
HAN ESP TSS721
UtilitechAS/amsreader-firmware
ESP8266 and ESP32 compatible firmware to read, interpret and publish data to MQTT from smart electrical meters, both DLMS and DSMR is supported

ESP8266 Development Board
Orc esp1 is an open-source printed circuit board by OpenRoboticsCompany, from the OpenRoboticsCompany/orc-esp1 repository on GitHub. It is a 2-layer board of 66 × 66 mm with 81 parts on 67 nets, routed with 358 tracks and 48 vias.
It is built around the LM1117-3.3. Its parts include 22 resistors, 16 diodes, 3 capacitors, 3 connectors and 2 ICs. It belongs with the ESP8266 boards of this library.

Front:

Back:

This board provides power, GPIO, and Micro SD to the commonly-available ESP8266 wifi modules. This first revision is intended for internal use at Open Robotics Company, but may find it's way out to the world also.
Built using KiCad EDA
PCB images courtesy of OSHPark's magical preview.
Please note that we used a nightly dev build of KiCad for this project. You cannot open the files in the current stable version (4.0.5 as of this writing). We used kicad-r7402.f631ae2-x86_64 on Windows. It's possible that later versions will open the files, but because nightly builds are always changing, you never know!
Designed by Aaron Kondziela. Copyright 2017 Open Robotics Company LLC
If any files (datasheets, etc) have been included here that are not our original work, they are (obviously) the copyright of their respective authors.
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | 200R | Resistors_SMD:R_0603_HandSoldering | R4, R5, R6, R7, R8, R9, R10, R11, R12, R13, R14, R15, R16, R17, R18, R19 |
| 3 | 10K | Resistors_SMD:R_0603_HandSoldering | R1, R2, R3 |
| 3 | 470R | Resistors_SMD:R_0603_HandSoldering | R20, R21, R22 |
| 3 | Power Schottky | Diodes_SMD:SMB_Handsoldering | D11, D12, D13 |
| 2 | 0.1uF | Capacitors_SMD:C_0603_HandSoldering | C2, C3 |
| 1 | 22uF | Capacitors_Tantalum_SMD:Tantalum_Case-B_EIA-3528-21_Hand | C1 |
| 1 | BARREL_JACK | orc-esp1:BARREL_JACK_AK | JACK_POWER1 |
| 1 | BATT_PWR_LED | LEDs:LED_0603 | D14 |
| 1 | BOOT_JP | orc-esp1:Jumper_1206_NC_DNP | JP2 |
| 1 | BOOT_JP2 | orc-esp1:Jumper_1206_NC_DNP | JP9 |
| 1 | BOOT_JP3 | orc-esp1:Jumper_1206_NC_DNP | JP1 |
| 1 | Boot | Buttons_Switches_THT:SW_PUSH_6mm | SW2 |
| 1 | CONN_01X06 | Pin_Headers:Pin_Header_Straight_1x06 | P3 |
| 1 | CONN_01X10 | Pin_Headers:Pin_Header_Straight_1x10 | P4 |
| 1 | EN_JP | orc-esp1:Jumper_1206_NC_DNP | JP10 |
| 1 | ESP-12q | orc-esp1:ESP-12-Q | U2 |
| 1 | FTDI Serial | Pin_Headers:Pin_Header_Straight_1x06_Pitch2.54mm | P1 |
| 1 | GND | Wire_Pads:SolderWirePad_single_1-2mmDrill | GND |
| 1 | GPIO12_JP | Pin_Headers:Pin_Header_Straight_1x02 | JP13 |
| 1 | GPIO12_LED | LEDs:LED_0603 | D6 |
| 1 | GPIO13_JP | Pin_Headers:Pin_Header_Straight_1x02 | JP14 |
| 1 | GPIO13_LED | LEDs:LED_0603 | D7 |
| 1 | GPIO14_JP | Pin_Headers:Pin_Header_Straight_1x02 | JP15 |
| 1 | GPIO14_LED | LEDs:LED_0603 | D8 |
| 1 | GPIO15_JP | Pin_Headers:Pin_Header_Straight_1x02 | JP16 |
| 1 | GPIO15_LED | LEDs:LED_0603 | D9 |
| 1 | GPIO16_JP | Pin_Headers:Pin_Header_Straight_1x02 | JP17 |
| 1 | GPIO16_LED | LEDs:LED_0603 | D10 |
| 1 | GPIO4_JP | Pin_Headers:Pin_Header_Straight_1x02 | JP11 |
| 1 | GPIO4_LED | LEDs:LED_0603 | D4 |
| 1 | GPIO5_JP | Pin_Headers:Pin_Header_Straight_1x02 | JP12 |
| 1 | GPIO5_LED | LEDs:LED_0603 | D5 |
| 1 | JACK_PWR_LED | LEDs:LED_0603 | D15 |
| 1 | LM1117-3.3 | TO_SOT_Packages_SMD:SOT-223 | U1 |
| 1 | LOGO | orc-esp1:LOGO-orc-20mm-flip | G*** |
| 1 | MICRO_USB | orc-esp1:USB_Micro-B_AK | USB_POWER1 |
| 1 | Micro_SD_Bomb | orc-esp1:Sumai-Micro-SD-Bomb | TF1 |
| 1 | POWER_1x2 | Pin_Headers:Pin_Header_Straight_1x02_Pitch2.54mm | BATTERY1 |
| 1 | REG_PWR_LED | LEDs:LED_0603 | D1 |
| 1 | Reset | Buttons_Switches_THT:SW_PUSH_6mm | SW1 |
| 1 | RxD_LED | LEDs:LED_0603 | D2 |
| 1 | SD_JP3 | orc-esp1:Jumper_1206_NC_DNP | JP3 |
| 1 | SD_JP4 | orc-esp1:Jumper_1206_NC_DNP | JP4 |
| 1 | SD_JP5 | orc-esp1:Jumper_1206_NC_DNP | JP5 |
| 1 | SD_JP6 | orc-esp1:Jumper_1206_NC_DNP | JP6 |
| 1 | SD_JP7 | orc-esp1:Jumper_1206_NC_DNP | JP7 |
| 1 | SD_JP8 | orc-esp1:Jumper_1206_NC_DNP | JP8 |
| 1 | TxD_LED | LEDs:LED_0603 | D3 |
| 1 | USB_PWR_LED | LEDs:LED_0603 | D16 |
The 71 most common of 81 parts.

UtilitechAS/amsreader-firmware
ESP8266 and ESP32 compatible firmware to read, interpret and publish data to MQTT from smart electrical meters, both DLMS and DSMR is supported

karawin/Ka-Radio
A wifi webradio with only low cost boards ESP8266 and VS1053 by Jp Cocatrix


doudar/SmartSpin2k
Transform your spin bike into a Smart Trainer!

plinkysynth/plinky_public
a public release of the plinky sw and hw

eddyem/stm32samples
Code samples and ready projects based on bare-metal STM32


It measures 66 × 66 mm and has 2 copper layers, 1.6 mm thick.
81 parts, built around the LM1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the OpenRoboticsCompany/orc-esp1 repository on GitHub, at the commit this page was made from: the board is orc-esp1.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask OpenRoboticsCompany before reusing the design.