4 layers89.3 × 90.7 mm
Breadboard DMM
Acliad/toast-o-meter
Breadboard mounted DMM with volts, amps, ohms, continuity, and diode feature.
152 parts1
2 layers52.1 × 37.4 mm
Consolizer
orangeglo/PS2PSP38Board to connect a PS2 controller to a PSP 2000 (PSP Consolizer)
- Size
- 52.1 × 37.4 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 25
- Nets
- 51
- Pads
- 143
- Tracks, vias
- 333, 41
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 17 Jan 2020
- Updated
- 20 Dec 2021
Overview
Consolizer is an open-source printed circuit board by orangeglo, from the orangeglo/PS2PSP repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 52.1 × 37.4 mm with 25 parts on 51 nets, routed with 333 tracks and 41 vias.
It is built around the ATMEGA328PB-AU, MIC5504-3.3YM5 and L102021ML04Q. Its parts include 9 connectors, 5 capacitors, 3 ICs, 1 resistor and 1 diode. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
3
ATMEGA328PB-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 27 2KB 32KB 8 Bit AVR Built-in FLASH Power-on reset (POR)、Undervoltage detection (BOR/LVD/LVR/LVI)、Watchdog reset、External pin reset (NRST)、Built-in general-purpose timer、Programmable watchdog、Touch function TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
MIC5504-3.3YM5
SOT-23-5-40℃~+125℃@(Tj) 1 120uVrms 15uA 180mV@(300mA) 3.3V 300mA 5.5V 75dB@(1kHz) Fixed Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTECH PUBLICVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsL102021ML04Q
插件-30℃~+65℃ 28V PC Pin Rectangular Columnar SPDT Through Hole Plugin Slide Switches ROHSC&KSlide Switches
README
README.mdPS2PSP
These are PCB design and arduino software files for a circuit board that converts a PS2 controller into signals a PSP2000 motherboard can understand. The circuit board is designed to have the PSP power cable routed through it, so you can boot up the PSP and the adapter with a basic toggle switch.
Parts
25| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | H1, H2, H3, H4 |
| 3 | 0.1 uF | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C3, C4, C5 |
| 2 | 1 uF | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C1, C2 |
| 1 | 68 | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R1 |
| 1 | ATmega328PB-AU | Package_QFP:TQFP-32_7x7mm_P0.8mm | U2 |
| 1 | AVR-ISP-6 | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J4 |
| 1 | Analog | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J8 |
| 1 | Conn_01x06 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Horizontal | J5 |
| 1 | L102021ML04Q | L102011ML04Q | S1 |
| 1 | LED | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1 |
| 1 | MCP4651-103E_ST | MCP4651-103E_ST:SOP65P640X120-14N | U3 |
| 1 | MIC5504-3.3YM5 | Package_TO_SOT_SMD:SOT-23-5 | U1 |
| 1 | PS2 Controller | Connector:ps2_connector | J6 |
| 1 | Power IN | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | Power OUT (to PSP) | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Horizontal | J9 |
| 1 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP2 |
| 1 | center ribbon | 1-1734592-0:TE_1-1734592-0 | J7 |
| 1 | left ribbon | 1-1734592-0:TE_1-1734592-0 | J3 |
| 1 | right ribbon | 1-1734592-4:TE_1-1734592-4 | J1 |
Similar boards
- 6 layers228.6 × 228.6 mm
- 2 layers88.4 × 62 mm
EStopTX
ParadigmEngineering/igvc-2023-hardware
Intelligent Ground Vehicle Competition (Spring 2023) hardware for the Paradigm Engineering Student Group
13 parts1 - 2 layers47.2 × 115.3 mm
- 2 layers78 × 130 mm
Lofence
kiu/lofence
LoFence is a LoRaWAN capable IoT electric fence monitoring system running on the The Things Network.
65 parts142MIT - 2 layers30 × 40 mm
- 2 layers189.6 × 31.8 mm
Arm interface board panel
Roboy/Arm_interface_board
Board containing all the control units and power distribution for the servos in the arms.
129 parts1 - 2 layers102 × 81.5 mm
C64pico
silvervest/c64pico
This is a tiny emulated C64 running on a Raspberry Pi Pico! Full details of the build can be found at https://www.youtube.com/watch?v=hgLhGpbC6E4
97 parts86
Questions
How big is the Consolizer PCB?
It measures 52.1 × 37.4 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Consolizer use?
25 parts, built around the ATMEGA328PB-AU, MIC5504-3.3YM5 and L102021ML04Q. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Consolizer KiCad files?
From the orangeglo/PS2PSP repository on GitHub, at the commit this page was made from: the board is hardware/PSP_Consolizer/consolizer.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Consolizer design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).