Skip to the content

ATSAMD51J19A-AU

Microchip TechnologyExtended

-40℃~+85℃ 1.71V~3.63V 120MHz 12bit 12bit 192KB 32 Bit 51 512KB ARM Cortex-M4F Built-in FLASH TQFP-64(10x10) Microcontrollers (MCU/MPU/SOC) ROHS

Part id
microchip/ATSAMD51J19A-AU
Category
Microcontrollers (MCU, MPU, SOC)
Package
TQFP-64
Pins
64
In stock
144 at JLCPCB (C619369)
Used on
14 open-source boards

Overview

The ATSAMD51J19A-AU is a microcontroller made by Microchip Technology in a TQFP-64 package with 64 pins. -40℃~+85℃ 1.71V~3.63V 120MHz 12bit 12bit 192KB 32 Bit 51 512KB ARM Cortex-M4F Built-in FLASH TQFP-64(10x10) Microcontrollers (MCU/MPU/SOC) ROHS.

PCBKit's library has its KiCad symbol (MCU_Microchip_SAMD:ATSAMD51J19A-A, from KiCad's library) and its footprint (Package_QFP:TQFP-64_10x10mm_P0.5mm, from KiCad's library), ready for a KiCad board. 144 are in stock at JLCPCB (part C619369). 14 open-source boards in 10 repositories on GitHub use it.

Symbol

64PB031PA002PA013PA024PA035PB046PB057GNDANA8VDDANA9PB0610PB0711PB0812PB0913PA0414PA0515PA0616PA0717PA0818PA0919PA1020PA1121VDDIOB22GND23PB1024PB1125PB1226PB1327PB1428PB1529PA1230PA1331PA1432PA1534VDDIO35PA1636PA1737PA1838PA1939PB1640PB1741PA2042PA2143PA2244PA2345PA2446PA2548VDDIO49PB2250PB2351PA2752RESET53VDDCORE55VSW56VDDIO57PA3058PA3159PB3060PB3161PB0062PB0163PB02
MCU_Microchip_SAMD:ATSAMD51J19A-AFrom KiCad's library

Footprint

Package_QFP:TQFP-64_10x10mm_P0.5mmFrom KiCad's library

From the datasheet

9
Supply, least
1.71 V · VDDIO, recommended operating min · p. 1788
Supply, most
3.63 V · VDDIO, recommended operating max · p. 1788
Supply, absolute maximum
3.8 V · VDD, absolute max · p. 1787
Junction, hottest
145 °C · Junction temperature, absolute max · p. 1787
Takes asleep
17 µA · typical standby, BUCK, 3.3 V, fast wake-up disabled, no system RAM retained, 8 KB backup RAM retained · p. 1792
A pin gives at most
8 mA · max sink current, normal mode DRVSTR = 1, 3.0 V ≤ VDD ≤ 3.63 V · p. 1795
Junction to air (64-pin TQFP)
57.4 K/W · Junction-to-ambient thermal resistance · p. 1871
Junction to case (64-pin TQFP)
10.6 K/W · Junction-to-case thermal resistance · p. 1871
Takes asleep
191 nA · OFF mode typical at 1.8 V, 25°C · p. 1794

What it is and has

37
Core
120 MHz Arm Cortex-M4 · p. 1
Cache
4 KB combined instruction and data cache · p. 1
Memory protection
8-zone MPU · p. 1
Floating point
FPU · p. 1
Backup registers
Eight 32-bit registers · p. 1
Protection
Power-on Reset and Brown-out detection · p. 1
External interrupts
16 · p. 1
Non-maskable interrupt
1 · p. 1
Debug
Two-pin SWD programming, test and debugging · p. 1
Sleep modes
Idle, Standby, Hibernate, Backup, Off · p. 1
Power management
SleepWalking peripherals · p. 1
Backup power
Battery backup support · p. 1
Internal regulator
Selectable Buck/LDO · p. 1
Core performance
403 CoreMark at 120 MHz · p. 1
Cache
4 KB combined instruction cache and data cache · p. 1
Memory Protection Unit
8 zones · p. 1
Instruction set
Thumb-2 · p. 1
Instruction trace
Embedded Trace Module (ETM) with instruction trace stream · p. 1
Trace buffer
Core Sight Embedded Trace Buffer (ETB) · p. 1
Trace interface
Trace Port Interface Unit (TPIU) · p. 1
Floating Point Unit
FPU · p. 1
Flash error correction
Error Correction Code (ECC) · p. 1
Flash banks
Dual bank with Read-While-Write support · p. 1
EEPROM emulation
SmartEEPROM hardware emulation · p. 1
Supply supervision
Power-on Reset and Brown-out detection · p. 1
Clock options
Internal and external · p. 1
External Interrupt Controller
EIC · p. 1
Debug interface
Two-pin Serial Wire Debug programming, test, and debugging interface · p. 1
Trace
Embedded Trace Module with instruction trace stream · p. 1
Trace buffer
Core Sight Embedded Trace Buffer · p. 1
Trace interface
Trace Port Interface Unit · p. 1
Flash error correction
ECC · p. 1
Tightly Coupled Memory
Up to 4 KB · p. 1
Additional SRAM
Up to 8 KB · p. 1
Reset and supply monitoring
Power-on Reset and Brown-out detection · p. 1
Clocks
Internal and external clock options · p. 1
Debug interface
Two-pin SWD programming, test, and debugging · p. 1

