

NoPour
In situ Plankton Assemblage eXplorer
- Size
- 45.7 × 66 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 68
- Nets
- 83
- Pads
- 245
- Tracks, vias
- 532, 44
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 10 Mar 2020
- Updated
- 12 Jan 2023
Overview
NoPour is an open-source printed circuit board by plertvilai, from the plertvilai/IPAX repository on GitHub, published under the MIT licence. It is a 2-layer board of 45.7 × 66 mm with 68 parts on 83 nets, routed with 532 tracks and 44 vias.
It is built around the ATMEGA328P-AU and AP2112K-3.3. Its parts include 25 resistors, 15 connectors, 9 capacitors, 8 transistors and 7 ICs. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
2ATMEGA328P-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)AP2112K-3.3
SOT253.3V 600mA CMOS Low Dropout Linear Regulator with EnableDiodes IncorporatedUncategorised
README
README.mdIn Situ Plankton Assemblage eXplorer

This Github repository contains all information necessary to build the In Situ Plankton Assemblage eXplorer (IPAX). Here is a brief introduction to how to utilize the repository.
Detailed Guide
A detail building guide is given in the Building Guide subfolder. Note that this guide is written in HTML format. To read it, simply download the entire folder and use a browser to open the file index.html.
Fabrication Files
There are two folders containing files that are necessary for IPAX fabrication.
- Mechanicals contains STL files that can be directly sent to a 3D printer to printout the mechanical parts. A STEP file is also included for users that are interested to develop the system further. The STEP file Assembly Rev02 Revised for BES v3.step contains CAD files of all the parts, including waterproof housing from Bluerobotics that can be opened with a CAD software for further development.
- PCBs contains all files for the printed circuit boards in the IPAX. Each subfolder is for each PCB, and the folder fabrication contains Gerber files that can be sent directly to PCB manufacturers. Each subfolder also contains KiCAD files that users can use to develop the PCBs for fit their needs.
Firmware
The folder Firmware contains all software for the IPAX.
Control Board
This subfolder contains Arduino (.ino) files that can be uploaded to the control board of the IPAX.
- full_control_alwaysON is the main routine for the control board that set the Raspberry Pi to always ON.
- full_control_interval is the main routine for the control board that turns the Raspberry Pi ON only at the specified time.
- rtc_set is a temporary code that can be uploaded to the control board to set the real-time clock.
Raspberry Pi
This subfolder contains Python files for the Raspberry Pi on the IPAX.
- connectArduino.py is a routine that allows the Raspberry Pi to communicate with the Arduino on the control board.
- ipaxClass.py is the library for the IPAX.
- ipaxDeploy.py is the main routine for deploying the IPAX.
- shutdowncheck.py is the control script that allows the Raspberry Pi to be properly shutdown with an external switch on the housing and the control board.
The configuration subfolder contains all the configuration files needed to configure that Raspberry Pi.
Bill of Materials
The folder BOM contains a single MS Excel file (.xlsx) that contains the detailed bill of materials of the IPAX.
Parts
68| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 10k | Resistor_SMD:R_0603_1608Metric | R2, R4, R9, R10, R13, R15, R18, R23, R24 |
| 8 | R | Resistor_SMD:R_0603_1608Metric | R7, R16, R17, R19, R20, R21, R22, R25 |
| 7 | 400R | Resistor_SMD:R_0603_1608Metric | R1, R3, R5, R8, R11, R12, R14 |
| 5 | Conn_01x02_Male | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J2, J3, J7, J13, J15 |
| 5 | Conn_01x03_Male | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J4, J6, J8, J9, J14 |
| 4 | Q_NMOS_GSD | myLib:SOT-23-3 | Q2, Q4, Q6, Q8 |
| 4 | Q_PMOS_GSD | myLib:SOT-23-3 | Q1, Q3, Q5, Q7 |
| 3 | 1uF | Capacitor_SMD:C_0603_1608Metric | C1, C6, C7 |
| 3 | Conn_01x02_Male | Connector_PinHeader_2.00mm:PinHeader_1x02_P2.00mm_Vertical | J10, J11, J12 |
| 2 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C2, C5 |
| 2 | 1000uF | Capacitor_THT:CP_Radial_Tantal_D9.0mm_P5.00mm | C8, C9 |
| 2 | 22pF | Capacitor_SMD:C_0603_1608Metric | C3, C4 |
| 2 | LED | LED_SMD:LED_0603_1608Metric | D1, D7 |
| 1 | 0.01R | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | AP2112 | myLib:SOT-23-5 | U4 |
| 1 | ATmega328P-AU | Package_QFP:TQFP-32_7x7mm_P0.8mm | U1 |
| 1 | Conn_01x04_Male | Connector_PinHeader_2.00mm:PinHeader_1x04_P2.00mm_Vertical | J1 |
| 1 | Crystal | myLib:CRYSTAL_TH | Y1 |
| 1 | FTDI_Basic | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | U2 |
| 1 | LUXdriver | myLib:LUXdrive | U7 |
| 1 | MAX9938 | myLib:SOT-23-5 | U3 |
| 1 | OLED_I2C | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | U6 |
| 1 | Pi_Header | myLib:RPi_Cobbler | U5 |
| 1 | SW_DPST | myLib:SMD_pushbutton | SW1 |
| 1 | USB_B_Micro | myLib:USB_Micro-B_eBay | J5 |
More from plertvilai/IPAX
6- 2 layers44.5 × 57.8 mm

- 2 layers44.5 × 57.8 mm

- 2 layers

- 2 layers37.8 × 50 mm

- 2 layers

- 2 layers52.3 × 52.3 mm

Similar boards
- 2 layers52.3 × 63.6 mm

ATMEGA328 Heater
naufalra/AutomatedTissueProcessor_Final_Thesis_PT.Miconos
Developing and inverse engineering heater for tissue processor with a target to use local components (TKDN) for over 70%. The research is also used for my bachelor thesis.
64 parts1 - 2 layers63 × 88 mm

Paragon
timbalicious/netrunner_paragon_pcb
Possibly functional PCB alt-art Paragon for the Netrunner LCG
128 parts - 2 layers100 × 100 mm

- 2 layers80 × 110 mm

NucDeck Left Controller PCB
dmcke5/NucDeck
The Open Source DIY Handheld Gaming PC!
59 parts561CERN-OHL-S-2.0 - 2 layers50.5 × 128.5 mm

- 2 layers152 × 88 mm

RFBitBangSMT
profdc9/RFBitBanger
A QRP digital transceiver created from readily available parts for off-the-grid maintenance
271 parts222 - 2 layers50.2 × 31.2 mm

MCU Datalogger
futureshocked/KLP4e_MCU-Datalogger
This is the repository for the "MCU Datalogger" project.
31 parts138MIT - 2 layers34 × 46 mm

Questions
How big is the NoPour PCB?
It measures 45.7 × 66 mm and has 2 copper layers, 1.6 mm thick.
What parts does the NoPour use?
68 parts, built around the ATMEGA328P-AU and AP2112K-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the NoPour KiCad files?
From the plertvilai/IPAX repository on GitHub, at the commit this page was made from: the board is PCBs/Control_board/noPour.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the NoPour design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).