

Buckboost
Pcb projects
- Size
- 67.3 × 99.1 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 34
- Nets
- 39
- Pads
- 118
- Tracks, vias
- 219, 4
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 6 Dec 2021
- Updated
- 6 Dec 2021
Overview
Buckboost is an open-source printed circuit board by pedrodsk, from the pedrodsk/pcb_cad repository on GitHub. It is a 2-layer board of 67.3 × 99.1 mm with 34 parts on 39 nets, routed with 219 tracks and 4 vias.
It is built around the ATMEGA328-PU, IR2104PBF and LM358, with the IRF540N among its other parts. Its parts include 9 resistors, 8 capacitors, 5 ICs, 5 diodes and 3 connectors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
4ATMEGA328-PU
PDIP-28-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH PDIP-28 Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)IR2104PBF
PDIP-8-40℃~+125℃ 100ns 10V~20V 130mA 150ns 150uA 2 270mA 50ns 680ns Enable shutdown、Interleaved conduction protection、Dead-time control Half-Bridge IGBT、MOSFET PDIP-8 Gate Drivers ROHSInfineon TechnologiesGate DriversLM358
SOP-8-18V~18V 0℃~+70℃ 1.2MHz 10nA 2 24mA 3V~36V 500uA 50nA 5mV 80dB Built-in compensation SOP-8 Operational Amplifier ROHSMSKSEMIOperational AmplifierIRF540N
TO-2201 N-channel 1.35nF 100V 130W 280pF 33A 35mΩ@10V 4V 52nC@10V 85pF N-Channel TO-220 MOSFETs ROHSOSENMOSFETs
README
README.mdpcb_cad
Parts
34| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 1k | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R1, R4, R9 |
| 2 | 10k | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R2, R5 |
| 2 | 22pF | Capacitor_THT:C_Disc_D3.0mm_W1.6mm_P2.50mm | C3, C4 |
| 2 | D | Diode_THT:D_A-405_P7.62mm_Horizontal | D4, D5 |
| 2 | LED | LED_THT:LED_D3.0mm | D1, D2 |
| 2 | R | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R6, R7 |
| 1 | 0.1uF | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C5 |
| 1 | 0.1uF | Capacitor_THT:C_Disc_D3.0mm_W1.6mm_P2.50mm | C1 |
| 1 | 0.33uF | Capacitor_THT:C_Disc_D3.0mm_W1.6mm_P2.50mm | C2 |
| 1 | 10 | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R8 |
| 1 | 100 | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R3 |
| 1 | 1000uF | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C6 |
| 1 | 16mhz | Crystal:Crystal_HC18-U_Vertical | Y1 |
| 1 | 22uF | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C7 |
| 1 | 470uF | Capacitor_THT:CP_Radial_D12.5mm_P5.00mm | C8 |
| 1 | 4N25 | Package_DIP:DIP-6_W7.62mm | U3 |
| 1 | ATmega328-PU | Package_DIP:DIP-28_W7.62mm | U2 |
| 1 | D | Diode_THT:D_P600_R-6_P20.00mm_Horizontal | D3 |
| 1 | Entrada +12V | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | J1 |
| 1 | ICSP | Connector_IDC:IDC-Header_2x03_P2.54mm_Vertical | J2 |
| 1 | IR2104 | Package_DIP:DIP-8_W7.62mm_LongPads | U5 |
| 1 | IRF540N | Package_TO_SOT_THT:TO-220-3_Vertical | Q1 |
| 1 | L | Inductor_THT:L_Toroid_Horizontal_D12.7mm_P20.00mm_Diameter14-5mm_Amidon-T50 | L1 |
| 1 | LM358 | Package_DIP:DIP-8_W7.62mm_LongPads | U4 |
| 1 | LM7805_TO220 | Package_TO_SOT_THT:TO-220-3_Vertical | U1 |
| 1 | SW_Push | Button_Switch_THT:SW_PUSH_6mm_H4.3mm | SW1 |
| 1 | output | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | J3 |
More from pedrodsk/pcb_cad
7- 2 layers99.1 × 63.5 mm

- 2 layers126.4 × 41.3 mm

- 2 layers

- 2 layers117.3 × 116.8 mm

- 2 layers99.7 × 34.3 mm

- 2 layers99.7 × 33 mm

- 2 layers88.9 × 96.5 mm

Similar boards
- 4 layers96.4 × 80.6 mm

Pcb mini racecar
umut181/pcb-mini-racecar
A custom PCB design for a 2WD, IR-controlled differential-drive robot vehicle. Built to run on 2S–6S LiPo battery input, drive 5 V-based microcontrollers, and power low-reduction TT motors: all on a single compact board.
58 parts - 2 layers110.5 × 119.5 mm

SuperCapacitorBike
Fischer-Andrew/The-SuperCap-Bike-Project
I wanted an electric bike with a more dynamic feel than the typical e-bike; one in which you wouldn’t be able to get away with constantly cruising at 30km/h with minimal effort.
123 partsCC0-1.0 - 4 layers110 × 80 mm

- 2 layers130 × 93 mm

Gruppe1-Index3
DileepChilla/Electric-Drive-Systems
motor-control | power-electronics | kicad | atmega328p | ir2104 | irfz44n | pwm | embedded-systems | simulink | gate-driver
55 parts - 2 layers100.1 × 54.7 mm

BinLora
manasdas17/LoRa-SmartGarbageCollection
Deploying smart garbage bins for real time waste management system is one of the key applications of a smart city system.
38 parts1 - 2 layers142 × 92 mm

SPWM
Sudo-Guts/SPWM
Proyecto de control y etapa de potencia de un inversor trifásico con modulación sinusoidal por ancho de pulso (SPWM).
59 parts - 2 layers48.7 × 79.5 mm

DAQsystemUSBrev2
ARTS-Laboratory/Biphasic-data-acquisition-system
Data acquisition system for the biphasic measurement of multifunctional material
28 partsCC-BY-SA-4.0 - 2 layers

Questions
How big is the Buckboost PCB?
It measures 67.3 × 99.1 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Buckboost use?
34 parts, built around the ATMEGA328-PU, IR2104PBF, LM358 and IRF540N. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Buckboost KiCad files?
From the pedrodsk/pcb_cad repository on GitHub, at the commit this page was made from: the board is buckboost/buckboost.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Buckboost design in my own project?
Its repository states no licence, so its author keeps all rights: ask pedrodsk before reusing the design.