2 layers50.8 × 81.3 mm
4 layers50.8 × 81.3 mm
- Size
- 50.8 × 81.3 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 153
- Nets
- 97
- Pads
- 616
- Tracks, vias
- 1,129, 236
- Pours
- 19
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 3 Aug 2021
- Updated
- 6 Feb 2022
Overview
Allfc is an open-source printed circuit board by peregrine-developments, from the peregrine-developments/STACY repository on GitHub, published under the MIT licence. It is a 4-layer board of 50.8 × 81.3 mm with 153 parts on 97 nets, routed with 1,129 tracks and 236 vias.
It is built around the ATSAMD21G18A-AU, ATSAMD51J19A-AU and BMP388, with the S25FL064LABNFI043, BMI088 and MIC5216-3.3YMM among its other parts. Its parts include 48 capacitors, 48 resistors, 12 ICs, 10 connectors and 9 diodes. It belongs with the SAM D and SAM boards of this library.
Main components
9
ATSAMD21G18A-AU
TQFP-48-40℃~+85℃ 1.62V~3.6V 10bit 12bit 256KB 32 Bit 32KB 38 48MHz ARM Cortex-M0+ Built-in FLASH 上电复位(POR)、欠压检测(BOR/LVD/LVR/LVI)、看门狗复位、内置通用定时器、硬件CRC、日历功能、触控功能 TQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
ATSAMD51J19A-AU
TQFP-64-40℃~+85℃ 1.71V~3.63V 120MHz 12bit 12bit 192KB 32 Bit 51 512KB ARM Cortex-M4F Built-in FLASH TQFP-64(10x10) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
BMP388
LGA-10(2x2)-40℃~+85℃ 1.65V~3.6V 1pa/K 2uA 30Kpa~1.25bar 50pa 8pa I2C、SPI LGA-10(2x2) Pressure Sensors ROHSBosch SensortecPressure Sensors
S25FL064LABNFI043
USON-8-EP(4x4)USON-8-EP(4x4) NOR FLASH ROHSInfineon TechnologiesNOR FLASH
BMI088
LGA-16(3x4.5)-40℃~+85℃ Accelerometer Gyroscope LGA-16(3x4.5) Accelerometers ROHSBosch SensortecAccelerometers
MIC5216-3.3YMM
MSOP-8-40℃~+125℃ 1 12V 3.3V 500mA 600mV@(500mA) 75dB@(120Hz) Fixed Over Current Protection、Over Temperature Protection、Enable Positive MSOP-8 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMicrochip TechnologyVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
SP0503BAHTG
SOT-143-55℃~+125℃ 10A@8/20us 14V 150W@8/20us 30pF、60pF 5.5V 6V 80nA ESD IEC 61000-4-2、IEC 61000-4-5、IEC 61000-4-4 Three channels Unidirectional SOT-143 ESD and Surge Protection (TVS/ESD) ROHSTECH PUBLICESD And Surge Protection (TVS/ESD)
WS2812B-2020
SMD,2.2x2mm0.6mA 0.84mm 120us 160mcd 200mcd 2kHz 2mm 2mm 300ns 470.4nm 515.6nm 520mcd 5V 622.5nm 800Kbit/s Built-in power-on reset circuit、Built-in power-on reset circuit、Integrated intelligent reverse connection protection function Top-mount SMD,2.2x2mm RGB LEDs(Built-in IC) ROHSWorldsemiRGB LEDs(Built-In IC)
DMP3098L-7-ES
SOT-23-55℃~+150℃ 1 P-Channel 1.4W 30V 4.2A 42mΩ@10V、49mΩ@4.5V 47pF 510pF 54pF 800mV 9.4nC@4.5V P-Channel SOT-23 MOSFETs ROHSElecSuperMOSFETs
README
README.mdSTACY
Requires symbols/footprints from TheBoisCollective global library
Parts
153| Qty | Value | Footprint | References |
|---|---|---|---|
| 24 | 0.1u | Capacitor_SMD:C_0603_1608Metric | C1, C2, C10, C11, C12, C13, C14, C15, C17, C18, C19, C20, C21, C22, C26, C27 +8 |
| 11 | 10u | Capacitor_SMD:C_0603_1608Metric | C5, C29, C33, C35, C39, C43, C44, C45, C46, C47, C48 |
| 11 | TestPoint | TestPoint:TestPoint_THTPad_D1.0mm_Drill0.5mm | TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8, TP9, TP10, TP11 |
| 8 | 1k | Resistor_SMD:R_0603_1608Metric | R2, R9, R10, R21, R22, R34, R40, R46 |
| 8 | 4.7k | Resistor_SMD:R_0603_1608Metric | R5, R6, R7, R8, R11, R12, R16, R23 |
| 7 | 30.1k | Resistor_SMD:R_0603_1608Metric | R17, R24, R25, R26, R36, R42, R48 |
| 5 | 10k | Resistor_SMD:R_0603_1608Metric | R1, R4, R31, R37, R43 |
| 5 | 1u | Capacitor_SMD:C_0603_1608Metric | C6, C16, C23, C41, C42 |
| 5 | 470 | Resistor_SMD:R_0603_1608Metric | R13, R14, R35, R41, R47 |
| 5 | 86.6k | Resistor_SMD:R_0603_1608Metric | R19, R20, R32, R38, R44 |
| 4 | 18p | Capacitor_SMD:C_0402_1005Metric | C8, C9, C24, C25 |
| 4 | M2 | MountingHole:MountingHole_2.2mm_M2_Pad | H1, H2, H3, H4 |
