
Helena base sd
Reisi/Helena
Helena is an alternative driver for the Yinding or KD2 Headlight Cycling Lamp.

Helena is an alternative driver for the Yinding or KD2 Headlight Cycling Lamp.
Helena ctrl is an open-source printed circuit board by Reisi, from the Reisi/Helena repository on GitHub, published under the BSD-2-Clause licence. It is a 2-layer board of 29 × 18 mm with 27 parts on 26 nets, routed with 257 tracks and 52 vias.
It is built around the MPU-6050. Its parts include 7 capacitors, 6 resistors, 2 diodes, 2 connectors and 1 IC. It belongs with the nRF52 and nRF5x boards of this library.

Helena is an alternative driver for the Yinding or KD2 Headlight Cycling Lamp.
This project is licensed under the BSD-2-clause License - see the license.txt file for details
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 100n | Capacitor_SMD:C_0603_1608Metric | C2, C13, C15, C16 |
| 2 | 1k5 | Resistor_SMD:R_0603_1608Metric | R3, R5 |
| 2 | FB | Inductor_SMD:L_0603_1608Metric | FB1, FB2 |
| 1 | 100k | Resistor_SMD:R_0603_1608Metric | R2 |
| 1 | 10n | Capacitor_SMD:C_0603_1608Metric | C14 |
| 1 | 120 | Resistor_SMD:R_0603_1608Metric | R7 |
| 1 | 2n2 | Capacitor_SMD:C_0603_1608Metric | C17 |
| 1 | 2u2/16 | Capacitor_SMD:C_0603_1608Metric | C1 |
| 1 | 470k | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 680 | Resistor_SMD:R_0603_1608Metric | R4 |
| 1 | CONN_01X06 | Connector_PinHeader_2.00mm:PinHeader_1x06_P2.00mm_Vertical | J1 |
| 1 | CONN_02X05 | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical | J2 |
| 1 | LED_BLUE | Diode_SMD:D_0603_1608Metric | D2 |
| 1 | LED_RED | Diode_SMD:D_0603_1608Metric | D1 |
| 1 | LOGO | rt_Logos:Helena_5,0x4,1mm | G*** |
| 1 | MPU-6050 | rt_Housing_QFN_DFN:QFN-24-1EP_4x4mm_Pitch0.5mm | U1 |
| 1 | SW_PUSH | rt_button:JTP-1138EM | SW1 |
| 1 | nrf51822-04AT_Module | WT51822-S4AT | A1 |
The 23 most common of 27 parts.

Reisi/Helena
Helena is an alternative driver for the Yinding or KD2 Headlight Cycling Lamp.

Reisi/Helena
Helena is an alternative driver for the Yinding or KD2 Headlight Cycling Lamp.

Reisi/Helena
Helena is an alternative driver for the Yinding or KD2 Headlight Cycling Lamp.


ZhuYanzhen1/MM32_CLion
本项目是全国大学生智能车竞赛GDUT 2022年极速越野组的项目文件。采用了LQR控制器和多速率卡尔曼融合算法,并在单片机上实现。This project is the project document for the GDUT 2022 Extreme Off-Road Category of the National Student Intelligent Vehicle Competition.


victorhook/asac-fc
asac fc is an rp2040 based flight controller made for FPV drone flying




pms67/PModlet
PMOD PCB with USB-to-UART converter and IMU (MPU-6050, I2C) for FPGAs.
It measures 29 × 18 mm and has 2 copper layers, 0.8 mm thick.
27 parts, built around the MPU-6050. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Reisi/Helena repository on GitHub, at the commit this page was made from: the board is Hardware/Ctrl/Helena_ctrl.kicad_pcb and its schematic Hardware/LED_Boards/XHP35_XHP50_KD2/XHP35_XHP50_KD2.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the BSD-2-Clause licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).