4 layers56 × 36 mm
QSIT PayloadADCboard
fhnw-ise-qcrypt/qsit_psd_payload_module_kicad
kicad drawings to interface a position sensitive detector (diode) for the QSIT payload
63 parts1
2 layers90 × 130 mm
Multimeter
PreferLinux/open-source-multimeter14Source repository for https://hackaday.io/project/10820-open-source-multimeter
- Size
- 90 × 130 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 194
- Nets
- 152
- Pads
- 600
- Tracks, vias
- 2,808, 155
- Pours
- 5
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 20 Apr 2016
- Updated
- 24 Aug 2016
Overview
Multimeter is an open-source printed circuit board by PreferLinux, from the PreferLinux/open-source-multimeter repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 90 × 130 mm with 194 parts on 152 nets, routed with 2,808 tracks and 155 vias.
It is built around the MCP6002-I/P, TSV634IPT and CT138, with the BD4835G-TR, MAX6070 and MCP73834 among its other parts. Its parts include 71 resistors, 39 capacitors, 25 ICs, 17 connectors and 15 diodes. It belongs with the sensors and measurement boards and the STM32 boards of this library.
Main components
7
MCP6002-I/P
PDIP-8-40℃~+85℃ 1.8V~6V 100uA 1MHz 1pA 1pA 2 23mA 28nV/√Hz@1kHz 2uV/℃ 4.5mV 600V/ms 76dB ESD protection Rail-to-Rail Input, Rail-to-Rail Output PDIP-8 Operational Amplifier ROHSMicrochip TechnologyOperational Amplifier
TSV634IPT
TSSOP-14-40℃~+125℃ 1.5V~5.5V 10pA 1pA 1uV/℃ 340V/ms 3mV 4 40mA 60nV/√Hz@1kHz 60uA 80dB 880kHz Rail-to-Rail Input, Rail-to-Rail Output TSSOP-14 Operational Amplifier ROHSSTMicroelectronicsOperational Amplifier
CT138
DIP-6Solid State Relays (MOS Output)COTO
BD4835G-TR
SSOP-5-40℃~+105℃@(Ta) 1 3.5V Active Low Open Drain Voltage Detector SSOP-5 Supervisor and Reset ICs ROHSROHM SemiconductorSupervisor And Reset ICs
MAX6070
UncategorisedMaxim Integrated (Analog Devices)MCP73834
UncategorisedMicrochip Technology
TPD2E001DZD
SOT-23-4-40℃~+85℃ 1.5pF 11V 1nA 2 5.5V ESD IEC 61000-4-2 Unidirectional SOT-23-4 ESD and Surge Protection (TVS/ESD) ROHSTexas InstrumentsESD And Surge Protection (TVS/ESD)
README
READMEThe schematics and PCB layout are done in KiCAD.
Please see https://hackaday.io/project/10820-open-source-multimeter for details. There are also details in the schematics.
