
PowerRDP
pbbp0904/HELEN
The rendering above is a rough idea of what this payload will look like with some of its components installed.

The rendering above is a rough idea of what this payload will look like with some of its components installed.
EFM is an open-source printed circuit board by pbbp0904, from the pbbp0904/HELEN repository on GitHub, published under the MIT licence. It is a 2-layer board of 49.2 × 57 mm with 36 parts on 59 nets, routed with 207 tracks and 20 vias.
It is built around the ATXMEGA32A4U-AU. Its parts include 10 capacitors, 6 resistors, 5 ICs, 4 connectors and 1 diode. It belongs with the AVR (ATmega, ATtiny) boards of this library.
This is a PCB designed in KiCad for the UAH SHC HELEN project's Radiation Detection Payload (RDP). This board is intended to gather environmental inupt including temperature, pressure and GPS. This information is processed and saved and potentially shared with an external FPGA.

The rendering above is a rough idea of what this payload will look like with some of its components installed.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 1u | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C1, C2, C3, C6 |
| 3 | 10u | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C5, C7, C9 |
| 2 | 0.1u | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C8, C10 |
| 2 | LM741 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U2, U3 |
| 2 | LOGO | EFM_Libs:HELENlogo | G***, G*** |
| 1 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R6 |
| 1 | 1M | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R2 |
| 1 | 1k | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R3 |
| 1 | 220 | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R1 |
| 1 | 28k | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R4 |
| 1 | 4.7u | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C4 |
| 1 | 6k | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R5 |
| 1 | ATxmega32A4U-AU | Package_QFP:TQFP-44_10x10mm_P0.8mm | U5 |
| 1 | AVR-PDI-6 | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J4 |
| 1 | FB | Inductor_SMD:L_0805_2012Metric_Pad1.15x1.40mm_HandSolder | FB1 |
| 1 | IMU | Connector_Molex:Molex_KK-254_AE-6410-04A_1x04_P2.54mm_Vertical | J2 |
| 1 | LED | LED_SMD:LED_0805_2012Metric | D1 |
| 1 | LOGO | EFM_Libs:Glow | G*** |
| 1 | LOGO | EFM_Libs:mutilator | G*** |
| 1 | L_Small | Inductor_SMD:L_0805_2012Metric_Pad1.15x1.40mm_HandSolder | L1 |
| 1 | Openlog | Connector_Molex:Molex_KK-254_AE-6410-06A_1x06_P2.54mm_Vertical | J1 |
| 1 | SHC_123_BATTERY_HOLDERCR-123-A | SHC_123_BATTERY_HOLDER:SHC_CR-123-A_HOLDER | M1 |
| 1 | Spheres | Connector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_Vertical | J3 |
| 1 | TPS60400DBVR | EFM_Libs:TPS60400DBVR | U1 |
| 1 | XCL206B | EFM_Libs:6-TDFN | U4 |
The 33 most common of 36 parts.

pbbp0904/HELEN
The rendering above is a rough idea of what this payload will look like with some of its components installed.

pbbp0904/HELEN
The rendering above is a rough idea of what this payload will look like with some of its components installed.

espotek-org/Labrador
EspoTek Labrador is a USB device that transforms your PC or smartphone into a fully-featured electronics lab. This repo holds all of the source code!

arlethmichellopez/Curso-de-KiCad
En esta sección integraré el diseño de las PCB's que cree durante el transcurso de mi curso en KiCad

MbFredys/PCB-designs-for-PLATZI-course
PCB design exercises completed during a structured training course, documenting schematic capture, layout, and manufacturing outputs.

open-ephys/ECP5U85-BSE-USB-IO-Tester
IO Test board for ECP5U85-BSE-USB

harp-tech/device.faststepper
A fast moving stepper motor controller device, with acceleration, jerk control, and end stop support

rzoli/robot-control
Building a robot that can map its environment. Software, firmware, pcb design

open-ephys/ECP5U85-BSE-USB
USB development board featuring USB3.0, Lattice ECP5U85 FPGA, and Samtec BSE GPIO Headers

It measures 49.2 × 57 mm and has 2 copper layers, 1.6 mm thick.
36 parts, built around the ATXMEGA32A4U-AU. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the pbbp0904/HELEN repository on GitHub, at the commit this page was made from: the board is electrical/EFM/EFM.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).