Skip to the content
2 layers100 × 100 mmPanel ESPSomfy RTS, the printed circuit board in 3D

Panel ESPSomfy RTS

rdalen/myESPSomfyRTS

A DIY controller to operate my SunRain shade, based on the open-source ESPSomfyRTS software

Size
100 × 100 mm
Copper layers
2
Thickness
1.6 mm
Parts
280
Nets
184
Pads
576
Tracks, vias
496, 24
Pours
8
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
17 Sep 2026
Updated
24 Oct 2026

Overview

Panel ESPSomfy RTS is an open-source printed circuit board by rdalen, from the rdalen/myESPSomfyRTS repository on GitHub. It is a 2-layer board of 100 × 100 mm with 280 parts on 184 nets, routed with 496 tracks and 24 vias.

It is built around the CC1101RGP. Its parts include 16 ICs, 8 capacitors, 8 resistors and 8 diodes. It belongs with the ESP32 boards of this library.

Main components

1

README

README.md

myESPSomfyRTS

A DIY Somfy RTS controller for my SunRain Awning/Shade, based on the open-source ESPSomfyRTS project.

The controller uses an ESP32 together with a CC1101 433 MHz RF transceiver and integrates with my Home Assistant and Node-RED setup.

image

Architecture diagram

How It Works

  • Hardware: ESP32 microcontroller paired with a CC1101 radio transceiver module.
  • Communication: Connects to my home Wi-Fi network and sends 433 MHz radio signals compatible with the Somfy RTS (Radio Technology Somfy) protocol.
  • Local Operation: ESPSomfyRTS provides a built-in web interface for controlling the shade directly from a phone or computer.
  • Smart Home Integration: The controller integrates with Home Assistant and Node-RED for automation and monitoring.
  • Position Tracking: Tracks the shade position independently of the physical Somfy remote.

For the firmware, general wiring information and ESPSomfyRTS documentation, see the official ESPSomfyRTS project.

An instruction video is available on YouTube.


Repository Contents

This repository contains the files specific to my implementation:

  • 📁 KiCad — Schematic and PCB design files
  • 📁 nodeRed — Node-RED flows used for control, monitoring and automation

The ESP32 firmware itself is based on the ESPSomfyRTS project.


CC1101 433 MHz RF Transceiver

CC1101 RF transceiver E07-M1101D-SMA module

My version of the CC1101-based module (E07-M1101D-SMA) exposes only a single GDO line, while ESPSomfyRTS is often configured with separate RX and TX signal pins.

By assigning both RX and TX to the same GPIO, ESPSomfyRTS can use the single GDO line for both receiving and transmitting.

The GPIO configuration with the Seeed Studio XIAO ESP32-S3 is:

  • RX Pin = GPIO3
  • TX Pin = GPIO3 ← same GPIO as RX

ESP32-S3 XIAO

Pin connections between the CC1101 module and the XIAO ESP32-S3:

XIAO ESP32-S3 pinout
CC1101 PinDescriptionESP SignalESP Pin
1GNDGND13
2VCC3V312
3GDO0 - RX/TXGPIO 033
4CSNGPIO 066
5SCKGPIO 079
6MOSIGPIO 0911
7MISOGPIO 0810
8Not connected

Here is the corresponding ESPSomfyRTS radio configuration:

ESPSomfyRTS radio configuration

Schematic & PCB

I designed a small custom PCB for the controller.

The complete KiCad project is available in the KiCad folder.

PCB ESPSomfyRTS PCB layout image PCB image PCB

Before ordering, I panelized the PCB design so I have several boards available for experimenting with and sharing.

image

Enclosure

Finally, I "Boxified" an enclosure for the controller using my Boxify Parametric Electronics Enclosure Framework.

See also my Boxify Instructable.

The enclosure was then 3D printed.

The STL files are available in the Enclosure folder of this repository, so you can print your own enclosure without having to generate the models yourself.

The folder contains the STL files for the box base, lid, adapter plate, and text labels.

3D printed enclosure Enclosure

Controlling the SunRain Shade

The Somfy motor does not provide a motor-running feedback signal.

I therefore derive the motor-running state from a HomeWizard Energy Socket. The motor uses approximately 200 W while running, making it possible to detect whether the motor is active.

image

For controlling and monitoring the shade I created a Node-RED dashboard.

The complete Node-RED flow is available in the nodeRed folder.

