
PSLab
fossasia/pslab-hardware
PSLab Hardware Design and Schematics https://pslab.io

KicadJE_AmpMultMix - INCOMPLETE
KicadJE AmpMultMix is an open-source printed circuit board by promesoft, from the promesoft/KicadJE_AmpMultMix repository on GitHub, published under the MIT licence. It is a 2-layer board of 100 × 100 mm with 28 parts on 25 nets.
It is built around the TL082. Its parts include 14 resistors, 9 connectors, 2 capacitors, 2 switches and 1 IC. It belongs with the audio and music boards of this library.
KicadJE_AmpMultMix - INCOMPLETE
NOTE - INITIALLY THE PROJECT "KiCadJE_LFO_1" will do the validation of the initial design of the MMX
| Stage | Detail | Status |
|---|---|---|
| create material | sch/pcb | |
| gerber | ||
| production | ||
| produced | ||
| delivered |
| Test | Detail | Status |
|---|---|---|
| Initial Inspection | ||
| Initial Technical Test | ||
| Initial Product Test | VCO CV from LFO | OK |
| Test | Detail | Status |
|---|---|---|
| Product Test | ||
| Product Test | ||
| Quality | ||
| Quality | ||
| Long Term Product Test | ||
| Power Draw |
| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 47k | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R201, R203, R204, R205, R206, R208, R210, R212 |
| 4 | 4k7 | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R207, R211, R213, R214 |
| 2 | 1u | Capacitor_SMD:C_1206_3216Metric_Pad1.42x1.75mm_HandSolder | C201, C202 |
| 2 | 20k | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R202, R209 |
| 2 | Inv/NonInv | AJ-Dropbox-Kicad:SP1MS1 | SW201, SW202 |
| 1 | HEADER_2x5_Doepfer | Connector_IDC:IDC-Header_2x05_P2.54mm_Vertical | P201 |
| 1 | In1.1 | AJ-Dropbox-Kicad:PJ301SM | J201 |
| 1 | In1.2 | AJ-Dropbox-Kicad:PJ301SM | J202 |
| 1 | In1.3 | AJ-Dropbox-Kicad:PJ301SM | J203 |
| 1 | In2 | AJ-Dropbox-Kicad:PJ301SM | J205 |
| 1 | Out1 | AJ-Dropbox-Kicad:PJ301SM | J204 |
| 1 | Out2.1 | AJ-Dropbox-Kicad:PJ301SM | J206 |
| 1 | Out2.2 | AJ-Dropbox-Kicad:PJ301SM | J207 |
| 1 | Out2.3 | AJ-Dropbox-Kicad:PJ301SM | J208 |
| 1 | TL082 | AJ-Dropbox-Kicad:AJ_SO-8_5.3x6.2mm_P1.27mm | U201 |

fossasia/pslab-hardware
PSLab Hardware Design and Schematics https://pslab.io

QuantumVillage/UncutGem
A prototype Full Stack fully Open Source NV Center Diamond Magnetometer

profdc9/DRSSTC-PCB-Pack
A pack of PCBs for a dual resonant solid state tesla coil setup. Pretty much everything you need.


tvlad1234/osillyscope
Low cost, low part count CH32V003-based oscilloscope


grappendorf/eurorack-spinfx
Spin FV-1 based effects module for Eurorack systems

telec16/modular-synth
Little side project, don't expect much updates.
It measures 100 × 100 mm and has 2 copper layers, 1.6 mm thick.
28 parts, built around the TL082. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the promesoft/KicadJE_AmpMultMix repository on GitHub, at the commit this page was made from: the board is KicadJE_AmpMultMix/KicadJE_AmpMultMix.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).