

Panelised
Schematics and PCB's designed with Kicad
- Size
- 114.1 × 100.2 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 252
- Nets
- 124
- Pads
- 750
- Tracks, vias
- 1,525, 220
- Pours
- 7
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 17 Jun 2026
- Updated
- 17 Jun 2026
Overview
Panelised is an open-source printed circuit board by pnn69, from the pnn69/Kicad_PCB repository on GitHub. It is a 4-layer board of 114.1 × 100.2 mm with 252 parts on 124 nets, routed with 1,525 tracks and 220 vias.
It is built around the SN74LV1T34DBV, LMR16020PDDA and LM1117DT-3.3, with the USBLC6-4SC6, CRGH0603F10K and AO3401A among its other parts. Its parts include 76 capacitors, 67 resistors, 26 transistors, 24 diodes and 15 connectors. It belongs with the ESP32 boards of this library.
Main components
11SN74LV1T34DBV
SOT-23-5-40℃~+125℃ 1 1 1.6V~5.5V 10uA 5.5ns@5V,15pF 74LV 8mA 8mA Level shifting Push-pull Unidirectional SOT-23-5 Buffers, Drivers, Receivers, Transceivers ROHSTexas InstrumentsBuffers, Drivers, Receivers, TransceiversLMR16020PDDA
SOIC-8-EP-40℃~+125℃@(TJ) 1 2.5MHz 2A 4.3V~60V 40uA 800mV~50V Adjustable Buck Buck Built-in No SOIC-8-EP DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersLM1117DT-3.3
TO-2520℃~+125℃@(Tj) 1 1.2V@(800mA) 15V 3.3V 5mA 75dB@(120Hz) 800mA Fixed Over Current Protection、Over Temperature Protection、Short Circuit Protection Positive TO-252 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsUSBLC6-4SC6
SOT-23-6-55℃~+125℃ 0.3pF 15V 300W@8/20us 4.7A@8/20us 5V 6V 80nA ESD Four channels IEC 61000-4-2、IEC 61000-4-5、IEC 61000-4-4 Unidirectional SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSTECH PUBLICESD And Surge Protection (TVS/ESD)CRGH0603F10K
0603-55℃~+155℃ 10kΩ 200mW 50V Thick Film Resistor ±1% ±100ppm/℃ 0603 Chip Resistor - Surface Mount ROHSTE ConnectivityChip Resistor - Surface MountAO3401A
SOT-231 P-Channel 14nC@10V 30V 47mΩ@10V、60mΩ@4.5V、85mΩ@2.5V 4A 55pF 645pF 80pF 900mV SOT-23 MOSFETs ROHSAlpha & Omega SemiconductorMOSFETs1N4148WS
SOD-3231.25V@150mA 100V 150mA 1uA@75V 200mW 2A 4ns Independent SOD-323 Switching Diodes ROHSJiangsu Changjing Electronics Technology (CJ)Switching DiodesAO3400A
SOT-23-55℃~+150℃ 1 N-channel 1.45V 1.4W 30V 48mΩ@2.5V 5.7A 50pF 630pF 75pF 7nC@10V N-Channel SOT-23 MOSFETs ROHSAlpha & Omega SemiconductorMOSFETsWS2812B
5mm X 5mm Surface Mount RGB LED with Intelligent ControlWorldsemiUncategorisedMMBT3904
SOT-23-55℃~+150℃ 1 NPN 100 100nA 200mA 200mW 300MHz 300mV 40V 6V NPN SOT-23 Bipolar (BJT) ROHSJiangsu Changjing Electronics Technology (CJ)Bipolar (BJT)SS54
SMA(DO-214AC)-55℃~+125℃ 1mA@40V 40V 550mV@5A 5A Independent SMA(DO-214AC) Schottky Diodes ROHSMDDSchottky Diodes
Parts
252| Qty | Value | Footprint | References |
|---|---|---|---|
| 37 | 100n | A_Device:C_0603 | C101, C101, C102, C102, C103, C104, C104, C105, C106, C106, C107, C107, C108, C108, C108, C109 +21 |
| 21 | 10K | A_Device:R_0603 | R101, R101, R102, R103, R103, R105, R107, R109, R109, R110, R110, R111, R111, R119, R120, R123 +5 |
| 15 | 100u/10V | Capacitor_SMD:C_1210_3225Metric | C102, C103, C105, C106, C111, C114, C117, C117, C119, C207, C212, C216, C217, C301, C302 |
| 15 | AO3401A | Package_TO_SOT_SMD:SOT-23 | Q102, Q105, Q106, Q107, Q108, Q109, Q110, Q111, Q112, Q113, Q114, Q115, Q116, Q119, Q204 |
| 12 | 100K | A_Device:R_0603 | R102, R104, R105, R106, R106, R117, R118, R126, R201, R202, R203, R213 |
| 11 | 100 | A_Device:R_0603 | R101, R102, R104, R105, R106, R107, R108, R108, R111, R112, R210 |
| 7 | 1N4148WS | A_Device:D_SOD-323_1.8x1.4x1.15 | D101, D101, D104, D104, D109, D109, D202 |
| 7 | AO3400A | Package_TO_SOT_SMD:SOT-23 | Q101, Q101, Q101, Q102, Q103, Q104, Q203 |
| 6 | 22uF/35V | A_Device:C_1206_(1.6) | C107, C110, C115, C201, C202, C203 |
| 6 | 47K | A_Device:R_0603 | R107, R115, R124, R204, R206, R214 |