Specifications

440
ParameterConditionsAs printedPage
Power supply voltage VDDmin 0 · max 3.8 V1787
Current into a VDD pin(2,3,4) IVDD64-pin package; maximum allowable current depends on device maximum power dissipationmax 60 mA1787
Current out of a GND pin IGNDmax 60 mA1787
Storage temperature Tstoragemin -60 · max 150 °C1787
Ambient temperature under bias (up to) TBIASmin -40 · max 125 °C1787
Junction temperature TJmin -40 · max 145 °C1787
Human Body Model (HBM) per JESD22-A114 VHBMESD qualificationmax 2000 V1787
Charged Device Model (CDM) AEC Q100-011 (ANSI/ESD STM 5.3.1) (PKG: Mid, corner) VCDMESD qualification; package middlemax 750 V1787
Charged Device Model (CDM) AEC Q100-011 (ANSI/ESD STM 5.3.1) (PKG: Mid, corner) VCDMESD qualification; package cornermax 750 V1787
IO Supply Voltage VDDIOBOD33 disabled, BOD12 enabled; same voltage as VDDANAmin 1.71 · typ 3.3 · max 3.63 V1788
IOB Supply Voltage VDDIOBBOD33 disabled, BOD12 enabled; lower than or equal to VDDIO and VDDANAmin 1.71 · typ 3.3 · max 3.63 V1788
Analog supply voltage VDDANABOD33 disabled, BOD12 enabled; same voltage as VDDIOmin 1.71 · typ 3.3 · max 3.63 V1788
Battery Supply Voltage VBATBOD33 disabled, BOD12 enabledmin 1.71 · typ 3.3 · max 3.63 V1788
Input Low Injection Current IICLAll pins; VIL source < (VSS - 0.6); characterized but not testedmin -15 mA1788
Input High Injection Current IICHAll I/O pins; VIH source > (VDDIO + 0.6)max 15 mA1788
Total Input Injection Current (Sum of all I/O and control pins) Absolute value of |∑IICT| ∑IICTAbsolute instantaneous sum of all positive and negative input injection currentsmax 45 mA1788
Peripheral, Internal regulator and IO Supply Voltages; Analog Supply Voltage VDDIO, VDDIOB, VDDANAFall rate; based on simulationmax 50 mV/us1789
Peripheral, Internal regulator and IO Supply Voltages; Analog Supply Voltage VDDIO, VDDIOB, VDDANARise rate; based on simulationmin 0.2 · max 100 mV/us1789
GCLK Generator Output Frequency fGCLKGEN0 / fGCLK_MAINundivided; generator 0 output must not exceed AHB clock frequencymax 200 MHz1789
GCLK Generator Output Frequency FgclkgenX, x={1;7}max 200 MHz1789
GCLK Generator Output Frequency FgclkgenX, , x={8;11}max 100 MHz1789
CPU clock frequency fCPUBased on simulationmax 120 MHz1789
AHB clock frequency fAHBBased on simulationmax 120 MHz1789
APBA, APBB, APBC and APBD clock frequency fAPBx, x = {A, B, C, D}Based on simulationmax 120 MHz1789
FDPLL0 and FDPLL1 Reference clock frequency fGCLK_DPLLx, x = {0,1}Based on simulationmax 3.2 MHz1789
FDPLL0 and FDPLL1 32k Reference clock frequency fGCLK_DPLLx_32K, x = {0,1}Based on simulationmax 100 kHz1789
DFLL48M Reference clock frequency fGCLK_DFLL48M_REFBased on simulationmax 33 kHz1789
EIC input clock frequency fGCLK_EICBased on simulationmax 100 MHz1789
FREQM Measure fGCLK_FREQM_MSRBased on simulationmax 200 MHz1789
FREQM Reference fGCLK_FREQM_REFBased on simulationmax 100 MHz1789
EVSYS channel x input clock frequency fGCLK_EVSYS_CHANNEL_x, x = {0, , 11}Based on simulationmax 100 MHz1789
Common SERCOMx slow input clock frequency fGCLK_SERCOMx_SLOW, x = {0, , 7}Based on simulationmax 12 MHz1789
SERCOMx input clock frequency fGCLK_SERCOMx_CORE, x = {0, , 7}Based on simulationmax 100 MHz1789
CANx input clock frequency fGCLK_CANx, x = {0, 1}Based on simulationmax 100 MHz1789
USB input clock frequency fGCLK_USBBased on simulationmax 60 MHz1790
I2S input clock frequency fGCLK_I2SBased on simulationmax 100 MHz1790
Common SDHCx slow input clock frequency fGCLK_SDHCx_SLOW, x = {0, 1}Based on simulationmax 12 MHz1790
SDHCx input clock frequency fGCLK_SDHCx_CORE, x = {0, 1}Based on simulationmax 150 MHz1790
TCCx input clock frequency fGCLK_TCCx, x = {0, , 4}Based on simulationmax 200 MHz1790
TC0, TC1, TC2, TC3 input clock frequency fGCLK_TCx, x = {0, , 3}Based on simulationmax 200 MHz1790
TC4, TC5, TC6, TC7 input clock frequency fGCLK_TCx, x = {4, , 7}Based on simulationmax 100 MHz1790
PDEC input clock frequency fGCLK_PDECBased on simulationmax 200 MHz1790
CCL input clock frequency fGCLK_CCLBased on simulationmax 100 MHz1790
External GCLK input clock frequency fGCLK_GCLKINBased on simulationmax 50 MHz1790
CM4 Trace input clock frequency fGCLK_CM4_TRACEBased on simulationmax 120 MHz1790
AC digital input clock frequency fGCLK_ACBased on simulationmax 100 MHz1790
ADCx input clock frequency fGCLK_ADCx, x = {0, 1}Based on simulationmax 100 MHz1790
DAC input clock frequency fGCLK_DACBased on simulationmax 100 MHz1790
ActiveCOREMARK; LDO; FDPLL 120 MHz; VDD = 1.8V; typical at 25°C, max at 85°Ctyp 136 · max 162 uA/MHz1791
ActiveCOREMARK; LDO; FDPLL 120 MHz; VDD = 3.3V; typical at 25°C, max at 85°Ctyp 137 · max 164 uA/MHz1791
ActiveCOREMARK; LDO; DFLL 48 MHz; VDD = 1.8V; typical at 25°C, max at 85°Ctyp 136 · max 199 uA/MHz1791
ActiveCOREMARK; LDO; DFLL 48 MHz; VDD = 3.3V; typical at 25°C, max at 85°Ctyp 136 · max 199 uA/MHz1791
ActiveCOREMARK; LDO; XOSC 32 MHz; VDD = 1.8V; typical at 25°C, max at 85°Ctyp 146 · max 243 uA/MHz1791
ActiveCOREMARK; LDO; XOSC 32 MHz; VDD = 3.3V; typical at 25°C, max at 85°Ctyp 149 · max 245 uA/MHz1791
ActiveCOREMARK; BUCK; FDPLL 120 MHz; VDD = 1.8V; typical at 25°C, max at 85°Ctyp 103 · max 127 uA/MHz1791
ActiveCOREMARK; BUCK; FDPLL 120 MHz; VDD = 3.3V; typical at 25°C, max at 85°Ctyp 65 · max 89 uA/MHz1791
ActiveCOREMARK; BUCK; DFLL 48 MHz; VDD = 1.8V; typical at 25°C, max at 85°Ctyp 102 · max 152 uA/MHz1791
ActiveCOREMARK; BUCK; DFLL 48 MHz; VDD = 3.3V; typical at 25°C, max at 85°Ctyp 63 · max 115 uA/MHz1791
ActiveCOREMARK; BUCK; XOSC 32 MHz; VDD = 1.8V; typical at 25°C, max at 85°Ctyp 110 · max 205 uA/MHz1791
ActiveCOREMARK; BUCK; XOSC 32 MHz; VDD = 3.3V; typical at 25°C, max at 85°Ctyp 73 · max 153 uA/MHz1791
IdleLDO; FDPLL 120 MHz; VDD = 1.8V; typical at 25°C, max at 85°Ctyp 21 · max 46 uA/MHz1791
IdleLDO; FDPLL 120 MHz; VDD = 3.3V; typical at 25°C, max at 85°Ctyp 23 · max 48 uA/MHz1791
IdleLDO; DFLL 48 MHz; VDD = 1.8V; typical at 25°C, max at 85°Ctyp 21 · max 84 uA/MHz1791
IdleLDO; DFLL 48 MHz; VDD = 3.3V; typical at 25°C, max at 85°Ctyp 21 · max 84 uA/MHz1791
IdleLDO; XOSC 32 MHz; VDD = 1.8V; typical at 25°C, max at 85°Ctyp 25 · max 115 uA/MHz1791
IdleLDO; XOSC 32 MHz; VDD = 3.3V; typical at 25°C, max at 85°Ctyp 27 · max 117 uA/MHz1791
IdleBUCK; FDPLL 120 MHz; VDD = 1.8V; typical at 25°C, max at 85°Ctyp 16 · max 35 uA/MHz1791
IdleBUCK; FDPLL 120 MHz; VDD = 3.3V; typical at 25°C, max at 85°Ctyp 11 · max 28 uA/MHz1791
IdleBUCK; DFLL 48 MHz; VDD = 1.8V; typical at 25°C, max at 85°Ctyp 16 · max 63 uA/MHz1791
IdleBUCK; DFLL 48 MHz; VDD = 3.3V; typical at 25°C, max at 85°Ctyp 10 · max 46 uA/MHz1791
IdleBUCK; XOSC 32 MHz; VDD = 1.8V; typical at 25°C, max at 85°Ctyp 21 · max 90 uA/MHz1791
IdleBUCK; XOSC 32 MHz; VDD = 3.3V; typical at 25°C, max at 85°Ctyp 19 · max 71 uA/MHz1791
StandbyLDO; VDD = 1.8V; FASTWKUP = 0x0; no peripheral running; RAMCFG = 0x2, no system RAM retained; 8 KB backup RAM retained; typical at 25°C, max at 85°Ctyp 43 · max 870 uA1792
StandbyLDO; VDD = 3.3V; FASTWKUP = 0x0; no peripheral running; RAMCFG = 0x2, no system RAM retained; 8 KB backup RAM retained; typical at 25°C, max at 85°Ctyp 43 · max 869 uA1792
StandbyBUCK; VDD = 1.8V; FASTWKUP = 0x0; no peripheral running; RAMCFG = 0x2, no system RAM retained; 8 KB backup RAM retained; typical at 25°C, max at 85°Ctyp 26 · max 570 uA1792
StandbyBUCK; VDD = 3.3V; FASTWKUP = 0x0; no peripheral running; RAMCFG = 0x2, no system RAM retained; 8 KB backup RAM retained; typical at 25°C, max at 85°Ctyp 17 · max 440 uA1792
StandbyLDO; VDD = 1.8V; FASTWKUP = 0x3; no peripheral running; RAMCFG = 0x2, no system RAM retained; 8 KB backup RAM retained; typical at 25°C, max at 85°Ctyp 85 · max 1388 uA1792
StandbyLDO; VDD = 3.3V; FASTWKUP = 0x3; no peripheral running; RAMCFG = 0x2, no system RAM retained; 8 KB backup RAM retained; typical at 25°C, max at 85°Ctyp 85 · max 1392 uA1792
StandbyBUCK; VDD = 1.8V; FASTWKUP = 0x3; no peripheral running; RAMCFG = 0x2, no system RAM retained; 8 KB backup RAM retained; typical at 25°C, max at 85°Ctyp 65 · max 1047 uA1792
StandbyBUCK; VDD = 3.3V; FASTWKUP = 0x3; no peripheral running; RAMCFG = 0x2, no system RAM retained; 8 KB backup RAM retained; typical at 25°C, max at 85°Ctyp 47 · max 738 uA1792
StandbyLDO; VDD = 1.8V; FASTWKUP = 0x0; RTC on XOSC32K; RAMCFG = 0x2, no system RAM retained; 8 KB backup RAM retained; typical at 25°C, max at 85°Ctyp 43 · max 870 uA1792
