

Esp32 sensornode
Crowdsourced Environmental Sensing
- Size
- 70 × 33 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 38
- Nets
- 61
- Pads
- 195
- Tracks, vias
- 641, 84
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 6 May 2019
- Updated
- 1 Apr 2020
Overview
Esp32 sensornode is an open-source printed circuit board by rmd6502, from the rmd6502/envirosense repository on GitHub, published under the Apache-2.0 licence. It is a 2-layer board of 70 × 33 mm with 38 parts on 61 nets, routed with 641 tracks and 84 vias.
It is built around the CH330N, ESP32-WROOM-32 and BME280, with the BQ24075RGT, LM1117-3.3 and MMBT2222A among its other parts. Its parts include 12 resistors, 7 connectors, 6 ICs, 5 capacitors and 5 transistors. It belongs with the home automation and IoT boards and the ESP32 boards of this library.
Main components
7CH330N
SOP-8-20℃~+70℃ 15mA 2Mbps 3.3V、5V Transceiver SOP-8 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB ConvertersESP32-WROOM-32
SMD,18x25.5mm-40℃~+85℃ -98dBm 2.4GHz 2.7V~3.6V 20dBm Bluetooth4.2 ESP32-DOWDQ6 UART、SDIO、SPI、I2C、GPIO、PWM、ADC、DAC SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesBME280
LGA-8(2.5x2.5)-40℃~+85℃ 0%RH~100%RH 1.71V~3.6V 1.8uA 16bit I2C、SPI ±0.5℃ ±3%RH LGA-8(2.5x2.5) Temperature and Humidity Sensor ROHSBoschTemperature And Humidity SensorBQ24075RGT
QFN-16-EP(3x3)-40℃~+125℃ 1.5A 4.2V 4.35V~6.4V 6.5uA Charging IC Lithium Battery Not supported Support QFN-16-EP(3x3) Battery Management ROHSTexas InstrumentsBattery ManagementLM1117-3.3
SOT-2231 1.3V@(1000mA) 15V 1A 2mA 3.3V Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHShongjiachengUncategorisedMMBT2222A
SOT-23-55℃~+150℃ 1 NPN 100 100nA 1V 300MHz 300mW 40V 600mA 6V NPN Standalone SOT-23 Bipolar (BJT) ROHShongjiachengBipolar (BJT)MMDT2222A
SOT-363-55℃~+150℃ 10nA 1V 2 NPN 200mW 300 300MHz 40V 600mA 6V NPN SOT-363 Bipolar (BJT) ROHShongjiachengBipolar (BJT)
README
README.mdenvirosense
Crowdsourced Environmental Sensing

The pm (particulate measure) depends on Paul Van Haastrecht's SPS30 library at https://github.com/paulvha/sps30. Sensirion's library doesn't work, though I imagine they'll fix that.
Parts
38| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 10k | Resistor_SMD:R_0603_1608Metric | R3, R4, R7, R8, R9, R10, R12 |
| 3 | 220R | Resistor_SMD:R_0603_1608Metric | R1, R2, R11 |
| 3 | NDS3332P | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3 |
| 2 | 2.2u 10v | Capacitor_SMD:C_0603_1608Metric | C1, C4 |
| 2 | Conn_02x03_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J6, J7 |
| 1 | 1.13k | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | 1.18k | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 10u 10v | Capacitor_SMD:C_0603_1608Metric | C2 |
| 1 | 10u 5v | Capacitor_SMD:C_0603_1608Metric | C5 |
| 1 | 2.2u 5v | Capacitor_SMD:C_0603_1608Metric | C3 |
| 1 | BME280 | Package_LGA:Bosch_LGA-8_2.5x2.5mm_P0.65mm_ClockwisePinNumbering | U2 |
| 1 | BQ24075 | Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm_ThermalVias | U3 |
| 1 | CH330N | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | Conn_01x02_Male | Connector_JST:JST_EH_S2B-EH_1x02_P2.50mm_Horizontal | J5 |
| 1 | Conn_01x06_Female | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J1 |
| 1 | Conn_01x07_Male | Connector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_Vertical | J2 |
| 1 | ESP32-WROOM-32 | RF_Module:ESP32-WROOM-32 | U1 |
| 1 | LM1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U5 |
| 1 | LOGO | progcode-resources:pc3 | G*** |
| 1 | LOGO | logo:diamond | G*** |
| 1 | MMBT2222A | Package_TO_SOT_SMD:SOT-23 | Q5 |
| 1 | MMDT2222A | Package_TO_SOT_SMD:SOT-363_SC-70-6 | Q4 |
| 1 | Micro_SD_Card | Connector_Card:microSD_HC_Wuerth_693072010801 | J3 |
| 1 | TPS3839DBZ | Package_TO_SOT_SMD:SOT-23 | U6 |
| 1 | USB_B_Mini | Connector_USB:USB_Mini-B_Lumberg_2486_01_Horizontal | J4 |
The 37 most common of 38 parts.
More from rmd6502/envirosense
1- 2 layers35.7 × 21.5 mm

Similar boards
- 2 layers

- 2 layers90 × 80 mm

VLAD
icl-rocketry/VLAD-CanSat
Repository Containing the hardware and firmware of VLAD, a stabby boi who will participate in the Mach-21 CanSat competition
103 parts1 - 2 layers100.1 × 99.9 mm

- 2 layers60 × 40 mm

Forcegauge
szbeni/forcegauge
Traning for climbing. Load cell with HX711 and real time plotting,
77 parts18GPL-3.0 - 2 layers38.5 × 43 mm

Stepper monitor
zapta/ble_stepper_motor_analyzer
A low cost stepper motor analyzer that uses wireless BLE link to display the data in real time on a Windows/Mac/Linux PC.
58 parts58 - 2 layers60 × 60 mm

SolarpowerPCB
icl-rocketry/ICARUS
Imperial College london rocketry Attempts to be Resourceful by Using Solar power. A CanSat for the Mach-22 Competition
142 parts - 4 layers100 × 60 mm

- 2 layers330.8 × 114.9 mm

Questions
How big is the Esp32 sensornode PCB?
It measures 70 × 33 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Esp32 sensornode use?
38 parts, built around the CH330N, ESP32-WROOM-32, BME280 and BQ24075RGT. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Esp32 sensornode KiCad files?
From the rmd6502/envirosense repository on GitHub, at the commit this page was made from: the board is esp32_sensornode/esp32_sensornode.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Esp32 sensornode design in my own project?
Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).