| 6 | WS2812B | LED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D101, D102, D102, D103, D103, D104 |
| 5 | 10n | A_Device:C_0603 | C103, C112, C115, C122, C206 |
| 5 | 1k | A_Device:R_0603 | R108, R110, R125, R216, R218 |
| 5 | 1n | A_Device:C_0603 | C119, C123, C124, C125, C215 |
| 4 | 10u/25V | A_Device:C_0805 | C104, C105, C210, C211 |
| 4 | MMBT3904 | Package_TO_SOT_SMD:SOT-23 | Q102, Q117, Q117, Q201 |
| 4 | MountingHole | A_Mechanical:NPTH_M3 | H401, H402, H403, H404 |
| 2 | 0.75V | A_Pads_Pins:Testpad_1.4 | TP106, TP203 |
| 2 | 10uH | A_Device:L_6.6x7.0mm | L101, L201 |
| 2 | 18K | A_Device:R_0603 | R121, R122 |
| 2 | 2.2k | A_Device:R_0603 | R103, R104 |
| 2 | 2K | A_Device:R_0603 | R129, R129 |
| 2 | 3.3V | A_Passive:LED_0805 | D108, D205 |
| 2 | 4.7k | A_Device:R_0603 | R113, R114 |
| 2 | 4.7uF/10V | A_Device:C_1206_(1.6) | C113, C221 |
| 2 | 4.7uF/50V | A_Device:C_1206_(1.6) | C101, C204 |
| 2 | 6.2k | A_Device:R_0603 | R109, R217 |
| 2 | 8.2K | A_Device:R_0603 | R116, R215 |
| 2 | ACCU2 | A_Connector:AMASS_XT60IPW-M_1x03_P7.20mm_Horizontal | J104, J107 |
| 2 | Buzzer | A_Misc:Buzzer-12x6.5x5.2 | BZ101, BZ101 |
| 2 | ESC_BB | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J103, J103 |
| 2 | ESP32-WROOM-32E_(visible_peripherals) | A_Module:ESP32-WROOM-32 | U101, U101 |
| 2 | GND | TestPoint:TestPoint_Loop_D2.54mm_Drill1.5mm_Beaded | TP101, TP205 |
| 2 | LM1117DT-3.3 | Package_TO_SOT_SMD:TO-252-3_TabPin2 | U104, U201 |
| 2 | LMR16020PDDA | Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.81mm_ThermalVias | U101, U202 |
| 2 | On/Off | A_Connector:Header_1x03_P2.54_Male | SW101, SW201 |
| 2 | PWR_EN | A_Pads_Pins:Testpad_1.4 | TP102, TP201 |
| 2 | PWR_ESC | LED_SMD:LED_0603_1608Metric | D105, D106 |
| 2 | Prog | Connector_IDC:IDC-Header_2x03_P2.54mm_Vertical | J101, J101 |
| 2 | RX | A_Passive:LED_0805 | D105, D105 |
| 2 | SN74LV1T34DBV | Package_TO_SOT_SMD:SOT-23-5 | U102, U103 |
| 2 | SS54 | Diode_SMD:D_SMA | D107, D204 |
| 2 | TX | A_Passive:LED_0805 | D108, D108 |
| 2 | USBLC6-4SC6 | Package_TO_SOT_SMD:SOT-23-6 | U103, U105 |
| 2 | Vbatt | A_Pads_Pins:Testpad_1.4 | TP109, TP202 |
| 2 | ~{RESET} | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | SW101, SW102 |
| 1 | 0.3E 240E@100MHz | A_Device:L_0805_(1.2) | FB101 |
| 1 | Ai-Thinker-Ra-02 | A_Module:Ai-Thinker-Ra-02-LoRa | U301 |
| 1 | BUZZER | A_Pads_Pins:Testpad_1 | TP101 |
| 1 | CHRG/DATA | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J201 |
| 1 | CHRG/DATA | A_Connector:AMASS_XT60IPW-M_1x03_P5.50mm_Vertical | J101 |
| 1 | COM | LED_SMD:LED_0603_1608Metric | D103 |
| 1 | COM | A_Pads_Pins:Testpad_1.4 | TP204 |
| 1 | Conn_01x06_Socket | Connector_JST:JST_XH_B6B-XH-A_1x06_P2.50mm_Vertical | J102 |
| 1 | ESC_5V | A_Pads_Pins:Testpad_1 | TP107 |
| 1 | ESC_5V | A_Pads_Pins:Testpad_1.4 | TP108 |
| 1 | ESC_PWM | A_Pads_Pins:Testpad_1.4 | TP105 |
| 1 | ESC_PWM | A_Pads_Pins:Testpad_1 | TP104 |
| 1 | ESC_PWR_BB | A_Connector:AMASS_XT60PW-F_1x02_P7.20mm_Horizontal | J106 |
| 1 | ESC_PWR_SB | A_Connector:AMASS_XT60PW-F_1x02_P7.20mm_Horizontal | J105 |
| 1 | ESC_SB | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J102 |
| 1 | GPS | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J103 |
| 1 | LEDS | A_Pads_Pins:Testpad_1 | TP101 |
| 1 | LSM303AGRTR | Package_LGA:LGA-12_2x2mm_P0.5mm | U102 |
| 1 | MODE | Button_Switch_SMD:SW_SPST_TL3342 | SW102 |
| 1 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H101 |
| 1 | TO CPU | Connector_IDC:IDC-Header_2x05_P2.54mm_Vertical | J108 |
| 1 | TO PSU | Connector_IDC:IDC-Header_2x05_P2.54mm_Vertical | J108 |
| 1 | Vcell | A_Pads_Pins:Testpad_1 | TP103 |
| 1 | ~{BOOT}/MODE | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | SW101 |
More from pnn69/Kicad_PCB
12- 4 layers100 × 80 mm

