
LMR16020PDDA
Texas InstrumentsExtended
-40℃~+125℃@(TJ) 1 2.5MHz 2A 4.3V~60V 40uA 800mV~50V Adjustable Buck Buck Built-in No SOIC-8-EP DC-DC Converters ROHS
- Part id
- ti/LMR16020PDDA
- Category
- DC DC Converters
- Package
- SOIC-8-EP
- Pins
- 9
- In stock
- 15,567 at JLCPCB (C190006)
- Used on
- 8 open-source boards
Overview
The LMR16020PDDA is a DC DC Converter made by Texas Instruments in a SOIC-8-EP package with 9 pins. -40℃~+125℃@(TJ) 1 2.5MHz 2A 4.3V~60V 40uA 800mV~50V Adjustable Buck Buck Built-in No SOIC-8-EP DC-DC Converters ROHS.
PCBKit's library has its KiCad symbol (Celestial_Power_Switchmode:TI LMR16020PDDAR, from Altium's library) and its footprint (Celestial_Leaded_SOIC:TI SOIC-8 DDA0008B, from Altium's library), ready for a KiCad board. 15,567 are in stock at JLCPCB (part C190006). 8 open-source boards in 5 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
13- Supply, least
- 4.3 V · VIN, recommended operating min · p. 4
- Supply, most
- 60 V · VIN, recommended operating max · p. 4
- Supply, absolute maximum
- 65 V · VIN, absolute maximum · p. 4
- Junction, hottest
- 150 °C · Junction temperature, absolute maximum · p. 4
- Takes asleep
- 1 µA · Shutdown supply current, typical, VEN = 0 V · p. 5
- Takes asleep
- 40 µA · Sleep-mode input quiescent current, typical · p. 12
- Gives
- 2 A · Continuous output current · p. 1
- Current limit
- 3.15 A · High-side current limit, typical, VIN = 12 V, TA = 25 °C, open loop · p. 6
- Feedback reference
- 750 mV · FB feedback voltage, typical, TJ = 25 °C · p. 5
- Switches at
- 1.912 MHz · Switching frequency, typical, RT = 11.5 kΩ · p. 7
- Junction to air (DDA (HSOIC))
- 42.5 K/W · Junction-to-ambient thermal resistance · p. 5
- Junction to board (DDA (HSOIC))
- 25.5 K/W · Junction-to-board thermal resistance · p. 5
- Junction to case (DDA (HSOIC))
- 56.1 K/W · Junction-to-case (top) thermal resistance · p. 5
What it is and has
7- Control
- Current mode · p. 1
- Frequency synchronization
- External clock · p. 1
- Compensation
- Internal · p. 1
- Enable
- Precision enable input · p. 1
- Power good
- Power-good flag · p. 1
- Protection
- Thermal, overvoltage and short protection · p. 1
- Package
- 8-pin HSOIC with PowerPAD · p. 1
Around it
14- cap 0.1 μF
- between BOOT and SW; High quality bootstrap capacitor for high-side MOSFET driver. · p. 3
- res 10 kΩ to 100 kΩ
- between PGOOD and logic rail; Power-good pull-up; rail or other DC voltage must be no higher than 7 V. · p. 3
- res 10 kΩ to 100 kΩ
- between FB and GND; Recommended RFBB range; divider resistors should have 1% tolerance or better and temperature coefficient of 100 ppm or less. · p. 13
- res 10 kΩ to 100 kΩ
- between PGOOD and pull-up supply; Typical pull-up range; the voltage at PGOOD must not exceed 7 V. · p. 16
- res 100 kΩ
- between VOUT and FB; RFBT, upper feedback resistor in the 5 V output example. · p. 20
- res 17.8 kΩ
- between FB and GND; RFBB, lower feedback resistor in the 5 V output example. · p. 20
- res 41.2 kΩ
- between RT/SYNC and GND; Standard resistor value for the 600 KHz switching-frequency example. · p. 20
- ind 10 μH
- between SW and VOUT; Ferrite inductor for the design example, with 2 A RMS and 4 A saturation current capability. · p. 20
- cap 2 × 33 μF
- between VOUT and GND; Parallel 16 V X7R ceramic output capacitors, with 5 mΩ ESR, for the design example. · p. 21
- diode 2 A
- between GND and SW; Schottky catch diode; 2 A is a starting point. Breakdown rating is preferably 25% above maximum input voltage. · p. 21
- cap 4.7 μF to 10 μF
- between VIN and GND; Recommended high-frequency input decoupling range; X5R or X7R ceramic with sufficient voltage rating. · p. 21
- cap 2 × 2.2 μF
- between VIN and GND; 100 V X7R ceramic input capacitors for the design example. · p. 21