The dashboard allows me to:

  • control the shade
  • monitor whether the motor is responding
  • track the shade position
  • detect when the motor is running
  • receive a warning when rain is predicted within 30 minutes
Node-RED dashboard

Parts

280
QtyValueFootprintReferences
224NPTHNPTHKiKit_MB_10_2, KiKit_MB_10_3, KiKit_MB_10_4, KiKit_MB_10_5, KiKit_MB_10_6, KiKit_MB_10_7, KiKit_MB_10_8, KiKit_MB_11_2, KiKit_MB_11_3, KiKit_MB_11_4, KiKit_MB_11_5, KiKit_MB_11_6, KiKit_MB_11_7, KiKit_MB_11_8, KiKit_MB_12_2, KiKit_MB_12_3 +208
8100n01-myFootprints:C-Common-THT-P5.08mmC1, C1, C1, C1, C1, C1, C1, C1
81k01-myFootprints:R-Common-THT-P10.16mmR1, R1, R1, R1, R1, R1, R1, R1
8CC110101-myFootprints:MOD-CC1101U2, U2, U2, U2, U2, U2, U2, U2
8ESP32-S3 Xiao01-myFootprints:MOD-ESP32-S3-XIAO-DIPU1, U1, U1, U1, U1, U1, U1, U1
8LED01-myFootprints:LED-D3.0mmD1, D1, D1, D1, D1, D1, D1, D1
8Logo-RvD01-myFootprints:LOGO-RvD-inverted-smallLogo1, Logo1, Logo1, Logo1, Logo1, Logo1, Logo1, Logo1
8Logo-TechDen01-myFootprints:LOGO-TechDen-invertedLogo2, Logo2, Logo2, Logo2, Logo2, Logo2, Logo2, Logo2

More from rdalen/myESPSomfyRTS

1
  • 2 layers49 × 23.5 mmESPSomfy RTS, the printed circuit board in 3D

    ESPSomfy RTS

    rdalen/myESPSomfyRTS

    A DIY controller to operate my SunRain shade, based on the open-source ESPSomfyRTS software

    7 parts

Similar boards

  • 2 layers70 × 70 mmMicroNet Teensy4, the printed circuit board in 3D

    MicroNet Teensy4

    Rodemfr/MicronetToNMEA

    A NMEA 0183 converter for Raymarine's wireless instruments ... and much more !

    13 parts34GPL-3.0
  • 2 layersHB LC Dim6PWM CV, the printed circuit board in 3D

    HB LC Dim6PWM CV

    stan23/myPCBs

    Verschiedene Platinen für HomeMatic, AskSinPP und SmartHome

    57 parts21
  • 2 layers61.4 × 103.3 mmHB Dis EP-42BW, the printed circuit board in 3D

    HB Dis EP-42BW

    jp112sdl/HB-Dis-EP-42BW

    4.2" ePaper Display mit 10 Tasterkanälen für Homematic

    45 parts18
  • 2 layers76.6 × 141.1 mmOniondao badge, the printed circuit board in 3D

    Oniondao badge

    OnionDAO-git/oniondao-badge

    An open-source, hacker-conference-style electronic badge built around the ESP32-S3-WROOM-1-N8R8 (8 MB flash + 8 MB Octal PSRAM), with swappable RF / audio / storage modules, an e-paper (or TFT) display socket, a secure…

    190 parts17
  • 2 layers99.9 × 40 mmHackbat, the printed circuit board in 3D

    Hackbat

    thehackbat/hackbat_esp32

    Hackbat version based on the ESP32C6

    68 parts12
  • 2 layers51 × 61 mmRHS 3, the printed circuit board in 3D

    RHS 3

    pa-pa/HB-Sec-RHS-3

    68 parts9
  • 2 layers17 × 19 mm328RFStamp, the printed circuit board in 3D

    328RFStamp

    jp112sdl/328RFStamp

    328RFStamp - Miniplatine für CC1101 und 328P

    20 parts8
  • 4 layers30 × 50 mmWireless logger, the printed circuit board in 3D

    Wireless logger

    bnahill/wireless_logger

    A compact wireless inertial logging and processing hardware platform

    155 parts7

Questions

How big is the Panel ESPSomfy RTS PCB?

It measures 100 × 100 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Panel ESPSomfy RTS use?

280 parts, built around the CC1101RGP. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Panel ESPSomfy RTS KiCad files?

From the rdalen/myESPSomfyRTS repository on GitHub, at the commit this page was made from: the board is KiCad/ESPSomfyRTS-Panel/Panel_ESPSomfy RTS.kicad_pcb and its schematic KiCad/ESPSomfy RTS.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Panel ESPSomfy RTS design in my own project?

Its repository states no licence, so its author keeps all rights: ask rdalen before reusing the design.