| 3 | 47 | Resistor_SMD:R_0603_1608Metric | R33, R39, R45 |
| 3 | RED | LED_SMD:LED_0603_1608Metric | D6, D7, D8 |
| 3 | UCS3205 | TBC_QFN:VQFN19_3.0x3.0mm_2EP | U10, U11, U12 |
| 2 | 158k | Resistor_SMD:R_0603_1608Metric | R15, R18 |
| 2 | 180 | Resistor_SMD:R_0603_1608Metric | R28, R29 |
| 2 | 47p | Capacitor_SMD:C_0603_1608Metric | C32, C38 |
| 2 | 47u | Capacitor_SMD:C_0805_2012Metric | C36, C40 |
| 2 | 6.8u | Inductor_SMD:L_Bourns_SRP7028A_7.3x6.6mm | L1, L2 |
| 2 | AP63300WU-7 | SamacSys_Parts:SOT95P280X90-6N | U8, U9 |
| 2 | Crystal_Small | Crystal:Crystal_SMD_2012-2Pin_2.0x1.2mm | Y1, Y2 |
| 2 | SERIAL | Connector_JST:JST_GH_BM04B-GHS-TBT_1x04-1MP_P1.25mm_Vertical | J1, J9 |
| 2 | SP0503BAHT | Package_TO_SOT_SMD:SOT-143 | D2, D3 |
| 2 | WS2812B-2020 | TBC_LED:WS2812B-2020_2x2mm | D1, D4 |
| 1 | 4.7 | Resistor_SMD:R_2512_6332Metric | R3 |
| 1 | 82 | Resistor_SMD:R_0603_1608Metric | R27 |
| 1 | 820 | Resistor_SMD:R_0603_1608Metric | R30 |
| 1 | ATSAMD21G18A | Package_DFN_QFN:VQFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm | U6 |
| 1 | ATSAMD51J19A | Package_DFN_QFN:QFN-64-1EP_9x9mm_P0.5mm_EP4.7x4.7mm | U2 |
| 1 | BATT | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-3-2-5.08_1x02_P5.08mm_Horizontal | J2 |
| 1 | BMI088 | TBC_QFN:VQFN16_4.5x3.0mm | U5 |
| 1 | BMP388 | SamacSys_Parts:BMP388 | U4 |
| 1 | Buzz Aldrin | Buzzer_Beeper:Buzzer_CUI_CPT-9019S-SMT | BZ1 |
| 1 | CXDM4060P | Package_TO_SOT_SMD:SOT-89-3 | Q1 |
| 1 | DMP3098L-7 | Package_TO_SOT_SMD:SOT-23 | Q2 |
| 1 | D_Schottky_Small | Diode_SMD:D_SOD-323 | D5 |
| 1 | I2C | Connector_JST:JST_GH_BM04B-GHS-TBT_1x04-1MP_P1.25mm_Vertical | J8 |
| 1 | LIS3MDLTR | digikey-footprints:VFLGA-12_2x2mm | U3 |
| 1 | Micro_SD_Card | Connector_Card:microSD_HC_Hirose_DM3D-SF | J10 |
| 1 | ORANGE | LED_SMD:LED_0603_1608Metric | D9 |
| 1 | POW_EN | SamacSys_Parts:SW_SPDT_PCM12_HIDD | SW1 |
| 1 | PWM1 | TBC_Connectors:PinHeader_3x04_P2.54mm_Vertical | J6 |
| 1 | PWM1_P | Jumper:SolderJumper-3_P1.3mm_Bridged12_Pad1.0x1.5mm_NumberLabels | JP1 |
| 1 | PWM2 | TBC_Connectors:PinHeader_3x04_P2.54mm_Vertical | J7 |
| 1 | PWM2_P | Jumper:SolderJumper-3_P1.3mm_Bridged12_Pad1.0x1.5mm_NumberLabels | JP2 |
| 1 | PYROS | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-3-6-5.08_1x06_P5.08mm_Horizontal | J4 |
| 1 | PYR_EN | SamacSys_Parts:SW_SPDT_PCM12_HIDD | SW2 |
| 1 | S25FL064LABNFI043 | SamacSys_Parts:SON80P400X400X60-9N | U1 |
| 1 | USB_MCU | TBC_Connectors:USB_Micro-B_Molex_47346-0001_ShieldFloat | J3 |
| 1 | USB_NAV | TBC_Connectors:USB_Micro-B_Molex_47346-0001_ShieldFloat | J5 |
| 1 | MIC5216-3.3 | Package_TO_SOT_SMD:SOT-23-5 | U7 |
Questions
How big is the Allfc PCB?
It measures 50.8 × 81.3 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Allfc use?
153 parts, built around the ATSAMD21G18A-AU, ATSAMD51J19A-AU, BMP388 and S25FL064LABNFI043. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Allfc KiCad files?
From the peregrine-developments/STACY repository on GitHub, at the commit this page was made from: the board is allfc/allfc.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Allfc design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
More from peregrine-developments/STACY
1Similar boards
- 4 layers34 × 65 mm
- 2 layers68.6 × 53.3 mm
Adafruit adafruit metro m4 express airlift pcb metro m4 express airlift
oomlout/oomlout_oomp_project_bot_v_2
72 parts - 4 layers40 × 80 mm
- 2 layers99 × 58.5 mm
- 4 layers
SmartCompass
wildjames/smart_compass
The product is going to be something similar to the compass in the Pirates of the Caribbean.
78 parts - 6 layers16.4 × 33 mm
- 2 layers111 × 25 mm
Carrierboard teensy v3
ntnu-arl/embedded_rio-pcb
This is the PCB for the master thesis "Embedded Radar-Inertial Odometry". It is a carrier board built around a Teensy 4.0 that holds all the sensors and plugs into a Pixhawk flight controller.
21 parts6 - 2 layers30 × 40 mm