- cap 0.1 μF
- between VIN and GND; High-frequency filtering capacitor; place as close as possible to the device pins. · p. 21
- cap 0.1 μF
- between SW and BOOT; Required bootstrap capacitor, rated 16 V or higher, with X7R or X5R ceramic dielectric. · p. 21
Specifications
59| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Input Voltages | VIN, EN to GND | min -0.3 · max 65 V | 4 |
| Input Voltages | BOOT to GND | min -0.3 · max 71 V | 4 |
| Input Voltages | FB to GND | min -0.3 · max 7 V | 4 |
| Input Voltages | RT/SYNC to GND | min -0.3 · max 3.6 V | 4 |
| Input Voltages | PGOOD to GND | min -0.3 · max 7 V | 4 |
| Output Voltages | BOOT to SW | max 6.5 V | 4 |
| Output Voltages | SW to GND | min -3 · max 65 V | 4 |
| Junction temperature TJ | min -40 · max 150 °C | 4 | |
| Storage temperature Tstg | min -65 · max 150 °C | 4 | |
| Electrostatic discharge V(ESD) | Human-body model (HBM), ± rating | max 2000 V | 4 |
| Electrostatic discharge V(ESD) | Charged-device model (CDM), ± rating | max 500 V | 4 |
| Buck Regulator | VIN | min 4.3 · max 60 V | 4 |
| Buck Regulator | VOUT | min 0.8 · max 50 V | 4 |
| Buck Regulator | BOOT | max 66 V | 4 |
| Buck Regulator | SW | min -1 · max 60 V | 4 |
| Buck Regulator | FB | min 0 · max 5 V | 4 |
| Control | EN | min 0 · max 60 V | 4 |
| Control | RT/SYNC | min 0 · max 3.3 V | 4 |
| Control | PGOOD to GND | min 0 · max 5 V | 4 |
| Switching frequency range at RT mode | min 200 · max 2500 kHz | 4 | |
| Switching frequency range at SYNC mode | min 250 · max 2300 kHz | 4 | |
| Operating junction temperature, TJ | min -40 · max 125 °C | 4 | |
| Junction-to-ambient thermal resistance RθJA | DDA (HSOIC), 8 pins | typ 42.5 °C/W | 5 |
| Junction-to-top characterization parameter ψJT | DDA (HSOIC), 8 pins | typ 9.9 °C/W | 5 |
| Junction-to-board characterization parameter ψJB | DDA (HSOIC), 8 pins | typ 25.4 °C/W | 5 |
| Junction-to-case (top) thermal resistance RθJC(top) | DDA (HSOIC), 8 pins | typ 56.1 °C/W | 5 |
| Junction-to-case (bottom) thermal resistance RθJC(bot) | DDA (HSOIC), 8 pins | typ 3.8 °C/W | 5 |
| Junction-to-board thermal resistance RθJB | DDA (HSOIC), 8 pins | typ 25.5 °C/W | 5 |
| Operation input voltage VIN | min 4.3 · max 60 V | 5 | |
| Under voltage lockout thresholds UVLO | Rising threshold | min 3.8 · typ 4 · max 4.2 V | 5 |
| Under voltage lockout thresholds UVLO | Hysteresis | typ 285 mV | 5 |
| Shutdown supply current ISHDN | VEN = 0 V, TA = 25 °C, 4.3 V ≤ VIN ≤ 60 V | typ 1 · max 3 uA | 5 |
| Operating quiescent current (non-switching) IQ | VFB = 1.0 V, TA = 25 °C | typ 40 uA | 5 |
| EN Threshold Voltage VEN_TH | min 1.05 · typ 1.2 · max 1.38 V | 5 | |
| EN PIN current IEN_PIN | Enable threshold +50 mV | typ -4.6 uA | 5 |
| EN PIN current IEN_PIN | Enable threshold -50 mV | typ -1 uA | 5 |
| EN hysteresis current IEN_HYS | typ -3.6 uA | 5 | |
| Internal soft-start time tSS | 10% to 90% of FB voltage | typ 4 ms | 5 |
| Power-good flag under voltage tripping threshold VPG_UV | POWER GOOD (% of FB voltage) | typ 94 % | 5 |
| Power-good flag under voltage tripping threshold VPG_UV | POWER BAD (% of FB voltage) | typ 92 % | 5 |
| Power-good flag over voltage tripping threshold VPG_OV | POWER BAD (% of FB voltage) | typ 109 % | 5 |
| Power-good flag over voltage tripping threshold VPG_OV | POWER GOOD (% of FB voltage) | typ 107 % | 5 |
| Power-good flag recovery hysteresis VPG_HYS | % of FB voltage | typ 2 % | 5 |
| PGOOD leakage current at high level output IPG | VPull-Up = 5 V | typ 10 · max 200 nA | 5 |
| PGOOD low level output voltage VPG_LOW | IPull-Up = 1 mA | typ 0.1 V | 5 |
| Minimum VIN for valid PGOOD output VIN_PG_MIN | VPull-Up < 5 V at IPull-Up = 100 uA | typ 1.6 · max 1.95 V | 5 |
