2 layers40 × 61 mm
2 layers90.2 × 54.6 mm
Tasarim 1 1
RasTm/FlyBoardBu proje uçuş kontrol kartımız için gerekli yazılımım içermektedir. Proje tamamlandıkça bu bölüm kullanım klavuzu olarak değiştirilecektir.
- Size
- 90.2 × 54.6 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 51
- Nets
- 123
- Pads
- 319
- Tracks, vias
- 574, 72
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 20 Jan 2023
- Updated
- 18 Oct 2026
Overview
Tasarim 1 1 is an open-source printed circuit board by RasTm, from the RasTm/FlyBoard repository on GitHub. It is a 2-layer board of 90.2 × 54.6 mm with 51 parts on 123 nets, routed with 574 tracks and 72 vias.
It is built around the MS5611-01BA03, AMS1117-3.3 and MPU-6050. Its parts include 24 capacitors, 9 connectors, 7 resistors, 5 ICs and 2 diodes. It belongs with the STM32 boards of this library.
Main components
3
MS5611-01BA03
QFN-8(3x5)QFN-8(3x5) Pressure Sensors ROHSMEASPressure Sensors
AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
MPU-6050
QFN-24-EP(4x4)-40℃~+85℃ 16bit 1KB 2.375V~3.46V 5uA Accelerometer Gyroscope I2C X,Y,Z X,Y,Z ±16g ±2000dps QFN-24-EP(4x4) Accelerometers ROHSTDK InvenSenseAccelerometers
README
README.mdBu proje uçuş kontrol kartımız için gerekli yazılımım içermektedir. Proje tamamlandıkça bu bölüm kullanım klavuzu olarak değiştirilecektir.
Projeyi Atollic ile derleyebilmek için aşağıdaki işlemler yapılmalıdır.
1- Proje açılırken executable değil makefile olarak açılmalıdır.
2- C++ sürümü Properties (Alt+Enter) / C,C++ Build / Settings / Tool Settings / C++ Compiler / General başlığı altından C++ 11 olarak ayarlanmalıdır.
3- Properties (Alt+Enter) / C,C++ General / Paths and Symbols başlığına gidilip Includes, Library Paths, Source Location sekmelerine Libs klasörü eklenmelidir.
4- Properties (Alt+Enter) / C,C++ General / Paths and Symbols başlığına gidilip Includes ve Symbols sekmelerinden STD_Lib ile alakalı her şey kaldırılmalıdır.
5- Libraries klasöründeki STD_periph klasörü kaldırılmalıdır.
6- Libraries/Cmsis klasörü içerisine DSP_Lib ve Include klasörleri atılmalıdır eğer uyarı verirse orijinal dosyaların üzerine yazılmalıdır.
7- stm32f4xx_conf.h dosyasında eklenmiş tüm Stdlib kütüphaneleri kaldırılmalıdır.
8- Float değerleri LCD ekran üzerine yazdırmak için snprint fonksiyonu modifiye edilmelidir. Bunun için Properties (Alt+Enter) / C,C++ Build / Settings / Tool Settings / C++ Linker başlığı içerisinde Command alt başlığına "-u_printf_float" ifadesi yazılmalıdır.
9- Debug ekranında başlatmadan önce main'de durmasını sağlayan breakpoint kaldırılmalı yoksa C++ ile geliştirme yaparken program kırılabilir. Kaldırmak için Configure Debug / Startup Scripts gidilmeli. Buranın en altından "# Set a breakpoint at main(). tbreak main" Silinmeli.
