Skip to the content
2 layers100 × 48 mmTda8954-btl, the printed circuit board in 3D

PCB for TDA8954J Class-D amplifier

Size
100 × 48 mm
Copper layers
2
Thickness
1.6 mm
Parts
94
Nets
44
Pads
206
Tracks, vias
472, 21
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
30 Nov 2021
Updated
30 Nov 2021

Overview

Tda8954-btl is an open-source printed circuit board by phenidone, from the phenidone/tda8954-btl repository on GitHub. It is a 2-layer board of 100 × 48 mm with 94 parts on 44 nets, routed with 472 tracks and 21 vias.

It is built around the TDA8954J/N1, BSS84 and LL4148. Its parts include 36 capacitors, 24 resistors, 9 connectors, 4 diodes and 4 inductors. It belongs with the audio and music boards of this library.

Main components

3

README

README.md

TDA8954 Bridge Tied Load

This is a PCB design for a mono amplifier, using a TDA8954J in BTL configuration.

Power

The board requires 41+41V DC. Filtering caps are included, but a bridge rectifier is not as this is expected to be used with a switching supply.

The datasheet claims 420W into 8 ohms at 10% THD, or 330W at 0.5%, with a 41+41V supply.

The load impedance shall not be less than 8 ohms nominal.

Unmute

The muting circuits are controlled via an opto-isolated input. Provide 5-24VDC on the UNMUTE port to enable the amplifiers. This port allows the amplifier to be put into a standby/mute mode, e.g. while preamplifiers are booting.

Components

Input capacitors (C7, C10) shall be film-type box capacitors, 5mm lead pitch.

The capacitor voltage ratings required are as follows:

  • Single-rail electrolytics (470uF) should be 63V
  • Dual-rail electrolytics (22uF) should be 160V
  • Single-rail MLCC (mostly 100n) should be 100V
  • Dual-rail MLCC supply caps should be 250V
  • Bootstrap and snubber MLCCs should be 250V
  • Output LC filter caps (C5, C11) are to be high-voltage (400V) film type

The output LC inductors should be low-loss cores with a saturation current of not less than 10A. Footprints are provided for both Bourns SRP1265C (SMD shielded) and 2200HT-V (toroidal), though the toroids will overhang the edge of the PCB. If toroidal inductors are used, they should be affixed to the PCB with epoxy to prevent lead fatigue from vibration.

Power and output connectors are FASTON 1/4" spade terminals, though an extra footprint for a 3-way screw terminal is provided for power input.

EMI

The heatsink should be electrically connected to the HEATSINK spade terminal connector at the corner of the board, and/or connected to safety-ground.

License

This hardware design is (C) 2021 William Brodie-Tyrrell and is licensed under the CERN OHL; see cern_ohl_v_1_2.pdf

TRL

This PCB has been sent for manufacture but not yet assembled or tested.

