

My own DIY Eurorack Modules
- Size
- 30 × 106 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 113
- Nets
- 74
- Pads
- 276
- Tracks, vias
- 754, 20
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 15 Apr 2021
- Updated
- 20 Apr 2021
Overview
Tribus is an open-source printed circuit board by pferreir, from the pferreir/eurorack-modules repository on GitHub. It is a 2-layer board of 30 × 106 mm with 113 parts on 74 nets, routed with 754 tracks and 20 vias.
It is built around the LM324, 78L05 and MMBT3904. Its parts include 47 resistors, 36 capacitors, 10 diodes, 6 transistors and 3 ICs.
Main components
3LM324
SOP-14-1.5V~10V 0℃~+70℃ 24V 250nA 3V~20V 4 40mA 50nA 700uA 7mV 80dB SOP-14 Operational Amplifier ROHSHXY MOSFETOperational Amplifier78L05
SOT-89-3-20℃~+120℃@(Tj) 1 1.7V 100mA 2mA 30V 40uV 49dB@(120Hz) 5V Fixed Over Temperature Protection、Short Circuit Protection Positive SOT-89-3 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSUMWVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsMMBT3904
SOT-23-55℃~+150℃ 1 NPN 100 100nA 200mA 200mW 300MHz 300mV 40V 6V NPN SOT-23 Bipolar (BJT) ROHSJiangsu Changjing Electronics Technology (CJ)Bipolar (BJT)
README
tribus/README.mdTribus
Monotribe Drums
https://www.muffwiggler.com/forum/viewtopic.php?p=3489026
ATTENTION: this design hasn't been tested yet. Build it at your own risk.
Parts
113| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 100nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C5, C6, C7, C8, C12, C25, C26, C28, C33 |
| 10 | 22K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R10, R18, R19, R21, R31, R32, R43, R45, R46, R53 |
| 8 | 1N4148 | Diode_SMD:D_SOD-123 | D4, D5, D6, D9, D10, D11, D12, D13 |
| 7 | 10K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R9, R22, R25, R30, R33, R51 |
| 7 | 15K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R34, R36, R37, R38, R39, R48, R50 |
| 6 | 100K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4, R5, R6, R23, R28, R55 |
| 6 | MMBT3904 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3, Q4, Q5, Q6 |
| 4 | 10nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C13, C23, C24, C27 |
| 4 | 18nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C29, C30, C32, C35 |
| 4 | 1M | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R12, R14, R41 |
| 3 | 10uF | Capacitor_SMD:CP_Elec_4x5.4 | C2, C3, C4 |
| 3 | 1nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C18, C19, C20 |
| 3 | 22pF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C11, C22, C37 |
| 3 | 27K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R27, R49, R52 |
| 3 | 3.3nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C14, C15, C16 |
| 3 | 470K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R40, R42 |
| 2 | 10K | Potentiometer_SMD:Potentiometer_Bourns_TC33X_Vertical | RV1, RV4 |
| 2 | 1K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R24, R58 |
| 2 | 1N5819 | Diode_SMD:D_SOD-123 | D1, D2 |
| 2 | 220 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R44, R47 |
| 2 | 27nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C34, C36 |
| 2 | 4.7nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C17, C31 |
| 2 | L_Small | Capacitor_SMD:C_0805_2012Metric | L1, L2 |
| 1 | 220K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R54 |
| 1 | 220nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C10 |
| 1 | 47uF | Capacitor_SMD:CP_Elec_4x5.4 | C9 |
| 1 | 680 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R35 |
| 1 | 78L05 | Package_TO_SOT_SMD:SOT-89-3_Handsoldering | U1 |
| 1 | 82K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R11 |
| 1 | Conn_01x08_Female | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J4 |
| 1 | Conn_01x08_Male | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J7 |
| 1 | Conn_02x05_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_Vertical | J1 |
| 1 | LM324 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U3 |
| 1 | NOISE_FILTER_Q | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | FILTER_Q |
| 1 | NOISE_TYPE | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | NOISE_TYPE |
| 1 | TL074 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U2 |
The 111 most common of 113 parts.
More from pferreir/eurorack-modules
2- 2 layers20 × 109 mm

- 2 layers30 × 106 mm

Similar boards
- 4 layers100 × 100 mm

TouchSynth
cpldcpu/TouchSynth
Analog Monophonic Synthesizer with a touch keyboard. Controller by CH32V00x
246 partsMIT - 2 layers36.8 × 34.7 mm

Tinylab proto1
espotek-org/Labrador
EspoTek Labrador is a USB device that transforms your PC or smartphone into a fully-featured electronics lab. This repo holds all of the source code!
79 parts1.2k - 2 layers33.2 × 34.6 mm

- 2 layers39.8 × 108.6 mm

KickAid Main
Thorinair/Avalon-Harmonics
A collection of Avalon Harmonics branded synthesizer modules.
79 parts26CC-BY-SA-4.0 - 2 layers100 × 80 mm

- 4 layers99 × 53.3 mm

PSLab
fossasia/pslab-hardware
PSLab Hardware Design and Schematics https://pslab.io
199 parts1.7kApache-2.0 - 4 layers133.9 × 165.1 mm

Main VCO board
JordanAceto/micro_ox
Monosynth with analog signal path and digital controls. SSI2130 VCOs and SSI2140 VCF.
295 parts8CC-BY-4.0 - 2 layers128 × 129 mm

Noise toaster
adeboni/eurorack
This repository stores various eurorack module designs I've made
133 parts1GPL-3.0
Questions
How big is the Tribus PCB?
It measures 30 × 106 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Tribus use?
113 parts, built around the LM324, 78L05 and MMBT3904. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Tribus KiCad files?
From the pferreir/eurorack-modules repository on GitHub, at the commit this page was made from: the board is tribus/tribus.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Tribus design in my own project?
Its repository states no licence, so its author keeps all rights: ask pferreir before reusing the design.