StandbyLDO; VDD = 3.3V; FASTWKUP = 0x0; RTC on XOSC32K; RAMCFG = 0x2, no system RAM retained; 8 KB backup RAM retained; typical at 25°C, max at 85°Ctyp 44 · max 870 uA1792
StandbyBUCK; VDD = 1.8V; FASTWKUP = 0x0; RTC on XOSC32K; RAMCFG = 0x2, no system RAM retained; 8 KB backup RAM retained; typical at 25°C, max at 85°Ctyp 26 · max 571 uA1792
StandbyBUCK; VDD = 3.3V; FASTWKUP = 0x0; RTC on XOSC32K; RAMCFG = 0x2, no system RAM retained; 8 KB backup RAM retained; typical at 25°C, max at 85°Ctyp 18 · max 443 uA1792
StandbyLDO; VDD = 1.8V; FASTWKUP = 0x0; RTC on XOSC32K; RAMCFG = 0x1, 32 KB system RAM retained; 8 KB backup RAM retained; typical at 25°C, max at 85°Ctyp 45 · max 912 uA1792
StandbyLDO; VDD = 3.3V; FASTWKUP = 0x0; RTC on XOSC32K; RAMCFG = 0x1, 32 KB system RAM retained; 8 KB backup RAM retained; typical at 25°C, max at 85°Ctyp 46 · max 911 uA1792
StandbyBUCK; VDD = 1.8V; FASTWKUP = 0x0; RTC on XOSC32K; RAMCFG = 0x1, 32 KB system RAM retained; 8 KB backup RAM retained; typical at 25°C, max at 85°Ctyp 27 · max 598 uA1792
StandbyBUCK; VDD = 3.3V; FASTWKUP = 0x0; RTC on XOSC32K; RAMCFG = 0x1, 32 KB system RAM retained; 8 KB backup RAM retained; typical at 25°C, max at 85°Ctyp 19 · max 462 uA1792
StandbyLDO; VDD = 1.8V; FASTWKUP = 0x0; RTC on XOSC32K; RAMCFG = 0x0, full system RAM retained; 8 KB backup RAM retained; typical at 25°C, max at 85°Ctyp 53 · max 1068 uA1792
StandbyLDO; VDD = 3.3V; FASTWKUP = 0x0; RTC on XOSC32K; RAMCFG = 0x0, full system RAM retained; 8 KB backup RAM retained; typical at 25°C, max at 85°Ctyp 53 · max 1067 uA1792
StandbyBUCK; VDD = 1.8V; FASTWKUP = 0x0; RTC on XOSC32K; RAMCFG = 0x0, full system RAM retained; 8 KB backup RAM retained; typical at 25°C, max at 85°Ctyp 32 · max 702 uA1792
StandbyBUCK; VDD = 3.3V; FASTWKUP = 0x0; RTC on XOSC32K; RAMCFG = 0x0, full system RAM retained; 8 KB backup RAM retained; typical at 25°C, max at 85°Ctyp 22 · max 537 uA1792
StandbyLDO; VDD = 1.8V; FASTWKUP = 0x3; no peripheral running; full system RAM retained; typical at 25°C, max at 85°Ctyp 101 · max 1716 uA1792
StandbyLDO; VDD = 3.3 V; FASTWKUP = 0x3; no peripheral running; full system RAM retained; typical at 25°C, max at 85°Ctyp 101 · max 1722 uA1792
StandbyBUCK; VDD = 1.8V; FASTWKUP = 0x3; no peripheral running; full system RAM retained; typical at 25°C, max at 85°Ctyp 78 · max 1298 uA1792
StandbyBUCK; VDD = 3.3V; FASTWKUP = 0x3; no peripheral running; full system RAM retained; typical at 25°C, max at 85°Ctyp 55 · max 911 uA1792
StandbyLDO; VDD = 1.8V; FASTWKUP = 0x3; RTC on XOSC32K; full system RAM retained; typical at 25°C, max at 85°Ctyp 102 · max 1724 uA1792
StandbyLDO; VDD = 3.3V; FASTWKUP = 0x3; RTC on XOSC32K; full system RAM retained; typical at 25°C, max at 85°Ctyp 103 · max 1732 uA1792
StandbyBUCK; VDD = 1.8V; FASTWKUP = 0x3; RTC on XOSC32K; full system RAM retained; typical at 25°C, max at 85°Ctyp 79 · max 1305 uA1792
StandbyBUCK; VDD = 3.3V; FASTWKUP = 0x3; RTC on XOSC32K; full system RAM retained; typical at 25°C, max at 85°Ctyp 56 · max 915 uA1792
OFFtyp 210 us1795
Pull-up/Pull-down Resistance RPULLmin 20 · typ 40 · max 60 kΩ1795
Pull-down resistance on pads PA24 and PA25min 14 · typ 23 · max 28 kΩ1795
Input Leakage Current ILEAKPull-up resistors disabled; typical = ±0.015min -1 · max 1 uA1795
Maximum Output low-level current IOL1.71V<= VDD <3.0V; Backup Pins in Backup Modemax 0.005 mA1795
Maximum Output low-level current IOL1.71V<= VDD <3.0V; Normal Mode (all IO pins), DRVSTR = 0max 0.5 mA1795
Maximum Output low-level current IOL1.71V<= VDD <3.0V; Normal Mode (all IO pins), DRVSTR = 1max 3 mA1795
Maximum Output low-level current IOL3.0V <= VDD <= 3.63V; Backup Pins in Backup Modemax 0.01 mA1795
Maximum Output low-level current IOL3.0V <= VDD <= 3.63V; Normal Mode (all IO pins), DRVSTR = 0max 2 mA1795
Maximum Output low-level current IOL3.0V <= VDD <= 3.63V; Normal Mode (all IO pins), DRVSTR = 1max 8 mA1795
Maximum Output high-level current IOH1.71V <= VDD < 3.0V; Backup Pins in Backup Modemax 0.005 mA1795
Maximum Output high-level current IOH1.71V <= VDD < 3.0V; Normal Mode (all IO pins), DRVSTR = 0max 0.5 mA1795
Maximum Output high-level current IOH1.71V <= VDD < 3.0V; Normal Mode (all IO pins), DRVSTR = 1max 3 mA1795
Maximum Output high-level current IOH3.0V <= VDD <= 3.63V; Backup Pins in Backup Modemax 0.01 mA1795
Maximum Output high-level current IOH3.0V <= VDD <= 3.63V; Normal Mode (all IO pins), DRVSTR = 0max 2 mA1795
Maximum Output high-level current IOH3.0V <= VDD <= 3.63V; Normal Mode (all IO pins), DRVSTR = 1max 8 mA1795
Maximum Rise Time tRISECLOAD = 30 pF; Backup Pins in Backup Modemax 4 us1795
Maximum Rise Time tRISECLOAD = 30 pF; Normal Mode (all I/O pins), DRVSTR = 0max 0.04 us1795
Maximum Rise Time tRISECLOAD = 30 pF; Normal Mode (all I/O pins), DRVSTR = 1max 0.01 us1795
Maximum Fall Time tFALLCLOAD = 30 pF; Backup Pins in Backup Modemax 4 us1795
Maximum Fall Time tFALLCLOAD = 30 pF; Normal Mode (all I/O pins), DRVSTR = 0max 0.04 us1795
Maximum Fall Time tFALLCLOAD = 30 pF; Normal Mode (all I/O pins), DRVSTR = 1max 0.01 us1795
Operating Ambient Temperature Range TAIndustrial Temperature Devicesmin -40 · max 85 °C1871
Operating Junction Temperature Range TJIndustrial Temperature Devicesmax 105 °C1871
Operating Ambient Temperature Range TAV-temp Temperature Devicesmin -40 · max 105 °C1871
Operating Junction Temperature Range TJV-temp Temperature Devicesmax 125 °C1871
Power supply voltage VDDVDD represents the common voltage applied to VDDIO and VDDANAmin 0 · max 3.8 V1787
Current into a VDD pin IVDDMaximum allowable current depends on device maximum power dissipationmax 60 mA1787
Charged Device Model (CDM) AEC Q100-011 (ANSI/ESD STM 5.3.1) VCDMESD qualification; PKG: Midmax 750 V1787
Charged Device Model (CDM) AEC Q100-011 (ANSI/ESD STM 5.3.1) VCDMESD qualification; PKG: cornermax 750 V1787
BackupPowered by VDDIO, no RTC running; VDDIO+VDDANA consumption; no backup RAM retained (PM.BKUPCFG.BRAMCFG = 0x2); VDD = 1.8V; typ. 25°C, max. 85°Ctyp 2.1 · max 41.7 uA1794
BackupPowered by VDDIO, no RTC running; VDDIO+VDDANA consumption; no backup RAM retained (PM.BKUPCFG.BRAMCFG = 0x2); VDD = 3.3V; typ. 25°C, max. 85°Ctyp 2.5 · max 42.5 uA1794
BackupPowered by VDDIO with RTC running on XOSC32K; VDDIO+VDDANA consumption; no backup RAM retained (PM.BKUPCFG.BRAMCFG = 0x2); VDD = 1.8V; typ. 25°C, max. 85°Ctyp 2.7 · max 42.6 uA1794
BackupPowered by VDDIO with RTC running on XOSC32K; VDDIO+VDDANA consumption; no backup RAM retained (PM.BKUPCFG.BRAMCFG = 0x2); VDD = 3.3V; typ. 25°C, max. 85°Ctyp 3.3 · max 43.6 uA1794
BackupPowered by VDDIO, no RTC running; VDDIO+VDDANA consumption; 4 KB backup RAM retained (PM.BKUPCFG.BRAMCFG = 0x1); VDD = 1.8V; typ. 25°C, max. 85°Ctyp 2.4 · max 48.4 uA1794
BackupPowered by VDDIO, no RTC running; VDDIO+VDDANA consumption; 4 KB backup RAM retained (PM.BKUPCFG.BRAMCFG = 0x1); VDD = 3.3V; typ. 25°C, max. 85°Ctyp 2.8 · max 49.1 uA1794
BackupPowered by VDDIO, no RTC running; VDDIO+VDDANA consumption; 8 KB backup RAM retained (PM.BKUPCFG.BRAMCFG = 0x0); VDD = 1.8V; typ. 25°C, max. 85°Ctyp 2.7 · max 55.1 uA1794
BackupPowered by VDDIO, no RTC running; VDDIO+VDDANA consumption; 8 KB backup RAM retained (PM.BKUPCFG.BRAMCFG = 0x0); VDD = 3.3V; typ. 25°C, max. 85°Ctyp 3.1 · max 55.8 uA1794
BackupBattery backup mode powered by VBAT with RTC running on XOSC32K; 1.8V; typ. 25°C, max. 85°Ctyp 2.7 · max 42.6 uA1794
BackupBattery backup mode powered by VBAT with RTC running on XOSC32K; 3.3V; typ. 25°C, max. 85°Ctyp 3.3 · max 43.6 uA1794
OFFVDD = 1.8V; typ. 25°C, max. 85°Ctyp 0.191 · max 2.3 uA1794
OFFVDD = 3.3V; typ. 25°C, max. 85°Ctyp 0.331 · max 3.35 uA1794
IDLEVDD = 3.3V; LDO regulation; CPU clock DFLL48 open loop; automatic NVM wait state and cache enabledtyp 230 ns1794
STANDBYSTDBYCFG.FASTWKUP = 0; VDD = 3.3V; LDO regulation; CPU clock DFLL48 open loop; automatic NVM wait state and cache enabledtyp 110 us1794
STANDBYSTDBYCFG.FASTWKUP = 1; Fast Wakeup enabled on NVM; VDD = 3.3V; LDO regulation; CPU clock DFLL48 open loop; automatic NVM wait state and cache enabledtyp 92 us1794
STANDBYSTDBYCFG.FASTWKUP = 2; Fast Wakeup enabled on main voltage regulator; VDD = 3.3V; LDO regulation; CPU clock DFLL48 open loop; automatic NVM wait state and cache enabledtyp 25 us1794
STANDBYSTDBYCFG.FASTWKUP = 3; Fast Wakeup enabled on NVM and MAINVREG; VDD = 3.3V; LDO regulation; CPU clock DFLL48 open loop; automatic NVM wait state and cache enabledtyp 5 us1794