- 4 layers103 × 36 mm

- 4 layers80 × 104.1 mm

- 4 layers120 × 48 mm

- 4 layers58.7 × 42 mm

- 4 layers76 × 68 mm

- 4 layers65 × 69 mm

- 4 layers65 × 69 mm

- 4 layers80 × 46 mm

- 4 layers52.5 × 56 mm

- 4 layers66 × 52 mm

- 4 layers50 × 42 mm

Similar boards
- 4 layers194 × 40 mm

- 4 layers74.9 × 58.5 mm

- 4 layers81 × 143.2 mm

- 4 layers99 × 60 mm

Grip strength meter
houseofbigseals/grip_strength_meter_pcb
schematic and pcb for custom esp32 grip strength meter project
123 parts - 4 layers140 × 100 mm

Dc usv
TobleMiner/DC-UPS
A small DC UPS, designed to keep small appliances like consumer network equipment running during power outages
351 parts223CERN-OHL-P-2.0 - 4 layers86.6 × 85.1 mm

- 4 layers120 × 120 mm

- 4 layers144 × 127 mm

Frothfet
hoeken/frothfet
Yarrboard load controller board with current sense, volt sense, fuses, and sender support.
394 parts14GPL-3.0
Questions
How big is the Panelised PCB?
It measures 114.1 × 100.2 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Panelised use?
252 parts, built around the SN74LV1T34DBV, LMR16020PDDA, LM1117DT-3.3 and USBLC6-4SC6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Panelised KiCad files?
From the pnn69/Kicad_PCB repository on GitHub, at the commit this page was made from: the board is panelised/untitled.kicad_pcb and its schematic Nice-Buoy-V1_0/Accumonitor.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Panelised design in my own project?
Its repository states no licence, so its author keeps all rights: ask pnn69 before reusing the design.