Parts

94
QtyValueFootprintReferences
13100nCapacitors_SMD:C_0805C6, C12, C19, C20, C21, C22, C23, C30, C31, C32, C33, C34, C36
820Resistors_SMD:R_0805R1, R6, R7, R8, R20, R22, R23, R24
6Conn_01x01_Malepower:FASTON250P_5.08mm_male_verticalJ2, J4, J5, J8, J9, J10
4100Resistors_SMD:R_0805R13, R14, R15, R21
4220pCapacitors_SMD:C_0805C3, C4, C13, C14
43k9Resistors_SMD:R_0805R12, R16, R18, R19
4470uCapacitors_ThroughHole:CP_Radial_D13.0mm_P5.00mmC17, C18, C24, C25
4FiducialFiducials:Fiducial_1mm_Dia_2mm_OuterFID1, FID2, FID3, FID4
3LEDLEDs:LED_0805D1, D3, D4
2100nCapacitors_SMD:C_1206C28, C29
210kResistors_SMD:R_0805R9, R10
210uCapacitors_SMD:C_0805C16, C35
215nCapacitors_SMD:C_1206C8, C9
21uCapacitors_ThroughHole:C_Rect_L7.2mm_W3.5mm_P5.00mm_FKS2_FKP2_MKS2_MKP2C7, C10
222Resistors_ThroughHole:R_Axial_DIN0516_L15.5mm_D5.0mm_P5.08mm_VerticalR2, R5
222upower:SRP1265L2, L3
222uCapacitors_ThroughHole:CP_Radial_D10.0mm_P5.00mmC26, C27
222upower:Bourns-2200HT-VL1, L4
2680nCapacitors_ThroughHole:C_Rect_L18.0mm_W11.0mm_P15.00mm_FKS3_FKP3C5, C11
26k8Resistors_SMD:R_0805R11, R17
2BSS84TO_SOT_Packages_SMD:SOT-23Q1, Q2
2MountingHoleMounting_Holes:MountingHole_3.2mm_M3H1, H2
2Screw_Terminal_01x02Terminals_Phoenix:TerminalBlock_Phoenix_MPT-2.54mm_2polJ1, J6
11uCapacitors_SMD:C_0805C15
127kResistors_SMD:R_0805R4
12N7002TO_SOT_Packages_SMD:SOT-23Q3
12k7Resistors_SMD:R_0805R3
1470nCapacitors_SMD:C_0805C1
147pCapacitors_SMD:C_0805C2
1Jumper_NO_SmallPin_Headers:Pin_Header_Straight_1x02_Pitch2.54mmJP1
1LL4148Diodes_SMD:D_MiniMELFD2
1MCP1799TO_SOT_Packages_SMD:SOT-23U2
1PC817Housings_DIP:DIP-4_W7.62mm_SocketU3
1Screw_Terminal_01x03Terminals_Phoenix:TerminalBlock_Phoenix_MKDS1.5-3polJ7
1TDA8954Jpower:DBS23PU1

The 90 most common of 94 parts.

Similar boards

  • 2 layers100 × 65 mmTda7293, the printed circuit board in 3D

    Tda7293

    phenidone/tda7293-appnote

    PCB for TDA7293/TDA7294 amplifiers, per the datasheet suggestions

    77 parts2
  • 4 layers309.5 × 145 mmMicro HIL v0.1, the printed circuit board in 3D

    Micro HIL v0.1

    danielsimonreinhardt/microHIL

    microHIL is a self-developed testing device for setting up a basic hardware-in-the-loop environment

    396 partsMIT
  • 2 layers43.4 × 63 mmTapper, the printed circuit board in 3D

    Tapper

    rabinniroula/tapper-hw

    KiCad Design Files for Tapper: A hardware tool for LF and HF RFID read, emulation and much more...

    106 parts
  • 2 layers74.3 × 51.3 mmWago-859-SSD, the printed circuit board in 3D

    Wago-859-SSD

    TheBlueManCoding/Wago-859-SSD

    A PCB with electrical switches for 24V for the Wago 859 housing

    14 partsMIT
  • 2 layers35.6 × 27 mmWemosMosfet, the printed circuit board in 3D

    WemosMosfet

    TheBlueManCoding/WemosMosfet

    WemosMosfet

    26 partsCC0-1.0
  • 2 layers228.6 × 100 mmMongus48, the printed circuit board in 3D

    Mongus48

    ChrisChrisLoLo/beyblock20

    The magnetic, modular, 20-key macropad that can join together to form an ortholinear board

    124 parts335GPL-3.0
  • 2 layers80 × 129.1 mmSmart Plant, the printed circuit board in 3D

    Smart Plant

    JGAguado/Smart_Plant

    The Smart Plant is a board that can be plugged directly on the soil, close to the plant, that allows the measurement of the environment (soil moisture, environment temperature & illuminance), and presents the…

    75 parts303
  • 4 layers137 × 86 mmCIAA K60, the printed circuit board in 3D

    CIAA K60

    ciaa/Hardware

    Hardware de la CIAA

    467 parts216

Questions

How big is the Tda8954-btl PCB?

It measures 100 × 48 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Tda8954-btl use?

94 parts, built around the TDA8954J/N1, BSS84 and LL4148. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Tda8954-btl KiCad files?

From the phenidone/tda8954-btl repository on GitHub, at the commit this page was made from: the board is tda8954-btl.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Tda8954-btl design in my own project?

Its repository states no licence, so its author keeps all rights: ask phenidone before reusing the design.