HibernateVDD = 3.3V; LDO regulation; CPU clock DFLL48 open loop; automatic NVM wait state and cache enabledtyp 320 us1794
BACKUPVDD = 3.3V; LDO regulation; CPU clock DFLL48 open loop; automatic NVM wait state and cache enabledtyp 350 us1794
Power Efficiency PEFFIOUT = 100uAtyp 66 %1796
Power Efficiency PEFFIOUT = 100mAtyp 74 %1796
Input regulator decoupling capacitors on VDDIO, VDDIOB and VDDANA CINtyp 10 uF1796
Input regulator decoupling capacitors on VDDIO, VDDIOB and VDDANA CINCeramic dielectric X7Rtyp 100 nF1796
Output regulator decoupling capacitors on VDDCORE COUTmin 3.76 · typ 4.7 uF1796
Output regulator decoupling capacitors on VDDCORE COUTCeramic dielectric X7Rtyp 100 nF1796
External Series Resistance of COUT ESR COUTmax 0.5 Ω1796
External inductance LEXTtyp 10 uH1796
ESR of LEXT RSERIES_LEXTmax 0.36 Ω1796
Saturation current ISAT_LEXTmin 500 mA1796
Input regulator decoupling capacitors on VDDIO, VDDIOB and VDDANA CINtyp 10 uF1796
Input regulator decoupling capacitors on VDDIO, VDDIOB and VDDANA CINCeramic dielectric X7Rtyp 100 nF1796
ADC Sample Time TSAMPTAD(min) Ext Analog Input Rsource ≤ 147 Ωmin 1 TAD1802
ADC Sample Time TSAMPTAD(min), Ext Analog Input Rsource ≤ 2,250 Ωmin 2 TAD1802
ADC Sample Time TSAMPTAD(min), Ext Analog Input Rsource ≤ 4,400 Ωmin 3 TAD1802
ADC Sample Time TSAMPTAD(min), Ext Analog Input Rsource ≤ 6,550 Ωmin 4 TAD1802
ADC Sample Time TSAMPTAD(min), Ext Analog Input Rsource ≤ 8,700 Ωmin 5 TAD1802
ADC Sample Time TSAMPTAD(min), Ext Analog Input Rsource ≤ 10,850 Ωmin 6 TAD1802
ADC Sample Time TSAMPSample time with Temp sensor or band gap as inputmin 10000 ns1802
Conversion Time (3) (Single-Ended Mode) TCNV12-bit resolutiontyp 12 TAD1802
Conversion Time (3) (Single-Ended Mode) TCNV10-bit resolutiontyp 11 TAD1802
Conversion Time (3) (Single-Ended Mode) TCNV8-bit resolutiontyp 9 TAD1802
Conversion Time (3) (Differential Mode) TCNV12-bit resolutiontyp 12 TAD1802
Conversion Time (3) (Differential Mode) TCNV10-bit resolutiontyp 10 TAD1802
Conversion Time (3) (Differential Mode) TCNV8-bit resolutiontyp 8 TAD1802
ADC Internal Sample Cap CSAMPLEmin 2 · max 3 pf1802
ADC Internal impedance RSAMPLEmax 2000 Ω1802
Resolution ResSelectable 8, 10, 12 bit Resolution Rangesmin 8 · max 12 bits1802
Effective Number of bits EN0B1msps, R2R disabled, VREF = VDDANA = VDDIO = 3.0min 10.5 bits1802
Effective Number of bits EN0B1msps, R2R disabled, External VREF = 2.0V, VDDANA = VDDIO = 3.0min 10.5 bits1802
Differential Mode, DC supply current, 2 output channels - without load IDDANAfs = 1 Msps, CCTR L= 0x2, VREF > 2.4V, VDD = 3.3V; typ. 25°C, max. 85°Ctyp 384 · max 540 uA1807
Differential Mode, DC supply current, 2 output channels - without load IDDANAfs = 10 ksps, CCTRL = 0x0, VREF < 2.4V, VDD = 3.3V; typ. 25°C, max. 85°Ctyp 283 · max 411 uA1807
Single-Ended Mode, DC supply current, 2 output channels - without load IDDANAfs = 1 Msps, CCTRL = 0x2, VREF > 2.4V, VDD = 3.3V; typ. 25°C, max. 85°Ctyp 306 · max 443 uA1807
Single-Ended Mode, DC supply current, 2 output channels - without load IDDANAfs = 10 ksps, CCTRL = 0x0, VREF < 2.4V, VDD = 3.3V; typ. 25°C, max. 85°Ctyp 230 · max 332 uA1807
Comparator Negative and positive input signal range PNIVRVDD = 1.71V to 3.63V; Max. VDDANAmin 0 V1807
Input common mode range ICMRVDD = 1.71V to 3.63V; Max. VDDANA-0.2min 0 V1807
Offset OffHigh speed COMPCTRLn.SPEED = 0x3; hysteresis disabledmin -18 · max 18 mV1807
Propagation Delay TpdVcm=VDDANA/2, Vin = +/-100mV overdrive from Vcm; High speed COMPCTRLn.SPEED = 0x3typ 24.1 · max 39 ns1807
Startup time TstartHigh speed COMPCTRLn.SPEED = 0x3typ 4.7 · max 7.5 us1807
Current consumption for One AC enabled, Hysteresis disabled voltage scaler disabled IDDANACOMPCTRLn.SPEED=0x3, VDDANA=3.3V; typ. 25°C, max. 85°Ctyp 59 · max 93 uA1807
Current consumption Voltage Scaler only IDDANAVDDANA=3.3V; typ. 25°C, max. 85°Ctyp 11 · max 21 uA1807
Gain GainGAIN_1; Averagetyp 11810
Gain GainGAIN_2; Averagetyp 21810
Gain GainGAIN_4; Averagetyp 4.21810
Gain GainGAIN_16; Average; setting not recommendedtyp 15.41810
Current Consumption IDDPTC scan rate 10 msec; 4 oversamples; VDD = 3.0V; CPU 48 MHz from flash, 2 wait states; PTC 4 MHz; mutual capacitance, one channel; standby sleep; RTC ULP32K; typ. 25°C, max. 85°Ctyp 137 · max 1164 uA1810
Current Consumption IDDPTC scan rate 10 msec; 16 oversamples; VDD = 3.0V; CPU 48 MHz from flash, 2 wait states; PTC 4 MHz; mutual capacitance, one channel; standby sleep; RTC ULP32K; typ. 25°C, max. 85°Ctyp 146 · max 1179 uA1810
Current Consumption IDDPTC scan rate 50 msec; 4 oversamples; VDD = 3.0V; CPU 48 MHz from flash, 2 wait states; PTC 4 MHz; mutual capacitance, one channel; standby sleep; RTC ULP32K; typ. 25°C, max. 85°Ctyp 77 · max 1094 uA1810
Current Consumption IDDPTC scan rate 50 msec; 16 oversamples; VDD = 3.0V; CPU 48 MHz from flash, 2 wait states; PTC 4 MHz; mutual capacitance, one channel; standby sleep; RTC ULP32K; typ. 25°C, max. 85°Ctyp 79 · max 1100 uA1810
Current Consumption IDDPTC scan rate 100 msec; 4 oversamples; VDD = 3.0V; CPU 48 MHz from flash, 2 wait states; PTC 4 MHz; mutual capacitance, one channel; standby sleep; RTC ULP32K; typ. 25°C, max. 85°Ctyp 68 · max 1086 uA1810
Current Consumption IDDPTC scan rate 100 msec; 16 oversamples; VDD = 3.0V; CPU 48 MHz from flash, 2 wait states; PTC 4 MHz; mutual capacitance, one channel; standby sleep; RTC ULP32K; typ. 25°C, max. 85°Ctyp 69 · max 1089 uA1810
Current Consumption IDDPTC scan rate 200 msec; 4 oversamples; VDD = 3.0V; CPU 48 MHz from flash, 2 wait states; PTC 4 MHz; mutual capacitance, one channel; standby sleep; RTC ULP32K; typ. 25°C, max. 85°Ctyp 64 · max 1085 uA1810
Current Consumption IDDPTC scan rate 200 msec; 16 oversamples; VDD = 3.0V; CPU 48 MHz from flash, 2 wait states; PTC 4 MHz; mutual capacitance, one channel; standby sleep; RTC ULP32K; typ. 25°C, max. 85°Ctyp 65 · max 1087 uA1810
Crystal oscillator frequency FOUTtyp 32.768 kHz1815
Crystal load capacitance CLmax 12.5 pF1815
Crystal Equivalent Series Resistance - SF=3 ESRf=32.768 kHz, CL=12.5 pF; Std. Gainmax 58 kΩ1815
XIN32 pin capacitance CXIN32ktyp 3.1 pF1815
XOUT32 pin capacitance CXOUT32ktyp 3.2 pF1815
Current consumption IDDVDD=3.0V; Std. Gain Mode; typ. 25°C, max. 85°Ctyp 1.5 · max 2 uA1815
Current consumption IDDVDD=3.0V; High Gain Mode; typ. 25°C, max. 85°Ctyp 1.9 · max 3 uA1815
Output frequency FOUT[-40, +85]°C, VDDANA>1.71Vmin 27.12 · typ 32.768 · max 37.68 kHz1815
Calibration step Steptyp 1.5 %FOUT1815
Duty Cycle Dutytyp 50 %1815
Run-time Calibration RuntimeCalCPU clock on DFLL (48 MHz)max 5 ms1815
Period Jitter FCloseJitterfREF = XTAL, 32.768 kHz, 100 ppm; DFLLMUL = 1464max 0.42 ns1817
Lock time TLockFREF = XTAL, 32.768 kHz, 100 ppm; DFLLMUL = 1464; DFLLVAL after Reset; DFLLCTRL.BPLCKC = 1; DFLLCTRL.QLDIS = 0; DFLLCTRL.CCDIS = 1; DFLLMUL.FSTEP = 10typ 429 · max 1145 us1817
Current Consumption IDDOpen Loop mode - DFLLVAL after reset; VDD = 3.3V; typ. 25°C, max. 85°Ctyp 404 · max 854 uA1817
Current Consumption IDDClosed Loop mode - fREF = 32 .768 kHz; VDD = 3.3V; typ. 25°C, max. 85°Ctyp 404 · max 854 uA1817
Input Frequency fINLDO regulator and direct reference XOSC or XOSC32Kmin 32 · max 3200 kHz1817
Output Frequency fOUTLDO regulator and direct reference XOSC or XOSC32Kmin 96 · max 200 MHz1817
Period jitter (Peak-Peak value) JpfIN = 32 kHz, fOUT = 96 MHz; LDO regulator and direct referencetyp 1.9 · max 2.7 %1817
Period jitter (Peak-Peak value) JpfIN = 32 kHz, fOUT = 200 MHz; LDO regulator and direct referencetyp 3.4 · max 4.9 %1817
Period jitter (Peak-Peak value) JpfIN = 3.2 MHz, fOUT = 96 MHz; LDO regulator and direct referencetyp 2 · max 3 %1817
Period jitter (Peak-Peak value) JpfIN = 3.2 MHz, fOUT = 200 MHz; LDO regulator and direct referencetyp 4.3 · max 6.6 %1817
Lock Time tLOCKAfter startup, time to get lock signal; fIN = 3.2 MHz; LDO regulator and direct referencetyp 54 · max 95 us1817
Duty cycle DutyLDO regulator and direct referencetyp 50 %1817
Current Consumption IDDClk = 96 MHz, VDD = 3.3V; typ. 25°C, max. 85°Ctyp 0.9 · max 1.3 mA1817
Current Consumption IDDClk = 200 MHz, VDD = 3.3V; typ. 25°C, max. 85°Ctyp 2 · max 2.3 mA1817
Active / Idle IDDVDD = 1.8V; typ. 25°C, max. 105°Ctyp 8.52 · max 13.26 uA1841
Active / Idle IDDVDD = 3.3V; typ. 25°C, max. 105°Ctyp 10.1 · max 15.7 uA1841
Standby with BOD continuous normal mode IDDVDD = 1.8V; typ. 25°C, max. 105°Ctyp 4.71 · max 6.74 uA1841