Parts
194| Qty | Value | Footprint | References |
|---|---|---|---|
| 22 | 1M | my footprints:SMDuniversal_0603to1210_HandSoldering | R217, R218, R220, R221, R222, R223, R226, R227, R229, R230, R234, R236, R239, R240, R241, R242 +6 |
| 13 | 74LVC1G66 GNDA | TO_SOT_Packages_SMD:SOT-353 | U204, U206, U208, U209, U210, U211, U212, U213, U214, U215, U216, U217, U218 |
| 13 | R | my footprints:SMDuniversal_0603to1210_HandSoldering | R213, R214, R219, R224, R225, R231, R232, R233, R235, R237, R238, R504, R505 |
| 11 | 0.1u | my footprints:SMDuniversal_0603to0805_HandSoldering | C108, C110, C117, C201, C202, C205, C303, C305, C307, C310, C501 |
| 9 | 10u | my footprints:SMDuniversal_0603to1206_HandSoldering | C109, C120, C121, C204, C206, C304, C306, C502, C503 |
| 8 | 1k | my footprints:SMDuniversal_0603to1210_HandSoldering | R203, R211, R401, R402, R403, R404, R405, R508 |
| 7 | 1u | my footprints:SMDuniversal_0603to0805_HandSoldering | C106, C107, C116, C119, C301, C302, C309 |
| 6 | 100k | my footprints:SMDuniversal_0603to1210_HandSoldering | R104, R105, R212, R228, R301, R507 |
| 6 | 500R | my footprints:SMDuniversal_0603to1210_HandSoldering | R101, R102, R103, R106, R107, R108 |
| 6 | D_Schottky | my footprints:SC-90A | D205, D206, D213, D214, D302, D303 |
| 5 | 0.01u | my footprints:SMDuniversal_0603to0805_HandSoldering | C111, C112, C113, C118, C308 |
| 5 | CONN_01X01 | Wire_Pads:SolderWirePad_single_SMD_5x10mm | P401, P402, P403, P404, P405 |
| 4 | 1.8k | Resistors_Universal:Resistor_SMDuniversal_0805to2512_HandSoldering | R205, R206, R207, R208 |
| 4 | 10k | my footprints:SMDuniversal_0603to1210_HandSoldering | R209, R210, R216, R506 |
| 4 | D | my footprints:Diode_R-6_Horizontal_RM15 | D201, D202, D203, D204 |
| 4 | Q_NMOS_GSD | TO_SOT_Packages_SMD:SOT-23 | Q102, Q201, Q302, Q501 |
| 4 | TVS | Diodes_SMD:SMB_Handsoldering | D207, D208, D209, D210 |
| 4 | VR | Varistors:RV_Disc_D15.5_W5.4_P7.5 | VR201, VR202, VR203, VR204 |
| 3 | 3.9n | my footprints:SMDuniversal_0603to0805_HandSoldering | C103, C104, C105 |
| 3 | 68R | my footprints:SMDuniversal_0603to1210_HandSoldering | R247, R248, R249 |
| 3 | Mounting hole | Mounting_Holes:MountingHole_3.2mm_M3 | P103, P104, P105 |
| 3 | Q_PMOS_GSD | TO_SOT_Packages_SMD:SOT-23 | Q101, Q301, Q502 |
| 2 | 10n | my footprints:SMDuniversal_0603to0805_HandSoldering | C114, C115 |
| 2 | 18p | my footprints:SMDuniversal_0603to0805_HandSoldering | C101, C102 |
| 2 | 500mA | Resistors_SMD:R_1210_HandSoldering | F501, F502 |
| 2 | CONN_01X05 | Pin_Headers:Pin_Header_Straight_1x05 | P406, P407 |
| 2 | CT138 | Housings_DIP:DIP-6_W7.62mm_LongPads | U201, U205 |
| 2 | FILTER | my footprints:SMDuniversal_0603to1210_HandSoldering | FB301, FB501 |
| 2 | FUSE | my footprints:Fuseholder6x32_horiz_open_inline_Type-I | F201, F202 |
| 2 | Jumper_NC_Small | Resistors_SMD:R_0603_HandSoldering | JP202, JP204 |
| 2 | Jumper_NO_Small | Resistors_SMD:R_0603_HandSoldering | JP201, JP203 |
| 1 | 10 A | Connect:Banana_Jack_1Pin | P201 |
| 1 | 100R | my footprints:SMDuniversal_0603to1210_HandSoldering | R204 |
| 1 | 100k | Resistors_ThroughHole:Resistor_Horizontal_RM20mm | R215 |
| 1 | 100m | Resistors_Universal:Resistor_SMD+THTuniversal_0805to2512_RM10_HandSoldering | R202 |
