qcoral/bitski2tadaa
Bitski is an open-source printed circuit board by qcoral, from the qcoral/bitski repository on GitHub, published under the MIT licence. It is a 2-layer board of 83.1 × 34.1 mm with 26 parts on 129 nets.
It is built around the ESP32-S3-MINI-1-N8, BMP580 and GXHT40AD, with the USBLC6-2SC6 among its other parts. Its parts include 8 ICs, 7 capacitors, 5 resistors, 4 diodes and 1 connector. It belongs with the ESP32 boards of this library.
yup. it's the thing!
Inital sketch of what I am attempting to make:
Let's see how this works out
Feature list (planned):
| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 1uF | Capacitor_SMD:C_0402_1005Metric | C3, C5, C6 |
| 3 | LED_45deg | LED_SMD:LED_0402_1005Metric | D4, D5, D6 |
| 2 | 0pF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C7, C8 |
| 2 | 33 | Resistor_SMD:R_0402_1005Metric | R5, R6 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric | R2, R3 |
| 2 | IS31FL3731-QF | Package_DFN_QFN:QFN-28-1EP_4x4mm_P0.4mm_EP2.3x2.3mm | U7, U8 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R4 |
| 1 | 10uF | Capacitor_SMD:C_0402_1005Metric | C1 |
| 1 | BMP580 | Package_LGA:ST_HLGA-10_2x2mm_P0.5mm_LayoutBorder3x2y | U6 |
| 1 | BQ25185 | Package_DFN_QFN:Texas_DLH0010A_WSON-10-1EP_2.2x2mm_P0.4mm_EP0.9x1.5mm_ThermalVias | U2 |
| 1 | C_Small | Capacitor_SMD:C_0402_1005Metric | C2 |
| 1 | Conn_02x12_Odd_Even | Connector_USB:USB_C_Receptacle_HCTL_HC-TYPE-C-16P-01A | J1 |
| 1 | ESP32-S3-MINI-1-N8 | RF_Module:ESP32-S2-MINI-1 | U1 |
| 1 | GXHT40AD | Sensor_Humidity:Sensirion_DFN-4_1.5x1.5mm_P0.8mm_SHT4x_NoCentralPad | U5 |
| 1 | LED_45deg | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | D3 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U4 |
| 1 | XC6206PxxxMR | Package_TO_SOT_SMD:SOT-23-3 | U3 |
The 25 most common of 26 parts.
It measures 83.1 × 34.1 mm and has 2 copper layers, 1.6 mm thick.
26 parts, built around the ESP32-S3-MINI-1-N8, BMP580, GXHT40AD and USBLC6-2SC6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the qcoral/bitski repository on GitHub, at the commit this page was made from: the board is pcb/bitski.kicad_pcb and its schematic pcb/bitski.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
picafe/bicolor-matrix-v2
A 32x8 bicolor LED matrix module composed of 4 8x8 matrices based on the Holtek HT16K33A I2C LED driver. V1 paired it with a stacked adapter (RP2040 Zero + DS3231 module); V2 redesigns the matrix routing and puts an…
Michael-Manning/E-Paper-Climate-Logger
Firmware, PCB, and enclosure for the Weathergotchi E-Paper climate logger.
JamesTwallin/gas_sensor
A tiny plug-in board for the rev E phone-companion board. It stands upright in a notch in rev E's sensor end, between the two gas sensor cans, and pokes 4.5 mm out through a slot in the case face, so its tip sits in the…
burakbasdere/esp32-drone-fcu
Küçük, 1–2S LiPo beslemeli ve harici dört kanallı fırçasız ESC kullanan quadcopter için Rev A mühendislik prototipi. KiCad 9 projesini micro-fcu.kicadpro ile açın.
kiranj26/Posture-Tracker-Using-ESP32
Posture Correction using ESP32-MINI-1 and MU sensor (GY-521 / MPU-6050)