Standby with BOD continuous normal mode IDDVDD = 3.3V; typ. 25°C, max. 105°Ctyp 6.01 · max 8.59 uA1841
Standby with BOD continuous low power mode or Hibernate mode IDDVDD = 1.8V; typ. 25°C, max. 105°Ctyp 0.15 · max 0.25 uA1841
Standby with BOD continuous low power mode or Hibernate mode IDDVDD = 3.3V; typ. 25°C, max. 105°Ctyp 0.21 · max 0.33 uA1841
ADC Reference Voltage VREFInternal or External Reference VREF ≤ VDDANA - 0.4V; Max. VDDANA-0.4min 1 V1841
Input common mode voltage VCMCTRLA.R2R =1; Max. VDDANAmin 0 V1841
ADC stabilization Time TSETTINGCTRLA.ENABLE=1 or CTRLA.ONEDEMAND=1typ 10 us1841
ADC Clock Period TADVDDIO=VDDANA 1.71V to 3.63V; -40°C ≤ TA ≤ +105°Cmin 62.5 · max 3125 ns1841
ADCx Module GCLK max input freq fGCLK_ADCxVDDIO=VDDANA 1.71V to 3.63V; -40°C ≤ TA ≤ +105°Cmax 100 MHz1841
ADC Sample Time TSAMP-40°C ≤ TA ≤ +105°C; TAD(min) Ext Analog Input Rsource ≤ 147 Ωmin 1 TAD1843
ADC Sample Time TSAMP-40°C ≤ TA ≤ +105°C; TAD(min), Ext Analog Input Rsource ≤ 2,250 Ωmin 2 TAD1843
ADC Sample Time TSAMP-40°C ≤ TA ≤ +105°C; TAD(min), Ext Analog Input Rsource ≤ 4,400 Ωmin 3 TAD1843
ADC Sample Time TSAMP-40°C ≤ TA ≤ +105°C; TAD(min), Ext Analog Input Rsource ≤ 6,550 Ωmin 4 TAD1843
ADC Sample Time TSAMP-40°C ≤ TA ≤ +105°C; TAD(min), Ext Analog Input Rsource ≤ 8,700 Ωmin 5 TAD1843
ADC Sample Time TSAMP-40°C ≤ TA ≤ +105°C; TAD(min), Ext Analog Input Rsource ≤ 10,850 Ωmin 6 TAD1843
ADC Sample Time TSAMPSample time with Temp sensor or band gap as input; -40°C ≤ TA ≤ +105°Cmin 10000 ns1843
Conversion Time (3) (Single-Ended Mode) TCNV12-bit resolution; -40°C ≤ TA ≤ +105°Ctyp 12 TAD1843
Conversion Time (3) (Single-Ended Mode) TCNV10-bit resolution; -40°C ≤ TA ≤ +105°Ctyp 11 TAD1843
Conversion Time (3) (Single-Ended Mode) TCNV8-bit resolution; -40°C ≤ TA ≤ +105°Ctyp 9 TAD1843
Conversion Time (3) (Differential Mode) TCNV12-bit resolution; -40°C ≤ TA ≤ +105°Ctyp 12 TAD1843
Conversion Time (3) (Differential Mode) TCNV10-bit resolution; -40°C ≤ TA ≤ +105°Ctyp 10 TAD1843
Conversion Time (3) (Differential Mode) TCNV8-bit resolution; -40°C ≤ TA ≤ +105°Ctyp 8 TAD1843
ADC Internal Sample Cap CSAMPLE-40°C ≤ TA ≤ +105°Cmin 2 · max 3 pf1843
ADC Internal impedance RSAMPLE-40°C ≤ TA ≤ +105°Cmax 2000 Ω1843
Resolution ResSelectable 8, 10, 12 bit Resolution Ranges; table states -40°C ≤ TA ≤ +85°Cmin 8 · max 12 bits1843
Effective Number of bits EN0B1msps, R2R disabled, VREF = VDDANA = VDDIO = 3.0; table states -40°C ≤ TA ≤ +85°Cmin 10.5 bits1843
Effective Number of bits EN0B1msps, R2R disabled, External VREF = 2.0V, VDDANA = VDDIO = 3.0; table states -40°C ≤ TA ≤ +85°Cmin 10.5 bits1843
Differential mode IDD VDDANAfs = 1 Msps; reference buffer disabled; BIASREFBUF = '111'; BIASREFCOMP = '111'; VDDANA = VREF = 3.0V; typ. 25°C, max. 105°Ctyp 279 · max 326 uA1846
Differential mode IDD VDDANAfs = 1 Msps; reference buffer enabled; BIASREFBUF = '111'; BIASREFCOMP = '111'; VDDANA = VREF = 3.0V; typ. 25°C, max. 105°Ctyp 482 · max 686 uA1846
Differential mode IDD VDDANAfs = 10 ksps; reference buffer disabled; BIASREFBUF = '111'; BIASREFCOMP = '111'; VDDANA = VREF = 3.0V; typ. 25°C, max. 105°Ctyp 28 · max 85 uA1846
Differential mode IDD VDDANAfs = 10 ksps; reference buffer enabled; BIASREFBUF = '111'; BIASREFCOMP = '111'; VDDANA = VREF = 3.0V; typ. 25°C, max. 105°Ctyp 241 · max 435 uA1846
Single Ended mode IDD VDDANAfs = 1 Msps; reference buffer disabled; BIASREFBUF = '111'; BIASREFCOMP = '111'; VDDANA = VREF = 3.0V; typ. 25°C, max. 105°Ctyp 307 · max 361 uA1846
Single Ended mode IDD VDDANAfs = 1 Msps; reference buffer enabled; BIASREFBUF = '111'; BIASREFCOMP = '111'; VDDANA = VREF = 3.0V; typ. 25°C, max. 105°Ctyp 499 · max 730 uA1846
Single Ended mode IDD VDDANAfs = 10 ksps; reference buffer disabled; BIASREFBUF = '111'; BIASREFCOMP = '111'; VDDANA = VREF = 3.0V; typ. 25°C, max. 105°Ctyp 38 · max 126 uA1846
Single Ended mode IDD VDDANAfs = 10 ksps; reference buffer enabled; BIASREFBUF = '111'; BIASREFCOMP = '111'; VDDANA = VREF = 3.0V; typ. 25°C, max. 105°Ctyp 245 · max 448 uA1846
Effective Number Of Bits ENOBFs = 1 Ms/s - External Ref - CCTRL = 0x2min 9.7 · typ 10.7 · max 11 Bits1846
Signal to Noise ratio SNRFs = 1 Ms/s - External Ref - CCTRL = 0x2min 61.3 · typ 68.6 · max 74.5 dB1846
Total Harmonic Distortion THDFs = 1 Ms/s - External Ref - CCTRL = 0x2min -82.3 · typ -72.5 · max -58.9 dB1846
Integral Non Linearity, Best Fit curve from 0x080 to 0xF7F INL105°C; i12clk=12 MHz; VDDANA = 3.0V; External Ref = 2.0V; Cload = 50pFtyp 2.7 · max 4 LSB1847
Integral Non Linearity, Best Fit curve from 0x080 to 0xF7F INL105°C; i12clk=12 MHz; VDDANA = 3.0V; 1V Internal Ref; Cload = 50pFtyp 5.2 · max 8.7 LSB1847
Differential Non Linearity, Best Fit curve from 0x080 to 0xF7F DNL105°C; i12clk=12 MHz; VDDANA = 3.0V; External Ref = 2.0V; Cload = 50pFtyp 3.5 · max 6.1 LSB1847
Differential Non Linearity, Best Fit curve from 0x080 to 0xF7F DNL105°C; i12clk=12 MHz; VDDANA = 3.0V; 1V Internal Ref; Cload = 50pFtyp 6.4 · max 9.4 LSB1847
Gain Error Gerr105°C; External Reference voltagetyp 0.3 · max 1.6 % FSR1847
Gain Error Gerr105°C; 1.0V Internal Reference voltagetyp 0.8 · max 8.6 % FSR1847
Offset Error Offerr105°C; External Reference voltagetyp 7 · max 25 mV1847
Offset Error Offerr105°C; 1.0V Internal Reference voltagetyp 2 · max 19 mV1847
Effective Number of Bits ENOB105°C; Fs = 1 Ms/s; External Ref; CCTRL = 0x2min 9.1 · typ 10.3 · max 10.8 Bits1847
Signal to Noise Ratio SNR105°C; Fs = 1 Ms/s - External Ref - CCTRL = 0x2min 63.5 · typ 68.6 · max 74.5 dB1847
Total Harmonic Distortion THD105°C; Fs = 1 Ms/s; External Ref; CCTRL = 0x2min -82.3 · typ -72.8 · max -61 dB1847
Differential Mode, DC supply current, 2 output channels - without load IDDANAfs = 1 Msps, CCTR L= 0x2, VREF > 2.4V, VDD = 3.3V; Max. 105°C, Typ. 25°Ctyp 384 · max 593 uA1847
Differential Mode, DC supply current, 2 output channels - without load IDDANAfs = 10 ksps, CCTRL = 0x0, VREF < 2.4V, VDD= 3.3V; Max. 105°C, Typ. 25°Ctyp 283 · max 457 uA1847
Single-Ended Mode, DC supply current, 2 output channels - without load IDDANAfs = 1 Msps, CCTRL = 0x2, VREF > 2.4V, VDD = 3.3V; Max. 105°C, Typ. 25°Ctyp 306 · max 493 uA1847
Single-Ended Mode, DC supply current, 2 output channels - without load IDDANAfs = 10 ksps, CCTRL = 0x0, VREF < 2.4V, VDD = 3.3V; Max. 105°C, Typ. 25°Ctyp 230 · max 369 uA1847
Offset Off105°C; High speed COMPCTRLn.SPEED = 0x3; Hysteresis disabledmin -22 · typ 3 · max 22 mV1847
Propagation Delay Tpd105°C; Vcm=VDDANA/2, Vin = +/-100mV overdrive from Vcm; High speed COMPCTRLn.SPEED = 0x3typ 24.1 · max 42 ns1847
Startup time Tstart105°C; High speed COMPCTRLn.SPEED = 0x3typ 4.7 · max 8 us1847
Current consumption for One AC enabled, Hysteresis disabled voltage scaler disabled IDDANACOMPCTRLn.SPEED=0x3, VDDANA=3.3V; Max.105°C, Typ.25°Ctyp 59 · max 103 uA1848
Current consumption Voltage Scaler only IDDANAVDDANA=3.3V; Max.105°C, Typ.25°Ctyp 11 · max 18 uA1848
Current Consumption IDDPTC scan rate 10 msec; 4 oversamples; Max 105°C, Typ 25°C; VDD = 3.0V; CPU 48MHz; PTC 4MHz; mutual-capacitance, one touch channel; standby sleeptyp 137 · max 2174 uA1848
Current Consumption IDDPTC scan rate 10 msec; 16 oversamples; Max 105°C, Typ 25°C; VDD = 3.0V; CPU 48MHz; PTC 4MHz; mutual-capacitance, one touch channel; standby sleeptyp 146 · max 2194 uA1848
Current Consumption IDDPTC scan rate 50 msec; 4 oversamples; Max 105°C, Typ 25°C; VDD = 3.0V; CPU 48MHz; PTC 4MHz; mutual-capacitance, one touch channel; standby sleeptyp 77 · max 2098 uA1848
Current Consumption IDDPTC scan rate 50 msec; 16 oversamples; Max 105°C, Typ 25°C; VDD = 3.0V; CPU 48MHz; PTC 4MHz; mutual-capacitance, one touch channel; standby sleeptyp 79 · max 2104 uA1848
Current Consumption IDDPTC scan rate 100 msec; 4 oversamples; Max 105°C, Typ 25°C; VDD = 3.0V; CPU 48MHz; PTC 4MHz; mutual-capacitance, one touch channel; standby sleeptyp 68 · max 2092 uA1848
Current Consumption IDDPTC scan rate 100 msec; 16 oversamples; Max 105°C, Typ 25°C; VDD = 3.0V; CPU 48MHz; PTC 4MHz; mutual-capacitance, one touch channel; standby sleeptyp 69 · max 2095 uA1848
Current Consumption IDDPTC scan rate 200 msec; 4 oversamples; Max 105°C, Typ 25°C; VDD = 3.0V; CPU 48MHz; PTC 4MHz; mutual-capacitance, one touch channel; standby sleeptyp 64 · max 2086 uA1848
Current Consumption IDDPTC scan rate 200 msec; 16 oversamples; Max 105°C, Typ 25°C; VDD = 3.0V; CPU 48MHz; PTC 4MHz; mutual-capacitance, one touch channel; standby sleeptyp 65 · max 2089 uA1848
