
PSLab
fossasia/pslab-hardware
PSLab Hardware Design and Schematics https://pslab.io

Control 2 DPS5015 con pantalla Nextion y arduino nano
Dps rs232 is an open-source printed circuit board by radioelf, from the radioelf/DPS5015--Nextion repository on GitHub. It is a 2-layer board with 33 parts on 29 nets, routed with 138 tracks and 8 vias.
It is built around the 74HC126D and TX 1. Its parts include 9 resistors, 4 capacitors, 1 IC and 1 transistor. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Codes for the control of two DPS5015 sources through to nextion screen.
Codigos para el control de dos fuentes DPS5015 a través de una pantalla nextion.
https://www.youtube.com/watch?v=COuCyDTJvEc
Creative Commons License Disclaimer
UNLESS OTHERWISE MUTUALLY AGREED TO BY THE PARTIES IN WRITING, LICENSOR OFFERS THE WORK AS-IS AND MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND CONCERNING THE WORK, EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF TITLE, MERCHANTIBILITY, FITNESS FOR A PARTICULAR PURPOSE, NONINFRINGEMENT, OR THE ABSENCE OF LATENT OR OTHER DEFECTS, ACCURACY, OR THE PRESENCE OF ABSENCE OF ERRORS, WHETHER OR NOT DISCOVERABLE. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES, SO SUCH EXCLUSION MAY NOT APPLY TO YOU. EXCEPT TO THE EXTENT REQUIRED BY APPLICABLE LAW, IN NO EVENT WILL LICENSOR BE LIABLE TO YOU ON ANY LEGAL THEORY FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES ARISING OUT OF THIS LICENSE OR THE USE OF THE WORK, EVEN IF LICENSOR HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 10K | Resistor_SMD:R_0603_1608Metric | R1, R2, R3, R5, R6 |
| 3 | 10nF | Capacitor_SMD:C_0603_1608Metric | C1, C2, C3 |
| 3 | 330R | Resistor_SMD:R_0603_1608Metric | R4, R8, R9 |
| 2 | RX | TestPoint:TestPoint_THTPad_D2.0mm_Drill1.0mm | MK10, MK11 |
| 1 | +5v | TestPoint:TestPoint_THTPad_D2.0mm_Drill1.0mm | MK1 |
| 1 | 100nF | Capacitor_SMD:C_0603_1608Metric | C4 |
| 1 | 1K | Resistor_SMD:R_0603_1608Metric | R7 |
| 1 | 74HC126 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U1 |
| 1 | A | TestPoint:TestPoint_THTPad_D2.0mm_Drill1.0mm | MK3 |
| 1 | Arduino_Nano | Module:Arduino_Nano | A1 |
| 1 | B | TestPoint:TestPoint_THTPad_D2.0mm_Drill1.0mm | MK5 |
| 1 | Buzzer | Buzzer_Beeper:Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | C | TestPoint:TestPoint_THTPad_D2.0mm_Drill1.0mm | MK7 |
| 1 | GND | TestPoint:TestPoint_THTPad_D2.0mm_Drill1.0mm | MK2 |
| 1 | Led1 | TestPoint:TestPoint_THTPad_D2.0mm_Drill1.0mm | MK16 |
| 1 | Led2 | TestPoint:TestPoint_THTPad_D2.0mm_Drill1.0mm | MK15 |
| 1 | ON_3v3-5v | TestPoint:TestPoint_THTPad_D2.0mm_Drill1.0mm | MK14 |
| 1 | ON_OFF_encoder | TestPoint:TestPoint_THTPad_D2.0mm_Drill1.0mm | MK8 |
| 1 | Q_PNP | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | RX->nextion | TestPoint:TestPoint_THTPad_D2.0mm_Drill1.0mm | MK4 |
| 1 | TX1 | TestPoint:TestPoint_THTPad_D2.0mm_Drill1.0mm | MK12 |
| 1 | TX2 | TestPoint:TestPoint_THTPad_D2.0mm_Drill1.0mm | MK13 |
| 1 | TX<-nextion | TestPoint:TestPoint_THTPad_D2.0mm_Drill1.0mm | MK6 |
| 1 | USB_PC | TestPoint:TestPoint_THTPad_D2.0mm_Drill1.0mm | MK9 |
33 parts, built around the 74HC126D and TX 1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the radioelf/DPS5015--Nextion repository on GitHub, at the commit this page was made from: the board is hardware/dps_rs232.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask radioelf before reusing the design.

fossasia/pslab-hardware
PSLab Hardware Design and Schematics https://pslab.io



alexjx/avrdoper-re
AVR-Doper RE is a USB in-system programmer (ISP) for AVR microcontrollers. It is a respin of the original AVR-Doper, updated with an ATmega328P controller, a USB-C connector, selectable 5 V or 3.3 V target power, and a…



I-M-Robotics-Lab/STM32-Quadcopter
Quadcopter design based on STM32F411CEU Blackpill flight controller. Compatible with INAV 6.0 firmware.
