
Hub16
joshajohnson/Hub16
A macro pad with 16 keys, two rotary encoders, a four port USB hub, and plenty of LEDs!

Custom Cherry G80-1800 Keyboard Project
Gh80-1800 is an open-source printed circuit board by retoid, from the retoid/G80-1800-Retoid repository on GitHub. It is a 2-layer board of 381 × 148.2 mm with 249 parts on 146 nets, routed with 1,579 tracks and 183 vias.
It is built around the ATMEGA32U4. Its parts include 104 switches, 103 diodes, 7 resistors, 6 capacitors and 6 inductors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Making a custom PCB for Cherry G80-1800 with hotswap socket compatibility.
This is a customized version of evyd13's files found here: GH80-1800
Note! I have removed the alternate positioning for varying layouts and included support for Kailh or Gateron Hotswap sockets. The firmware supports only this layout. The PCB supports PCB or Plate mount switches. However the Plate file supports only PCB mount stabilizers. Must use hotswap sockets, otherwise you will have to change the switch footprints to accept solder mount.
Versions V1.0 uses a different layout that utilizes a 6U Cherry Spacebar. But since these are rather difficult to come by, both 6U spacebar and 6U stabilizers. The updated V1.1 utilizes a 6.25U spacebar but eliminates a key and changes some key sizes on each side of the spacebar. V1.0 does not have the PCB mount support holes for switches.
Project Files are created with KiCad. Version: (5.99.0-7511-ga134567838), release build
| LCSC part # | Description | Value | Package | Amount |
|---|---|---|---|---|
| C128353 | Capacitor | 0.1uF | 0805 | 4 |
| C131056 | Capacitor | 4.7uF | 0805 | 1 |
| C215803 | Capacitor | 1uF | 0805 | 1 |
| C109001 | Diode | 0805 | 108 | |
| C105424 | Connector | SMD | 3 | |
| C103904 | Resistor | 10K | 0805 | 2 |
| C384174 | Resistor | 1K | 0805 | 3 |
| C325772 | Resistor | 22 | 0805 | 2 |
| C44854 | MCU | 32U4 | QFP-44 | 1 |
| C341521 | Resonator | 16MHz | SMD | 1 |
| C92584 | Switch | SMD | 1 | |
| Kailh/Gateron | Hotswap socket | SMD | 108 |
| Qty | Value | Footprint | References |
|---|---|---|---|
| 103 | D | Diode_SMD:D_0805_2012Metric | D1, D10, D11, D12, D13, D14, D15, D101, D102, D103, D104, D105, D107, D108, D109, D110 +87 |
| 98 | KEYSW | Keyswitches:Kailh_socket_MX_PinSwap | K1, K10, K11, K12, K13, K14, K15, K101, K102, K103, K104, K105, K107, K108, K109, K110 +82 |
| 7 | 4mm_hole | footprints:4mm_hole | H1, H2, H4, H6, H7, H10, H12 |
| 4 | 0.1u | Keeb_components:C_0805 | C103, C104, C105, C106 |
| 3 | 1k | Keeb_components:R_0805 | R106, R107, R108 |
| 3 | LED | Keeb_switches:CHERRY_MX_LED | L1-1, L2-2, L3-1 |
| 3 | LED | Keeb_components:LED_D3.0mm | L1, L2, L3 |
| 3 | USB_mini_micro_B | Keeb_components:USB_Mini_SMD | J1, J4, J5 |
| 2 | 10k | Keeb_components:R_0805 | R101, R102 |
| 2 | 22 | Keeb_components:R_0805 | R103, R104 |
| 2 | 4x8mm_hole | footprints:4x8mm_hole | H11, H13 |
| 2 | KEYSW | Keyswitches:Kailh_socket_MX_2U_PinSwap | K18, K77 |
| 2 | KEYSW | Keyswitches:Kailh_socket_MX_225U_PinSwap | K73, K89 |
| 1 | 1u | Keeb_components:C_0805 | C108 |
| 1 | 3x5mm_hole | footprints:3x5mm_hole | H8 |
| 1 | 4.5mm_hole | footprints:4.5mm_hole | H9 |
| 1 | 4.7u | Keeb_components:C_0805 | C107 |
| 1 | 6mm_hole | footprints:6mm_hole | H3 |
| 1 | 6x10mm_hole | footprints:6x10mm_hole | H5 |
| 1 | ATmega32U4 | Keeb_components:ATMEGA32U4 | U1 |
| 1 | ISP | Keeb_components:isp_standard | J2 |
| 1 | KEYSW | Keyswitches:Kailh_socket_MX_625U_PinSwap | K97 |
| 1 | LOGO | Keyswitches:Eighteen_Hundred_Logo | G*** |
| 1 | LOGO | Keyswitches:Cherries_Halftone_Logo | G*** |
| 1 | SW_Push | Buttons_Switches_SMD:SW_SPST_TL3342 | SW1 |
| 1 | USB Header | Keeb_components:USB_breakout | J3 |
| 1 | XTAL_GND | Crystal:Resonator_SMD_Murata_CSTxExxV-3Pin_3.0x1.1mm_HandSoldering | X1 |
The 248 most common of 249 parts.

joshajohnson/Hub16
A macro pad with 16 keys, two rotary encoders, a four port USB hub, and plenty of LEDs!

tmk/USB2USB_Converter
USB to USB keyboard protocol converter supported by TMK keyboard firmware



evyd13/gh80-series
GH80-1800, GH80-3700 and GH80-3003 by Evy (aka anykeys.eu)



It measures 381 × 148.2 mm and has 2 copper layers, 1.6 mm thick.
249 parts, built around the ATMEGA32U4. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the retoid/G80-1800-Retoid repository on GitHub, at the commit this page was made from: the board is PCB/gh80-1800.kicad_pcb and its schematic PCB/gh80-1800.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask retoid before reusing the design.