CPU FMax (MHz)105°C; 0 WS; VDD > 1.71max 19 MHz1849
CPU FMax (MHz)105°C; 1 WS; VDD > 1.71max 38 MHz1849
CPU FMax (MHz)105°C; 2 WS; VDD > 1.71max 57 MHz1849
CPU FMax (MHz)105°C; 3 WS; VDD > 1.71max 76 MHz1849
CPU FMax (MHz)105°C; 4 WS; VDD > 1.71max 95 MHz1849
CPU FMax (MHz)105°C; 5 WS; VDD > 1.71max 100 MHz1849
CPU FMax (MHz)105°C; 6 WS; VDD > 1.71max 120 MHz1849
CPU FMax (MHz)105°C; Auto WS; VDD > 1.71max 120 MHz1849
Current Consumption IDDXOSC; F = 8 MHz - CL = 20 pF - IMULT = 0x3, ENALC = OFF; Max. 105°C, Typ. 25°Ctyp 0.43 · max 1.56 mA1849
Current Consumption IDDXOSC; F = 8 MHz - CL = 20 pF - IMULT = 0x3, ENALC = ON; Max. 105°C, Typ. 25°Ctyp 0.16 · max 1.16 mA1849
Current Consumption IDDXOSC; F = 16 MHz - CL = 20 pF - IMULT = 0x5, ENALC = OFF; Max. 105°C, Typ. 25°Ctyp 1.31 · max 3.23 mA1849
Current Consumption IDDXOSC; F = 16 MHz - CL = 20 pF - IMULT = 0x5, ENALC = ON; Max. 105°C, Typ. 25°Ctyp 0.25 · max 1.33 mA1849
Current Consumption IDDXOSC; F = 32 MHz - CL = 13 pF - IMULT = 0x5, ENALC = OFF; Max. 105°C, Typ. 25°Ctyp 2.92 · max 5.74 mA1849
Current Consumption IDDXOSC; F = 32 MHz - CL = 13 pF - IMULT = 0x5, ENALC = ON; Max. 105°C, Typ. 25°Ctyp 0.4 · max 1.92 mA1849
Current Consumption IDDXOSC; F = 48 MHz - CL = 13 pF - IMULT = 0x6, ENALC = OFF; Max. 105°C, Typ. 25°Ctyp 2.7 · max 5.82 mA1849
Current Consumption IDDXOSC; F = 48 MHz - CL = 13 pF - IMULT = 0x6, ENALC = ON; Max. 105°C, Typ. 25°Ctyp 0.76 · max 2.64 mA1849
Current consumption IDDXOSC32K; VDD=3.0V; Std. gain; Max 105°C, Typ 25°Ctyp 1.5 · max 2.5 uA1849
Current consumption IDDXOSC32K; VDD=3.0V; High gain; Max 105°C, Typ 25°Ctyp 1.9 · max 3.3 uA1849
Output frequency FOUT[-40, +105]°C, VDDANA>1.71Vmin 26 · typ 32.768 · max 39.5 kHz1849
Output frequency FOpenOUTDFLLVAL after Reset; LDO Regulator mode, [-40, 105]°Cmin 45.57 · typ 48 · max 50.09 MHz1850
Output frequency FOpenOUTDFLLVAL after Reset; LDO Regulator mode, [0, 60]°Cmin 47.12 · typ 48 · max 48.9 MHz1850
Startup time TOpenSTARTUPDFLLVAL after Reset; FOUT within 90% of final valuetyp 4.3 · max 6.5 us1850
Current Consumption IDDOpen Loop mode - DFLLVAL after reset VDD = 3.3V; Max. 105°C, Typ. 25°Ctyp 400 · max 1400 uA1850
Current Consumption IDDClosed Loop mode - fREF = 32 .768 kHz VDD = 3.3V; Max. 105°C, Typ. 25°Ctyp 404 · max 1390 uA1850
Period jitter (Peak-Peak value) Jp105°C; fIN = 32 kHz, fOUT = 96 MHz; LDO regulator, direct referencetyp 1.9 · max 2.9 %1850
Period jitter (Peak-Peak value) Jp105°C; fIN = 32 kHz, fOUT = 200 MHz; LDO regulator, direct referencetyp 3.4 · max 5.6 %1850
Period jitter (Peak-Peak value) Jp105°C; fIN = 3.2 MHz, fOUT = 96 MHz; LDO regulator, direct referencetyp 2 · max 3.1 %1850
Period jitter (Peak-Peak value) Jp105°C; fIN = 3.2 MHz, fOUT = 200 MHz; LDO regulator, direct referencetyp 4.3 · max 7.1 %1850
Duty cycle Duty105°C; based on simulationtyp 50 %1850
Current Consumption IDDCk = 96 MHz, VDD = 3.3V; Max. 105°C, Typ. 25°Ctyp 0.9 · max 1.8 mA1850
Current Consumption IDDCk = 200 MHz, VDD = 3.3V; Max. 105°C, Typ. 25°Ctyp 2 · max 2.6 mA1850
Input Low Injection Current IICL125°C; all pins; VIL source < (VSS - 0.6)min -15 mA1851
Input High Injection Current IICH125°C; all I/O pins; VIH source > (VDDIO + 0.6)max 15 mA1851
Total Input Injection Current (Sum of all I/O and control pins) Absolute value of |∑IICT| ∑IICT125°C; absolute instantaneous sum of all ± input injection currents from all I/O pinsmax 18 mA1851
CPU clock frequency fCPU125°Cmax 100 MHz1851
AHB clock frequency fAHB125°Cmax 100 MHz1851
APBA, APBB, APBC and APBD clock frequency fAPBx, x = {A, B, C, D}125°Cmax 100 MHz1851
EIC input clock frequency fGCLK_EIC125°Cmax 90 MHz1851
FREQM Measure fGCLK_FREQM_MSR125°Cmax 180 MHz1851
Active / Idle IDDVDD = 1.8V; Max 125°C Typ 25°Ctyp 8.52 · max 13.9 uA1858
Active / Idle IDDVDD = 3.3V; Max 125°C Typ 25°Ctyp 10.1 · max 16.5 uA1858
Standby with BOD continuous normal mode IDDVDD = 1.8V; Max 125°C Typ 25°Ctyp 4.71 · max 6.7 uA1858
Standby with BOD continuous normal mode IDDVDD = 3.3V; Max 125°C Typ 25°Ctyp 6.01 · max 8.6 uA1858
Standby with BOD continuous low power mode or Hibernate mode IDDVDD = 1.8V; Max 125°C Typ 25°Ctyp 0.15 · max 0.27 uA1858
Standby with BOD continuous low power mode or Hibernate mode IDDVDD = 3.3V; Max 125°C Typ 25°Ctyp 0.21 · max 0.35 uA1858
ADC Reference Voltage VREFInternal or External Reference VREF ≤ VDDANA - 0.4V; maximum VDDANA-0.4; -40°C ≤ TA ≤ +125°Cmin 1 V1858
Input common mode voltage VCMCTRLA.R2R =1; maximum VDDANA; -40°C ≤ TA ≤ +125°Cmin 0 V1858
ADC stabilization Time TSETTINGCTRLA.ENABLE=1 or CTRLA.ONEDEMAND=1; -40°C ≤ TA ≤ +125°Ctyp 10 us1858
ADC Clock Period TADVDDIO=VDDANA 1.71V to 3.63V; -40°C ≤ TA ≤ +125°Cmin 62.5 · max 3125 ns1858
ADCx Module GCLK max input freq fGCLK_ADCxVDDIO=VDDANA 1.71V to 3.63V; -40°C ≤ TA ≤ +125°Cmax 100 MHz1858
ADC Internal Sample Cap CSAMPLEVDDIO=VDDANA 1.71V to 3.63V; -40°C ≤ TA ≤ +125°Cmin 2 · max 3 pf1860
ADC Internal impedance RSAMPLEVDDIO=VDDANA 1.71V to 3.63V; -40°C ≤ TA ≤ +125°Cmax 2000 Ω1860
Resolution ResSelectable 8, 10, 12 bit Resolution Ranges; -40°C ≤ TA ≤ +125°Cmin 8 · max 12 bits1860
Effective Number of bits EN0B1msps, R2R disabled, VREF = VDDANA = VDDIO = 3.0; -40°C ≤ TA ≤ +125°Cmin 10.5 bits1860
Effective Number of bits EN0B1msps, R2R disabled, External VREF = 2.0V, VDDANA = VDDIO = 3.0; -40°C ≤ TA ≤ +125°Cmin 10.5 bits1860
Integral Nonlinearity INL1msps, R2R disabled, VREF = VDDANA = VDDIO = 3.0; -40°C ≤ TA ≤ +125°Cmin -1.8 · max 1.8 LSb1860
Integral Nonlinearity INL1msps, R2R disabled, External VREF = 2.0V, VDDANA = VDDIO = 3.0; -40°C ≤ TA ≤ +125°Cmin -1.9 · max 1.9 LSb1860
Differential Nonlinearity DNL1msps, R2R disabled,VREF = VDDANA = VDDIO = 3.0; -40°C ≤ TA ≤ +125°Cmin -1 · max 1 LSb1860
Differential Nonlinearity DNL1msps, R2R disabled, External VREF = 2.0V, VDDANA = VDDIO = 3.0; -40°C ≤ TA ≤ +125°Cmin -1 · max 1.2 LSb1860
Gain Error with REFCTRL.REFCOMP=1 GERR1msps, VREF = VDDANA = VDDIO = 3.0; -40°C ≤ TA ≤ +125°Cmin -0.21 · max 0.2 %FSR1860
Gain Error with REFCTRL.REFCOMP=1 GERR1msps, External VREF = 2.0V, VDDANA = VDDIO = 3.0; -40°C ≤ TA ≤ +125°Cmin -0.13 · max 0.21 %FSR1860
Gain Error with REFCTRL.REFCOMP=1 GERR1msps, VREF=1V Internal band gap, VDDANA = VDDIO = 3.0; -40°C ≤ TA ≤ +125°Cmin -10 · max 6.7 %FSR1860
Gain Error with REFCTRL.REFCOMP=1 GERR1msps, VREF = VDDANA/2, VDDANA = VDDIO = 3.0; -40°C ≤ TA ≤ +125°Cmin -0.48 · max 0.75 %FSR1860
Gain Error with REFCTRL.REFCOMP=0 GERR1msps, VREF = VDDANA = VDDIO = 3.0; -40°C ≤ TA ≤ +125°Cmin -0.3 · max 0.2 %FSR1860
Gain Error with REFCTRL.REFCOMP=0 GERR1msps, External VREF = 2.0V, VDDANA = VDDIO = 3.0; -40°C ≤ TA ≤ +125°Cmin -0.94 · max 0.71 %FSR1860
Gain Error with REFCTRL.REFCOMP=0 GERR1msps, VREF=1V Internal band gap, VDDANA = VDDIO = 3.0; -40°C ≤ TA ≤ +125°Cmin -10 · max 6.7 %FSR1860
Gain Error with REFCTRL.REFCOMP=0 GERR1msps, VREF = VDDANA/2, VDDANA = VDDIO = 3.0; -40°C ≤ TA ≤ +125°Cmin -1.2 · max 1.28 %FSR1860
Differential mode IDD VDDANAfs = 1 Msps / Reference buffer disabled / BIASREFBUF = '111', BIASREFCOMP = '111'; VDDANA = VREF = 3.0V; Max 125°C, Typ 25°Ctyp 279 · max 848 uA1863
Differential mode IDD VDDANAfs = 1 Msps / Reference buffer enabled / BIASREFBUF = '111', BIASREFCOMP = '111'; VDDANA = VREF = 3.0V; Max 125°C, Typ 25°Ctyp 482 · max 1381 uA1863
Differential mode IDD VDDANAfs = 10 ksps / Reference buffer disabled / BIASREFBUF = '111', BIASREFCOMP = '111'; VDDANA = VREF = 3.0V; Max 125°C, Typ 25°Ctyp 28 · max 91 uA1863
Differential mode IDD VDDANAfs = 10 ksps / Reference buffer enabled / BIASREFBUF = '111', BIASREFCOMP = '111'; VDDANA = VREF = 3.0V; Max 125°C, Typ 25°Ctyp 241 · max 807 uA1863
Single Ended mode IDD VDDANAfs = 1 Msps / Reference buffer disabled / BIASREFBUF = '111', BIASREFCOMP = '111'; VDDANA = VREF = 3.0V; Max 125°C, Typ 25°Ctyp 307 · max 820 uA1863
Single Ended mode IDD VDDANAfs = 1 Msps / Reference buffer enabled / BIASREFBUF = '111', BIASREFCOMP = '111'; VDDANA = VREF = 3.0V; Max 125°C, Typ 25°Ctyp 499 · max 1156 uA1863
Single Ended mode IDD VDDANAfs = 10 ksps / Reference buffer disabled / BIASREFBUF = '111', BIASREFCOMP = '111'; VDDANA = VREF = 3.0V; Max 125°C, Typ 25°Ctyp 38 · max 108 uA1863
Single Ended mode IDD VDDANAfs = 10 ksps / Reference buffer enabled / BIASREFBUF = '111', BIASREFCOMP = '111'; VDDANA = VREF = 3.0V; Max 125°C, Typ 25°Ctyp 245 · max 881 uA1863
