZ1117CH2-33Package_TO_SOT_SMD:SOT-223-3_TabPin2U4
1JTAGConnector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_HorizontalJ3
1PIAConnector_PinHeader_2.54mm:PinHeader_2x14_P2.54mm_VerticalJ4
1XC9572VQ44Package_QFP:TQFP-44_10x10mm_P0.8mmU3

More from roberto314/Unicomp3

12
  • 2 layers100 × 100 mmWD1771 Board, the printed circuit board in 3D

    WD1771 Board

    roberto314/Unicomp3

    A modular 8-bit Computer able to recreate (nearly) every Retro computer of the late 70s to mid 80s.

    122 partsBSD-2-Clause
  • 2 layers100 × 100 mmRAMROM Board, the printed circuit board in 3D

    RAMROM Board

    roberto314/Unicomp3

    A modular 8-bit Computer able to recreate (nearly) every Retro computer of the late 70s to mid 80s.

    105 partsBSD-2-Clause
  • 2 layers100 × 100 mm6809 CPU, the printed circuit board in 3D

    6809 CPU

    roberto314/Unicomp3

    A modular 8-bit Computer able to recreate (nearly) every Retro computer of the late 70s to mid 80s.

    103 partsBSD-2-Clause
  • 2 layers100 × 100 mmRamRomBoard, the printed circuit board in 3D

    RamRomBoard

    roberto314/Unicomp3

    A modular 8-bit Computer able to recreate (nearly) every Retro computer of the late 70s to mid 80s.

    97 partsBSD-2-Clause
  • 2 layers100 × 100 mmSchematics v10, the printed circuit board in 3D

    Schematics v10

    roberto314/Unicomp3

    A modular 8-bit Computer able to recreate (nearly) every Retro computer of the late 70s to mid 80s.

    92 partsBSD-2-Clause
  • 2 layers100 × 100 mm6502 6800 CPU, the printed circuit board in 3D

    6502 6800 CPU

    roberto314/Unicomp3

    A modular 8-bit Computer able to recreate (nearly) every Retro computer of the late 70s to mid 80s.

    91 partsBSD-2-Clause
  • 2 layers100 × 100 mmMMU v1, the printed circuit board in 3D

    MMU v1

    roberto314/Unicomp3

    A modular 8-bit Computer able to recreate (nearly) every Retro computer of the late 70s to mid 80s.

    90 partsBSD-2-Clause
  • 2 layers100 × 100 mmVideoBoard v1, the printed circuit board in 3D

    VideoBoard v1

    roberto314/Unicomp3

    A modular 8-bit Computer able to recreate (nearly) every Retro computer of the late 70s to mid 80s.

    86 partsBSD-2-Clause
  • 2 layers100 × 100 mmMP Board, the printed circuit board in 3D

    MP Board

    roberto314/Unicomp3

    A modular 8-bit Computer able to recreate (nearly) every Retro computer of the late 70s to mid 80s.

    71 partsBSD-2-Clause
  • 2 layers100 × 100 mmMOT Serial v11, the printed circuit board in 3D

    MOT Serial v11

    roberto314/Unicomp3

    A modular 8-bit Computer able to recreate (nearly) every Retro computer of the late 70s to mid 80s.

    68 partsBSD-2-Clause
  • 2 layers66.5 × 50.5 mm6303X FP64, the printed circuit board in 3D

    6303X FP64

    roberto314/Unicomp3

    A modular 8-bit Computer able to recreate (nearly) every Retro computer of the late 70s to mid 80s.

    60 partsBSD-2-Clause
  • 2 layers100 × 100 mmCpu template with buffer, the printed circuit board in 3D

    Cpu template with buffer

    roberto314/Unicomp3

    A modular 8-bit Computer able to recreate (nearly) every Retro computer of the late 70s to mid 80s.

    58 partsBSD-2-Clause

Similar boards

  • 2 layers231.1 × 106.7 mmSnark barker, the printed circuit board in 3D

    Snark barker

    schlae/snark-barker

    A 100% compatible replica of the famed SB 1.0 sound card

    199 parts687
  • 2 layers304.8 × 165.1 mmComix-35, the printed circuit board in 3D

    Comix-35

    schlae/comix-35

    The COMIX-35 is an improved clone of the COMX-35 1802 home computer

    173 parts138
  • 4 layers184.9 × 243.8 mmProject NuXT, the printed circuit board in 3D

    Project NuXT

    monotech/NuXT

    MicroATX Turbo XT Motherboard, with VGA, Floppy, CF, Serial

    223 parts121GPL-3.0
  • 4 layers62.5 × 83.8 mmKerberos2, the printed circuit board in 3D

    Kerberos2

    FrankBuss/kerberos

    C64/C128 MIDI flash interface

    169 parts81
  • 2 layers170.2 × 100 mmZ80-SBC, the printed circuit board in 3D

    Z80-SBC

    skiselev/zeta_sbc

    Zeta SBC is an Zilog Z80 based single board computer. It is inspired by Ampro Little Board Z80 and N8VEM project. Zeta SBC is software compatible with RomWBW Firmware

    75 parts53GPL-3.0
  • 2 layers33.7 × 56.5 mmLumafix, the printed circuit board in 3D

    Lumafix

    tebl/C64-Lumafix

    An easier to solder version of the Lumafix board, components spaced out a bit more to make things easier on the beginner (mostly meaning me).

    12 parts39
  • 2 layers162.2 × 134.6 mmSg1000, the printed circuit board in 3D

    Sg1000

    barbeque/sg1000

    A homebrew Sega SG-1000, with an eye towards SC-3000 compatibility

    89 parts33
  • 4 layers170 × 181 mm3ric, the printed circuit board in 3D

    3ric

    ebadger/3ric

    3ric homebrew computer repository

    150 parts32

Questions

How big is the IEC Extension PCB?

It measures 48 × 43 mm and has 2 copper layers, 1.6 mm thick.

What parts does the IEC Extension use?

32 parts, built around the 74LS14PC. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the IEC Extension KiCad files?

From the roberto314/Unicomp3 repository on GitHub, at the commit this page was made from: the board is ParallelBoards/IEC_Extension/IEC_Extension_v1.0/IEC_Extension.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the IEC Extension design in my own project?

Its repository publishes it under the BSD-2-Clause licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).