| Feedback voltage VFB | TJ = 25 °C | min 0.746 · typ 0.75 · max 0.754 V | 5 |
| Feedback voltage VFB | TJ = -40 °C to 125 °C | min 0.735 · typ 0.75 · max 0.765 V | 5 |
| On-resistance RDS_ON | VIN = 12 V, BOOT to SW = 5.8 V | typ 155 · max 320 mΩ | 6 |
| Current limit ILIMT | VIN = 12 V, TA = 25 °C, Open Loop | min 2.5 · typ 3.15 · max 3.8 A | 6 |
| Thermal shutdown threshold TSHDN | typ 170 °C | 6 | |
| Hysteresis THYS | typ 12 °C | 6 | |
| Switching frequency fSW | RT = 11.5 kΩ | min 1758 · typ 1912 · max 2066 kHz | 7 |
| SYNC clock high level threshold VSYNC_HI | min 1.7 V | 7 | |
| SYNC clock low level threshold VSYNC_LO | max 0.5 V | 7 | |
| Minimum SYNC input pulse width TSYNC_MIN | Measured at 500 kHz, VSYNC_HI > 3 V, VSYNC_LO < 0.3 V | typ 30 ns | 7 |
| PLL lock in time TLOCK_IN | Measured at 500 kHz | typ 100 us | 7 |
| Minimum controllable on time TON_MIN | VIN = 12 V, BOOT to SW = 5.8 V, ILoad = 1A | typ 90 ns | 7 |
| Maximum duty cycle DMAX | fSW = 200 kHz | typ 97 % | 7 |
Pins, by the datasheet
9- 1 BOOT
- Bootstrap connection for high-side MOSFET driver; connect a high quality 0.1 uF capacitor to SW. · p. 3
- 2 VIN
- Connect to power supply and bypass capacitors CIN; keep the VIN, high frequency bypass CIN and GND path as short as possible. · p. 3
- 3 EN
- Enable with internal pull-up; pull below 1.2 V to disable, float or connect to VIN to enable; two resistors adjust input undervoltage lockout. · p. 3
- 4 RT/SYNC
- Connect a resistor to ground to set switching frequency, or apply an external clock for synchronization; returns to resistor programming when clock edges stop. · p. 3
- 5 FB
- Feedback input; connect to the feedback divider to set VOUT; do not short to ground during operation. · p. 3
- 6 PGOOD
- Power-good flag; use a 10 kΩ to 100 kΩ pull-up resistor to a logic rail or other DC voltage no higher than 7 V. · p. 3
- 7 GND
- System ground pin. · p. 3
- 8 SW
- Switching output connected internally to high-side power MOSFET; connect to power inductor. · p. 3
- 9 Thermal Pad
- Major die heat dissipation path; must connect to PCB ground plane. · p. 3
Ordering codes, by the datasheet
6- LMR16020PDDAR
- HSOIC (8) · 4.89 mm x 3.90 mm nominal body size · p. 1
- LMR16020PDDA
- SO PowerPAD (DDA), 8 pins · 75 per tube; NIPDAU or NIPDAUAG lead finish; -40 to 125 °C operating temperature. · p. 28
- LMR16020PDDA.B
- SO PowerPAD (DDA), 8 pins · 75 per tube; NIPDAU lead finish; -40 to 125 °C operating temperature. · p. 28
- LMR16020PDDAR.B
- SO PowerPAD (DDA), 8 pins · 2500 per large tape and reel; NIPDAU lead finish; -40 to 125 °C operating temperature. · p. 28
- LMR16020PDDARG4
- SO PowerPAD (DDA), 8 pins · 2500 per large tape and reel; NIPDAU lead finish; -40 to 125 °C operating temperature. · p. 28
- LMR16020PDDARG4.B
- SO PowerPAD (DDA), 8 pins · 2500 per large tape and reel; NIPDAU lead finish; -40 to 125 °C operating temperature. · p. 28
Open-source boards using it
8- 4 layers74.9 × 58.5 mm

- 2 layers87 × 115 mm

- 4 layers114.1 × 100.2 mm

- 4 layers194 × 40 mm

- 4 layers90 × 90 mm

- 4 layers52.5 × 56 mm

- 4 layers103 × 36 mm

- 4 layers80 × 46 mm

Questions
Is there a KiCad symbol and footprint for the LMR16020PDDA?
Yes. The symbol is Celestial_Power_Switchmode:TI LMR16020PDDAR and the footprint Celestial_Leaded_SOIC:TI SOIC-8 DDA0008B, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the LMR16020PDDA?
SOIC-8-EP, with 9 pins. Its footprint is drawn on this page.
Where is the LMR16020PDDA datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the LMR16020PDDA?
JLCPCB lists it as part C190006, with 15,567 in stock; the sellers' links on this page open their listings.
Which open-source boards use the LMR16020PDDA?
8 boards in 5 repositories on GitHub; the most starred are listed on this page, with their KiCad files.