Integral Non Linearity, Best-fit curve from 0x080 to 0xF7F INL125°C; i12clk = 12 MHz, VDDANA = 3.0V, External Ref. = 2.0V, CLOAD = 50 pFtyp 2.4 · max 4.1 LSB1863
Integral Non Linearity, Best-fit curve from 0x080 to 0xF7F INL125°C; i12clk = 12 MHz, VDDANA = 3.0V, Internal Ref, CLOAD = 50 pFtyp 3.2 · max 4.2 LSB1863
Differential Non Linearity, Best-fit curve from 0x080 to 0xF7F DNL125°C; i12clk = 12 MHz, VDDANA = 3.0V, External Ref. = 2.0V, CLOAD = 50 pFtyp 2.4 · max 4.5 LSB1863
Differential Non Linearity, Best-fit curve from 0x080 to 0xF7F DNL125°C; i12clk = 12 MHz, VDDANA = 3.0V, Internal Ref, CLOAD = 50 pFtyp 3.5 · max 5.4 LSB1863
Gain Error Gerr125°C; External Reference voltagetyp 0.4 · max 1.9 % FSR1863
Gain Error Gerr125°C; 1.0V Internal Reference voltagetyp 0.8 · max 8.5 % FSR1863
Offset Error Offerr125°C; External Reference voltagetyp 13 · max 47 mV1863
Offset Error Offerr125°C; 1.0V Internal Reference voltagetyp 8 · max 79 mV1863
Effective Number of Bits ENOB125°C; Fs = 1Ms/s - External Ref - CCTRL=0x2min 9.9 · typ 10.7 · max 10.91863
Signal to Noise ratio SNR125°C; Fs = 1Ms/s - External Ref - CCTRL=0x2min 63.5 · typ 68.6 · max 72.6 dB1863
Total Harmonic Distortion THD125°C; Fs = 1Ms/s - External Ref - CCTRL=0x2min -79.1 · typ -72.5 · max -61 dB1863
Integral Non Linearity, Best-fit curve from 0x080 to 0xF7F INL125°C; i12clk = 12 MHz, VDDANA = 3.0V External Ref. = 2.0V, CLOAD = 50 pFtyp 2.7 · max 6 LSB1864
Integral Non Linearity, Best-fit curve from 0x080 to 0xF7F INL125°C; i12clk = 12 MHz, VDDANA = 3.0V, Internal Ref, CLOAD = 50 pFtyp 5.2 · max 11.2 LSB1864
Differential Non Linearity, Best-fit curve from 0x080 to 0xF7F DNL125°C; i12clk = 12 MHz, VDDANA = 3.0V External Ref = 2.0V, CLOAD = 50 pFtyp 3.5 · max 8.1 LSB1864
Differential Non Linearity, Best-fit curve from 0x080 to 0xF7F DNL125°C; i12clk = 12 MHz, VDDANA = 3.0V, Internal Ref, CLOAD = 50 pFtyp 6.4 · max 12.1 LSB1864
Gain Error Gerr125°C; External Reference voltagetyp 0.3 · max 1.6 % FSR1864
Gain Error Gerr125°C; 1.0V Internal Reference voltagetyp 0.8 · max 8.6 % FSR1864
Offset Error Offerr125°C; External Reference voltagetyp 7 · max 25.5 mV1864
Offset Error Offerr125°C; 1.0V Internal Reference voltagetyp 2 · max 19 mV1864
Effective Number of Bits ENOB125°C; Fs = 1Ms/s - External Ref - CCTRL=0x2min 9.1 · typ 10.3 · max 10.71864
Total Harmonic Distortion THD125°C; Fs = 1Ms/s - External Ref - CCTRL=0x2min -79.1 · typ -72.8 · max -61 dB1864
Differential Mode, DC supply current, 2 output channels - without load IDDANAfs = 1 Msps, CCTR L= 0x2, VREF > 2.4V, VDD= 3.3V; Max. 125°C, Typ. 25°Ctyp 384 · max 634 uA1864
Differential Mode, DC supply current, 2 output channels - without load IDDANAfs = 10 ksps, CCTRL = 0x0, VREF < 2.4V, VDD= 3.3V; Max. 125°C, Typ. 25°Ctyp 283 · max 482 uA1864
Single-Ended Mode, DC supply current, 2 output channels - without load IDDANAfs = 1 Msps, CCTRL = 0x2, VREF > 2.4V, VDD = 3.3V; Max. 125°C, Typ. 25°Ctyp 306 · max 517 uA1864
Single-Ended Mode, DC supply current, 2 output channels - without load IDDANAfs = 10 ksps, CCTRL = 0x0, VREF < 2.4V, VDD = 3.3V; Max. 125°C, Typ. 25°Ctyp 230 · max 389 uA1864
Offset Off125°C; High-speed COMPCTRLn.SPEED = 0x3; Hysteresis disabledmin -22 · typ 3 · max 22 mV1864
Propagation Delay Tpd125°C; Vcm=VDDANA/2, Vin = +/-100mV overdrive from Vcm; High- speed COMPCTRLn.SPEED = 0x3typ 24.1 · max 42 ns1864
Startup time Tstart125°C; High- speed COMPCTRLn.SPEED = 0x3typ 4.7 · max 8 us1864
Current consumption for One AC enabled, Hysteresis disabled voltage scaler disabled IDDANACOMPCTRLn.SPEED = 0x3, VDDANA = 3.3V; Max.125°C, Typ.25°Ctyp 59 · max 106 uA1865
Current consumption Voltage Scaler only IDDANAVDDANA=3.3V; Max.125°C, Typ.25°Ctyp 11 · max 23.3 uA1865
Current Consumption IDDPTC scan rate 10 msec; 4 oversamples; Max. 125°C, Typ 25°C; VDD = 3.0V; CPU 48 MHz; PTC 4 MHz; Mutual Capacitance mode; one touch channel; Standby Sleeptyp 137 · max 3960 uA1865
Current Consumption IDDPTC scan rate 10 msec; 16 oversamples; Max. 125°C, Typ 25°C; VDD = 3.0V; CPU 48 MHz; PTC 4 MHz; Mutual Capacitance mode; one touch channel; Standby Sleeptyp 146 · max 3989 uA1865
Current Consumption IDDPTC scan rate 50 msec; 4 oversamples; Max. 125°C, Typ 25°C; VDD = 3.0V; CPU 48 MHz; PTC 4 MHz; Mutual Capacitance mode; one touch channel; Standby Sleeptyp 77 · max 3882 uA1865
Current Consumption IDDPTC scan rate 50 msec; 16 oversamples; Max. 125°C, Typ 25°C; VDD = 3.0V; CPU 48 MHz; PTC 4 MHz; Mutual Capacitance mode; one touch channel; Standby Sleeptyp 79 · max 3893 uA1865
Current Consumption IDDPTC scan rate 100 msec; 4 oversamples; Max. 125°C, Typ 25°C; VDD = 3.0V; CPU 48 MHz; PTC 4 MHz; Mutual Capacitance mode; one touch channel; Standby Sleeptyp 68 · max 3877 uA1865
Current Consumption IDDPTC scan rate 100 msec; 16 oversamples; Max. 125°C, Typ 25°C; VDD = 3.0V; CPU 48 MHz; PTC 4 MHz; Mutual Capacitance mode; one touch channel; Standby Sleeptyp 69 · max 3885 uA1865
Current Consumption IDDPTC scan rate 200 msec; 4 oversamples; Max. 125°C, Typ 25°C; VDD = 3.0V; CPU 48 MHz; PTC 4 MHz; Mutual Capacitance mode; one touch channel; Standby Sleeptyp 64 · max 3870 uA1865
Current Consumption IDDPTC scan rate 200 msec; 16 oversamples; Max. 125°C, Typ 25°C; VDD = 3.0V; CPU 48 MHz; PTC 4 MHz; Mutual Capacitance mode; one touch channel; Standby Sleeptyp 65 · max 3872 uA1865
CPU FMax (MHz)125°C; 0 WS; VDD > 1.71max 19 MHz1866
CPU FMax (MHz)125°C; 1 WS; VDD > 1.71max 38 MHz1866
CPU FMax (MHz)125°C; 2 WS; VDD > 1.71max 57 MHz1866
CPU FMax (MHz)125°C; 3 WS; VDD > 1.71max 76 MHz1866
CPU FMax (MHz)125°C; 4 WS; VDD > 1.71max 95 MHz1866
CPU FMax (MHz)125°C; 5 WS; VDD > 1.71max 100 MHz1866
CPU FMax (MHz)125°C; 6 WS; VDD > 1.71max 100 MHz1866
CPU FMax (MHz)125°C; Auto WS; VDD > 1.71max 100 MHz1866
Current Consumption IDDXOSC; F = 8 MHz - CL = 20 pF - IMULT = 0x3, ENALC = OFF; Max. 125°C, Typ. 25°Ctyp 0.43 · max 2.27 mA1866
Current Consumption IDDXOSC; F = 8 MHz - CL = 20 pF - IMULT = 0x3, ENALC = ON; Max. 125°C, Typ. 25°Ctyp 0.16 · max 1.87 mA1866
Current Consumption IDDXOSC; F = 16 MHz - CL = 20 pF - IMULT = 0x5, ENALC = OFF; Max. 125°C, Typ. 25°Ctyp 1.31 · max 3.72 mA1866
Current Consumption IDDXOSC; F = 16 MHz - CL = 20 pF - IMULT = 0x5, ENALC = ON; Max. 125°C, Typ. 25°Ctyp 0.25 · max 2.23 mA1866
Current Consumption IDDXOSC; F = 32 MHz - CL = 13 pF - IMULT = 0x5, ENALC = OFF; Max. 125°C, Typ. 25°Ctyp 2.92 · max 6.49 mA1866
Current Consumption IDDXOSC; F = 32 MHz - CL = 13 pF - IMULT = 0x5, ENALC = ON; Max. 125°C, Typ. 25°Ctyp 0.4 · max 2.43 mA1866
Current Consumption IDDXOSC; F = 48 MHz - CL = 13 pF - IMULT = 0x6, ENALC = OFF; Max. 125°C, Typ. 25°Ctyp 2.7 · max 6.71 mA1866
Current Consumption IDDXOSC; F = 48 MHz - CL = 13 pF - IMULT = 0x6, ENALC = ON; Max. 125°C, Typ. 25°Ctyp 0.76 · max 3.52 mA1866
Current consumption IDDXOSC32K; VDD=3.0V; Std. gain; Max 125°C, Typ 25°Ctyp 1.5 · max 2.6 uA1866
Current consumption IDDXOSC32K; VDD=3.0V; High gain; Max 125°C, Typ 25°Ctyp 1.9 · max 3.4 uA1866
Output frequency FOUT[-40, +125]°C, VDDANA>1.71Vmin 26 · typ 32.768 · max 40.92 kHz1866
Output frequency FOpenOUTDFLLVAL after Reset; LDO Regulator mode, [-40, 125]°Cmin 45.57 · typ 48 · max 50.63 MHz1867
Current Consumption IDDOpen Loop mode - DFLLVAL after reset VDD = 3.3V; Max. 125°C, Typ. 25°Ctyp 400 · max 2129 uA1867
Current Consumption IDDClosed Loop mode - fREF = 32 .768 kHz VDD = 3.3V; Max. 125°C, Typ. 25°Ctyp 404 · max 2113 uA1867
Period jitter (Peak-Peak value) Jp125°C; fIN = 32 kHz, fOUT = 96 MHz; LDO regulator, direct referencetyp 1.9 · max 3 %1867
Period jitter (Peak-Peak value) Jp125°C; fIN = 32 kHz, fOUT = 200 MHz; LDO regulator, direct referencetyp 3.4 · max 6 %1867
Period jitter (Peak-Peak value) Jp125°C; fIN = 3.2 MHz, fOUT = 96 MHz; LDO regulator, direct referencetyp 2 · max 3.1 %1867
Period jitter (Peak-Peak value) Jp125°C; fIN = 3.2 MHz, fOUT = 200 MHz; LDO regulator, direct referencetyp 4.3 · max 7.2 %1867
Current Consumption IDDCk = 96 MHz, VDD = 3.3V; Max. 125°C, Typ. 25°Ctyp 0.9 · max 2.5 mA1867
Current Consumption IDDCk = 200 MHz, VDD = 3.3V; Max. 125°C, Typ. 25°Ctyp 2 · max 3.4 mA1867
MISO setup to SCK tMIS125°C; Master, VDD>2.70Vmin 19.5 ns1867
MISO setup to SCK tMIS125°C; Master, VDD>1.71Vmin 20 ns1867
MISO output valid SCK tSOV125°C; Slave, VDD>2.70Vmin 16.5 ns1867
MISO output valid SCK tSOV125°C; Slave, VDD>1.71Vmin 25 ns1867

