

Esp-32-board
Set of DIY hardware modules.
- Size
- 53.4 × 68.6 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 39
- Nets
- 57
- Pads
- 246
- Tracks, vias
- 418, 70
- Pours
- 8
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 27 Jan 2021
- Updated
- 12 Nov 2022
Overview
Esp-32-board is an open-source printed circuit board by rafw87, from the rafw87/hardware-modules repository on GitHub, published under the CC-BY-SA-4.0 licence. It is a 2-layer board of 53.4 × 68.6 mm with 39 parts on 57 nets, routed with 418 tracks and 70 vias.
It is built around the ESP32-WROOM-32, FT232RL and USBLC6-2SC6, with the RF-YUS150TS-AE and STPS0520Z among its other parts. Its parts include 11 capacitors, 7 connectors, 6 resistors, 5 ICs and 5 diodes. It belongs with the ESP32 and ESP8266 boards of this library.
Main components
5ESP32-WROOM-32
SMD,18x25.5mm-40℃~+85℃ -98dBm 2.4GHz 2.7V~3.6V 20dBm Bluetooth4.2 ESP32-DOWDQ6 UART、SDIO、SPI、I2C、GPIO、PWM、ADC、DAC SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesFT232RL
SSOP-28-208mil-40℃~+85℃ 3.3V~5.25V、4V~5.25V USB 2.0 USB to UART SSOP-28-208mil USB Converters ROHSFTDIUSB ConvertersUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)RF-YUS150TS-AE
1206-40℃~+85℃ 140° 20mA 90mW Discrete Diode Top-mount Yellow 1206 LED Indication - Discrete ROHSRefondLight Emitting Diodes (LED)STPS0520Z
SOD-1231 Independent 150uA@20V 20V 385mV@500mA 5.5A 500mA SOD-123 Schottky Diodes ROHSSTMicroelectronicsSchottky Diodes
README
modules/esp-32-board/README.mdESP-32 board on Arduino footprint
ESP-WROOM-32 (or ESP32-SOLO-1) development kit with Micro-USB port, DC Input and ESP-PROG interface.
Based on Arduino Uno/Leonardo footprint, so (apart from interesting appearance) allows to use stands and (partially) enclosures from original Arduino.
Note: It's not an Arduino clone, so it's not compatible (neither electrically nor physically) with Arduino shields. Functionally it's evaluation board like ESP32-DevKitC.


Resources
- Schematic
- BOM
- Project on PCBWay
- Gerbers
License

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Parts
39| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 0.1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C3, C4, C9, C11 |
| 3 | 220 Ohm | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R3, R4 |
| 3 | 22uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C5, C6, C10 |
| 2 | 10 kOhm | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5, R6 |
| 2 | 47uF | Capacitor_SMD:CP_Elec_5x5.9 | C7, C8 |
| 2 | RF-YUS150TS-AE | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D4, D5 |
| 2 | SW_Push | project_components:SW_Push_1P1T_NO_6x6mm_H4.3mm | SW1, SW2 |
| 1 | 100 Ohm | Resistor_SMD:R_Array_Convex_4x0612 | RN1 |
| 1 | 2.2 kOhm | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2 |
| 1 | 4.7uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1 |
| 1 | Arduino Footprint | project_components:ArduinoFootprint | N1 |
| 1 | BCR129S | Package_TO_SOT_SMD:SOT-363_SC-70-6 | Q1 |
| 1 | Barrel_Jack_MountingPin | project_components:BarrelJack_CLIFF_FC68148_Horizontal | J5 |
| 1 | Conn_01x06 | Connector_PinSocket_2.54mm:PinSocket_1x06_P2.54mm_Vertical | J3 |
| 1 | Conn_01x14_Female | Connector_PinSocket_2.54mm:PinSocket_1x14_P2.54mm_Vertical | J1 |
| 1 | Conn_01x18_Female | Connector_PinSocket_2.54mm:PinSocket_1x18_P2.54mm_Vertical | J2 |
| 1 | ESP-PROG-Debug | project_components:IDC-Header_2x05_P1.27mm_Vertical_SMD | J7 |
| 1 | ESP-PROG-Program | project_components:IDC-Header_2x03_P1.27mm_Vertical_SMD | J6 |
| 1 | ESP32-WROOM-32 | project_components:ESP32-WROOM-32-ThermalVias | U1 |
| 1 | FT232RL | Package_SO:SSOP-28_5.3x10.2mm_P0.65mm | U5 |
| 1 | M7 | Diode_SMD:D_SMA_Handsoldering | D2 |
| 1 | NCP1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | NCP1117ST50T3G | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | RF-GSS150TS-BC | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D1 |
| 1 | STPS0520Z | Diode_SMD:D_SOD-123 | D3 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U4 |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-B_Amphenol_10118194_Horizontal | J4 |
More from rafw87/hardware-modules
3- 2 layers65 × 56 mm

- 2 layers25.4 × 22.2 mm

- 2 layers20.8 × 18.3 mm

Similar boards
- 2 layers26 × 40 mm

Nervous EDA
sensors-inl/Nervous-EDA
ECAD design files, firmware source code and standalone application for the EDA sensor of the Nervous project.
55 parts3MIT - 2 layers26 × 40 mm

Nervous ECG
sensors-inl/Nervous-ECG
ECAD design files, firmware source code and standalone application for the ECG sensor of the Nervous project.
65 parts2MIT - 2 layers147 × 92 mm

Van
blinken/vandal
An ESP32-based lighting control system for campervans (or anything else)
227 parts6GPL-3.0 - 2 layers134.4 × 106.7 mm

Led controller
MbFredys/PCB-LEDs-Controller
LED-controller PCB design exercise focused on PWM control, power distribution, and hardware documentation.
42 parts6 - 2 layers98 × 187 mm

Projet
FranklinBerger/Polonise-Inverse
Projet électronique de calculatrice en Polonaise Inversse. Bassée sur un ESP32 sur firmware MicroPython, elle a été initialement conçue dans le cadre d'un stage de découverte de l'électronique durant 1 mois.
137 parts1 - 2 layers102 × 37 mm

- 2 layers85 × 56 mm

AT01
hshahzada/automated-tourniquet
2023/2024 Capstone Design Project for Biomedical Engineering
72 parts - 2 layers99.1 × 99.1 mm

Devboard io
mattis25/sierros_pcb
Circuit of Sierros Project (self-service device which does a resuscitation) OPEN HARDWARE
68 parts
Questions
How big is the Esp-32-board PCB?
It measures 53.4 × 68.6 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Esp-32-board use?
39 parts, built around the ESP32-WROOM-32, FT232RL, USBLC6-2SC6 and RF-YUS150TS-AE. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Esp-32-board KiCad files?
From the rafw87/hardware-modules repository on GitHub, at the commit this page was made from: the board is modules/esp-32-board/esp-32-board.kicad_pcb and its schematic modules/power-monitor-hat/power-monitor-hat.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Esp-32-board design in my own project?
Its repository publishes it under the CC-BY-SA-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).