2 layers133.2 × 75.4 mm
2 layers50 × 22.9 mm
RX Module nRF24L01
obbo-pl/RC-RX-NRF24L013RC receiver with NRF24L01 module and compatible with the CABELL protocol
- Size
- 50 × 22.9 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 33
- Nets
- 33
- Pads
- 119
- Tracks, vias
- 305, 15
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 7 Sep 2020
- Updated
- 2 Mar 2023
Overview
RX Module nRF24L01 is an open-source printed circuit board by obbo-pl, from the obbo-pl/RC-RX-NRF24L01 repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 50 × 22.9 mm with 33 parts on 33 nets, routed with 305 tracks and 15 vias.
It is built around the ATMEGA328-AU, TPS73601DBV and TPS73633DBV. Its parts include 11 connectors, 9 capacitors, 8 resistors, 4 ICs and 1 crystal. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
3
ATMEGA328-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
TPS73601DBV
SOT-23-5-40℃~+125℃@(Tj) 1 1.2V~5.5V 200mV@(400mA) 5.5V 500mA 58dB@(100Hz) Adjustable Over Current Protection、Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTPS73633DBV
SOT-23-5-40℃~+125℃@(Tj) 1 3.3V 30uVrms 400mA 5.5V 550uA 58dB@(10kHz) 75mV@(400mA) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Enable control、Reverse-polarity current protection、Noise bypass terminal Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdRC-RX-NRF24L01
RC receiver with NRF24L01 module and compatible with the CABELL protocol
Main features:
- dimensions: 50.0 * 22.9 * 12.2mm (without case),
- weight: approx. 9g (without case),
- 2.4GHz NRF24L01 G-24 module,
- communication protocol compatible with CABELL v3,
- 8 channels,
- supply voltage 4.0V - 6.2V,
- serial port and I2C for telemetry,
- parameter configuration via serial port (9600bps),
- output signal levels: 5V,
For more information: www.obbo.pl
Parts
33| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | Conn_01x03 | obbo_footprints:PinHeader_3x01_P2.54mm_Horizontal | J1, J2, J3, J4, J5, J6, J7, J8, J10, J11 |
| 5 | 100n | obbo_footprints:C_0805K | C3, C4, C6, C7, C8 |
| 3 | 10k | obbo_footprints:R_0805K | R3, R5, R6 |
| 2 | 10u | Capacitor_SMD:C_1210_3225Metric_Pad1.42x2.65mm_HandSolder | C1, C5 |
| 2 | 18p | obbo_footprints:C_0805K | C9, C10 |
| 2 | 3k3 | obbo_footprints:R_0805K | R7, R8 |
| 1 | 16MHz | obbo_footprints:Crystal_SMD_5032-4Pin_5.0x3.2mm_HandSoldering | Y1 |
| 1 | 22k | obbo_footprints:R_0805K | R2 |
| 1 | 47k* | obbo_footprints:R_0805K | R4 |
| 1 | 68k* | obbo_footprints:R_0805K | R1 |
| 1 | ATmega328-AU | Package_QFP:TQFP-32_7x7mm_P0.8mm | U3 |
| 1 | Conn_01x01 | obbo_footprints:Pin_D1.0mm_L10.0mm_LooseFit | J9 |
| 1 | NRF24L01_Breakout | obbo_footprints:nRF24L01-GT24_Breakout_PinHeader_2x04 | U4 |
| 1 | TPS73601DBV | Package_TO_SOT_SMD:SOT-23-5 | U1 |
| 1 | TPS73633DBV | Package_TO_SOT_SMD:SOT-23-5 | U2 |
Similar boards
- 2 layers342.9 × 109.6 mm
- 2 layers30 × 30.2 mm
Paw3395 breakout board
vnguyen31/PixArt-PAW3395-Breakout-Board
Fully functioning Breakout Board with SPI pin headers for PAW3395 Motion Sensor
28 parts11MIT - 2 layers22 × 25 mm
- 2 layers336.8 × 109.9 mm
- 2 layers110 × 94 mm
- 2 layers22.8 × 24 mm
- 2 layers100 × 74 mm
Questions
How big is the RX Module nRF24L01 PCB?
It measures 50 × 22.9 mm and has 2 copper layers, 1.6 mm thick.
What parts does the RX Module nRF24L01 use?
33 parts, built around the ATMEGA328-AU, TPS73601DBV and TPS73633DBV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the RX Module nRF24L01 KiCad files?
From the obbo-pl/RC-RX-NRF24L01 repository on GitHub, at the commit this page was made from: the board is hardware/RX-Module-nRF24L01.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the RX Module nRF24L01 design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).