Open-source boards using it

14See all 14
  • 4 layers99 × 99 mmMegaBlaster2, the printed circuit board in 3D

    MegaBlaster2

    AidanHockey5/MegaBlaster2

    The latest iteration of my hardware Sega Genesis/Megadrive Video Game Music Player

    120 parts59AGPL-3.0
  • 4 layers50.8 × 81.3 mmAllfc, the printed circuit board in 3D

    Allfc

    peregrine-developments/STACY

    153 parts6MIT
  • 4 layers90.2 × 95.9 mmMainboard v05, the printed circuit board in 3D

    Mainboard v05

    alxklso/ISP-cubesat

    This is the repo for the Isomer Space Program (ISP) 1U CoyoteSat CubeSat mission.

    255 parts1MIT
  • 4 layers40 × 80 mmTitan R3, the printed circuit board in 3D

    Titan R3

    1337bowen/Strife

    96 partsMIT
  • 4 layers39 × 99 mmRoamer, the printed circuit board in 3D

    Roamer

    ezzatisawesome/roamer

    105 parts
  • 4 layers80 × 89 mmFinal Project 4Layer, the printed circuit board in 3D

    Final Project 4Layer

    LeanderU/KnockBox

    Focus: PCB Design of a interactive device using SAMD51 chip

    86 parts
  • 4 layers63.5 × 165.4 mmPCB 2, the printed circuit board in 3D

    PCB 2

    nathaniel-krueger/Capstone_PCB_2

    115 parts
  • 2 layers45 × 40 mmCircuitPythonBadge v1 3, the printed circuit board in 3D

    CircuitPythonBadge v1 3

    neubauek/CircuitPythonBadge

    Open Source Hardware Circuit Python Badge

    91 parts4

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the ATSAMD51J19A-AU?

Yes. The symbol is MCU_Microchip_SAMD:ATSAMD51J19A-A and the footprint Package_QFP:TQFP-64_10x10mm_P0.5mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the ATSAMD51J19A-AU?

TQFP-64, with 64 pins. Its footprint is drawn on this page.

Where is the ATSAMD51J19A-AU datasheet?

Microchip Technology publishes it: the Datasheet link on this page opens it.

Where can I order the ATSAMD51J19A-AU?

JLCPCB lists it as part C619369, with 144 in stock; the sellers' links on this page open their listings.

What can replace the ATSAMD51J19A-AU?

Parts like it in the library: the ATSAMD51J20A-AU by Microchip Technology, the ATSAME51J18A-AU by Microchip Technology, the PIC24EP256GP206-I/PT by Microchip Technology and the PIC32AK1216GC41064-I/PT by Microchip Technology. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the ATSAMD51J19A-AU?

14 boards in 10 repositories on GitHub; the most starred are listed on this page, with their KiCad files.