| 1 | 10m | Resistors_Universal:Resistor_SMD+THTuniversal_0805to2512_RM10_HandSoldering | R201 |
| 1 | 2.5k | my footprints:SMDuniversal_0603to1210_HandSoldering | R503 |
| 1 | 3.6V | TO_SOT_Packages_SMD:SOT-23 | D301 |
| 1 | 8 MHz | Crystals:Crystal_HC49-SD_SMD | Y101 |
| 1 | BD4835 | my footprints:VSOF5_HandSoldering | U103 |
| 1 | BOOT0 | my footprints:Pin_Header_Straight_1x02 | JP101 |
| 1 | COMMON | my footprints:Banana_Jack_1Pin_2Contact_SM_Top | P204 |
| 1 | Expansion header | Pin_Headers:Pin_Header_Straight_2x07 | P101 |
| 1 | ILI9341_LCD_Breakout | my footprints:ILI9341_LCD_Breakout | U102 |
| 1 | Li-Ion_Cell | Pin_Headers:Pin_Header_Straight_1x03 | BT501 |
| 1 | MAX6070 | TO_SOT_Packages_SMD:SOT-23-6_Handsoldering | U302 |
| 1 | MCP6002 | my footprints:MSOP-8_3x3mm_Pitch0.65mm | U202 |
| 1 | MCP6N11 | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | U203 |
| 1 | MCP73834 | my footprints:MSOP-10_3x3mm_Pitch0.5mm | U502 |
| 1 | NCV551SN33T1G | TO_SOT_Packages_SMD:SOT-23-5 | U301 |
| 1 | Net_Tie | my footprints:Net_Tie | JP302 |
| 1 | Programming header | Pin_Headers:Pin_Header_Straight_1x06 | P102 |
| 1 | SPEAKER | Pin_Headers:Pin_Header_Straight_1x02 | SP101 |
| 1 | STM32F373R8Tx | Housings_QFP:LQFP-64_10x10mm_Pitch0.5mm | U101 |
| 1 | SW_PUSH | Buttons_Switches_ThroughHole:SW_PUSH_SMALL | SW401 |
| 1 | TPD2E001 | my footprints:VSOF5_HandSoldering | U501 |
| 1 | TSV634 | my footprints:TSSOP-14_4.4x5mm_Pitch0.65mm | U207 |
| 1 | USB_OTG | my footprints:MicroUSB_B_Vertical | P501 |
| 1 | V R | my footprints:Banana_Jack_1Pin_2Contact_SM_Top | P203 |
| 1 | mA | Connect:Banana_Jack_1Pin | P202 |
Questions
How big is the Multimeter PCB?
It measures 90 × 130 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Multimeter use?
194 parts, built around the MCP6002-I/P, TSV634IPT, CT138 and BD4835G-TR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Multimeter KiCad files?
From the PreferLinux/open-source-multimeter repository on GitHub, at the commit this page was made from: the board is Electrical design/Multimeter.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Multimeter design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
Similar boards
- 2 layers33.5 × 34.3 mm
FullChargeAhead
AlanFord/FullChargeAhead
Full Charge Ahead pcb for the Contextual Electronics course
23 parts - 4 layers88 × 58 mm
BIOCHEST ECG EMG
8aChristian/BIOCHEST-ECG-EMG
Figure 1: Full 4-Layer High-Density Medical PCBA with Galvanic Isolation Barrier & Routed Copper Tracks.
29 parts - 4 layers57 × 27 mm
Altlog
alexdortiz/flight-data-recorder
4-layer flight data recorder. Open altlog.kicadpro in KiCad 10.
47 partsMIT - 4 layers62 × 105 mm
PT100 Datalogger
rasusmilch/PT100_Mesh_Datalogger
This application turns an ESP32-S3 N8R2 into a UTC-centric PT100 data logger with FRAM-first buffering, SD-card CSV batching/verification, DS3231 RTC support, mesh streaming, and serial-console calibration.
139 parts - 2 layers103.4 × 73 mm
Power supply
vt-amplab/basic-soldering-cert-board
Kicad files for the new basic soldering certification board
104 partsApache-2.0 - 2 layers89 × 49.9 mm
- 2 layers100 × 80 mm
Phase3-manager
udaravima/Lab_Bench
A modular, rack-style DC power supply: up to 8 hot-pluggable 600 W buck modules on a shared DC input bus, coordinated by a central manager over CAN.
87 parts1GPL-3.0