Parts
51| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 100nF | Capacitor_SMD:C_0603_1608Metric | C1, C4, C5, C6, C7, C8, C9, C10, C16, C17, C19, C21, C24 |
| 4 | 10uF | Capacitor_Tantalum_SMD:CP_EIA-1608-08_AVX-J | C14, C15, C22, C23 |
| 3 | 4.7K | Resistor_SMD:R_0603_1608Metric | R5, R6, R7 |
| 2 | 10K | Resistor_SMD:R_0603_1608Metric | R2, R3 |
| 2 | 1K | Resistor_SMD:R_0603_1608Metric | R1, R4 |
| 2 | 2.2uF | Capacitor_Tantalum_SMD:CP_EIA-1608-08_AVX-J | C12, C13 |
| 2 | 20pF | Capacitor_SMD:C_0603_1608Metric | C2, C3 |
| 2 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2, U5 |
| 2 | LED | LED_SMD:LED_0805_2012Metric | D1, D2 |
| 2 | TestPoint | TestPoint:TestPoint_Pad_D1.0mm | TP1, TP2 |
| 1 | 10nF | Capacitor_SMD:C_0603_1608Metric | C18 |
| 1 | 1uF | Capacitor_Tantalum_SMD:CP_EIA-1608-08_AVX-J | C11 |
| 1 | 2.2nF | Capacitor_SMD:C_0603_1608Metric | C20 |
| 1 | 8MHz | Crystal:Crystal_HC49-4H_Vertical | Y1 |
| 1 | APM_Connector | Connector_Hirose:Hirose_DF13-06P-1.25DSA_1x06_P1.25mm_Vertical | J8 |
| 1 | Boot_0 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | Bootloader_Port | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J7 |
| 1 | GPS_Connector | Connector_Hirose:Hirose_DF13-06P-1.25DSA_1x06_P1.25mm_Vertical | J6 |
| 1 | LORA_Connector | Connector_JST:JST_PH_B7B-PH-K_1x07_P2.00mm_Vertical | J3 |
| 1 | MPU-6050 | Sensor_Motion:InvenSense_QFN-24_4x4mm_P0.5mm | U3 |
| 1 | MS5611-01BA | Package_LGA:LGA-8_3x5mm_P1.25mm | U4 |
| 1 | NRF_Connector | Connector_JST:JST_PH_B8B-PH-K_1x08_P2.00mm_Vertical | J4 |
| 1 | STM32F407V_E-G_Tx | Package_QFP:LQFP-100_14x14mm_P0.5mm | U1 |
| 1 | SWD_Connector | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Horizontal | J1 |
| 1 | SW_Push | Button_Switch_THT:SW_PUSH_6mm_H5mm | SW1 |
| 1 | Telemetri | Connector_JST:JST_PH_B4B-PH-K_1x04_P2.00mm_Vertical | J9 |
| 1 | ZW-21-08-L-T-200-157 | 3x21 pin:SAMTEC_ZW-21-08-L-T-200-157 | J5 |
Questions
How big is the Tasarim 1 1 PCB?
It measures 90.2 × 54.6 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Tasarim 1 1 use?
51 parts, built around the MS5611-01BA03, AMS1117-3.3 and MPU-6050. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Tasarim 1 1 KiCad files?
From the RasTm/FlyBoard repository on GitHub, at the commit this page was made from: the board is PCB/tasarim_1_1.kicad_pcb and its schematic PCB/tasarim_1_1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Tasarim 1 1 design in my own project?
Its repository states no licence, so its author keeps all rights: ask RasTm before reusing the design.
Similar boards
- 2 layers131 × 100 mm
Panel
RamRamAndroid/ESP32Drone-CodeMatrix
ESP32 Drone by CodeMatrix is a compact, WiFi-controlled drone based on the ESP32-S3 microcontroller. Designed for hobbyists, makers, and engineers, ESP32 Drone by CodeMatrix offers a simple yet powerful platform for…
182 parts1 - 4 layers98 × 98 mm
Aquila main
cuspaceflight/aquila-avionics
Flight computer schematics and firmware for Aquila, the upper stage of Griffin 1
176 parts - 2 layers45 × 30 mm
- 4 layers93 × 93 mm
FCSat dual
SunnyYoshimitsu/Reconfigurable-Space-Compute-Cluster
Here will be the repository for an "extremely reconfigurable satellite" aimed toward at competing in NASA Minds and hopefully assist Artemis in its missions.
215 parts3 - 6 layers80 × 80 mm
V2ultimateflightcomp
codinga593/IRIS
A next generation model rocket focused on a precise propulsive landing on a tower.
144 parts3 - 4 layers55 × 154.1 mm
GPS module
Dizzerin/Rocket-Flight-Data-Computer
This project uses an STM32H743VGT6 MCU along with some innertial measurement units (IMU)s and barometric pressure sensors to and an SD card to record flight data from a model rocket and for later analysis, graphing, and…
161 parts1 - 4 layers128 × 84 mm
Dronemagnav2
ajisrawi/DroneMagNav2.0
DroneMagNav 2.0 - survey-fluxgate magnetic-anomaly navigation board for drones (IGRF-14 + EMAG2v3 continued to flight altitude)
222 parts